Comparison Vincent SA-T7 vs Vincent SA-T8

— transistor. The term "semiconductor" is also used, since it is on such materials that the operation of transistors is based. Such an element base is the most popular in modern amplifiers: transistors are able to provide high sound quality with a minimum of distortion, while they are inexpensive, unpretentious in use, do not require powerful cooling systems, and are also resistant to shock and shaking. However they can somewhat lose to lamps in terms of the “atmospheric” sound (for more details, see below); however, this is already a matter of personal tastes of each user.

— Lamp. Element base built on radio tubes. Historically, this variant predates the transistor variant, but pure tube amps are now relatively rare. This is due not only to the high cost of such devices, but also to their large dimensions and some inconvenience in use: after switching on, it takes some time to “warm up”, and the lamps themselves have a relatively short service life. In addition, tube amplifiers are significantly inferior to transistor amplifiers in terms of signal purity (in particular, harmonic coefficient, see below); however, this point cannot be called a clear disadvantage. The fact is that distortion from tube circuits is much more pleasant to the ear than from transistor ones; moreover, they are one of the components of the notorious "warm tube sound". Therefore, most modern tube amplifiers belong to the Hi-E...nd category and are designed for lovers of such a sound.

— Hybrid. Amplifiers that combine both of the above types of circuits in their design. Thanks to this, it becomes possible to achieve a characteristic "tube" sound at a relatively low cost and acceptable dimensions of the device. Most of these models are of the integrated type (see above) and combine a tube preamp with transistor output stages.

The model of tubes installed in a tube or hybrid type amplifier (see "Element base"). The capabilities of the device largely depend on the lamps used in the design, including small details of the sound, not directly spelled out in the characteristics. In addition, this information allows, to some extent, to assess the overall level of the model. On the other hand, in fact, it can only be useful to extremely demanding listeners, attentive to every detail; most users, including audiophiles, will only need information about the type of tubes when they need to be replaced.

The range of audio frequencies that the amplifier is capable of handling. The wider this range, the more complete the overall picture of the sound, the less likely it is that too high or low frequencies will be “cut off” by the output amplifier. However, note that the range of sound audible to a person is on average from 16 Hz to 20 kHz; There are some deviations from this norm, but they are small. At the same time, modern Hi-Fi and Hi-End technology can have a much wider range — most often it is a kind of "side effect" of high-end circuits. Some manufacturers may use this property for promotional purposes, but it does not carry practical value in itself.

Note that even within the audible range it does not always make sense to chase the maximum coverage. It is worth, for example, to take into account that the actually audible sound cannot be better than the speakers are capable of giving out; therefore, for a speaker system with a lower threshold of, say, 70 Hz, there is no need to look for an amplifier with this figure of 16 Hz. Also, do not forget that a wide frequency range in itself does not absolutely guarantee high sound quality — it is associated with a huge number of other factors.

This indicator describes the amount of non-linear distortion introduced by the amplifier into the processed signal. Such distortions are not necessarily perceived as extraneous noise, but they degrade the quality of the sound anyway — for example, they can make it more deaf. It is almost impossible to avoid them, but it can be reduced to levels inaudible to the human ear.

As a result, the harmonic distortion factor (harmonics) is one of the main parameters describing the overall sound quality in Hi-Fi and Hi-End amplifiers. The lower it is, the clearer the sound. Hundredths of a percent are considered a good indicator for modern amplifiers, thousandths and below are excellent. The exceptions are tube and hybrid models, for which rather high harmonic coefficients are allowed; see "Element base" for more details.

The sensitivity and dynamic impedance of the amplifier when a signal is applied to the RCA line input.

Under the sensitivity of any input (except optical) is meant the lowest signal voltage at this input, at which the amplifier is able to provide normal nominal power values (see "Power per channel (8Ω)"). This parameter determines, first of all, the requirements for the signal source. On the one hand, the voltage provided by this source must not be lower than the input sensitivity of the amplifier, otherwise the latter simply will not give the claimed characteristics. However, a significant excess in voltage should not be allowed, otherwise the sound will begin to be distorted. More detailed recommendations on choosing an amplifier by sensitivity are described in special sources.

For any input other than optical, it is believed that the higher this indicator, the less distortion the amplifier introduces into the signal. The minimum level of input impedance in modern models is considered to be 10 kOhm, and in high-end devices it can reach several hundred kOhm.

— Euroblock. Analogue audio input (usually line level) using a Euroblock connector. This connector, used mainly in professional audio equipment, is remarkable in that it is attached to the wire using terminals. This is extremely convenient when working with stripped wires (which is often required in professional applications): screwing such a wire to the plug once and connecting / disconnecting the plug to the Euroblock connector is much easier than constantly unscrewing / screwing the terminals. In addition, such a connection is often made balanced (see "XLR (balanced)" below). Inputs of this type are found mainly in information and information-concert amplifiers (see above).

— Phono. Dedicated input for connecting to the amplifier turntables; often has a suffix indicating the type of cartridge that is compatible, such as "Phono MM" or "Phono MM/MC" (see "Advanced — Phono Stage" for details). Despite the proliferation of digital formats, these players are still highly regarded by audiophiles for their high quality and fidelity, and are often used in premium audio systems. However, connecting a "turntable" has its own characteristics — in particular, it requires a phono stage (for more details, see ibid.) — and standard inputs are unsuitable for this purpose. Therefore, a Phono jack is a must if you want to connect your turntable directly, without an external phono stage.

— USB B. The USB interface is widely used in com...puter technology for various peripherals. The presence of a type B input means that the amplifier can be connected to a computer as an external controlled device (slave). Most often, with this connection, it is used as an external sound card or audio interface — this provides higher sound quality and more extensive options for its settings than most built-in sound cards, even expensive ones. However, the matter is not limited to this: in some models, via USB type B, you can update the firmware or change the special parameters of the amplifier.

— Coaxial S / P-DIF. Digital audio input, a variation of the S/P-DIF interface based on a conventional electrical signal (the second variation, optical, is described below). Usually uses a common RCA connector, known as a "tulip", but has rather strict cable requirements. The bandwidth of any version of S / P-DIF is quite sufficient even for high-quality multi-channel sound, and the coaxial version itself is simpler, cheaper and more reliable than the optical one, but more susceptible to interference.

— Optical. Input for transmitting digital sound using light signals, via TOSLINK fiber optic cable; one of the versions of the S/P-DIF standard. The main advantage of optical fiber over traditional electrical cables is complete insensitivity to electrical interference; at the same time, it is more expensive and requires rather careful handling (in particular, it does not tolerate sharp bends).

— Balanced digital ( AES/EBU). The AES/EBU interface is used in the professional field to transmit audio in digital format. It can use several connection types; in this case, it means transmission over the so-called balanced line using an XLR connector. Both the principle of balanced connection and the connector itself are described in detail in the “XLR (balanced)” section below — however, in the case of AES / EBU, we are talking about a digital signal, not an analogue signal.

— COM port ( RS-232). A connector used to control the amplifier from a computer. Through it, you can change the settings, incl. and quite thin, and in some models even update the firmware. Usually, for such purposes, special software is required, which can be supplied with the amplifier.

— Control input (IR). Connector for connecting an external infrared remote control receiver. When properly placed, such a receiver will allow you to use the remote control even in places where the signal from the remote control cannot reach the main (built-in) sensor — for example, in another room. For such purposes, not only sensors can be used as a separate device, but also system components that are compatible with the remote control — for example, players or tuners.

The number of line inputs in the amplifier design using the RCA interface. Unlike the Main input (see above), which can work with the same connectors, when connected to a linear RCA, the signal goes through all the stages of processing provided for in the amplifier — for example, adjusting the balance or frequencies (see "Adjustments"), etc. .P.

See “Amplifier Input (Main)” for details on the connector itself. Here we note that when using RCA as a linear interface, a pair of such connectors is considered one input. This is due to the fact that only one channel can be transmitted over one coaxial cable, so a pair is needed to work with stereo sound.

The number of signal inputs (of any type) determines how many signal sources can be simultaneously connected to the amplifier. Accordingly, it is worth choosing a model according to the number of inputs, taking into account the expected number of such sources: after all, it is easier to connect them all and select them through the amplifier’s remote control or control panel than to fiddle with reconnecting every time.

The number of stereo inputs in the design of the amplifier with XLR connectors having three pins and capable of providing the so-called balanced connection. Note that we are talking about an analogue line input, the signal from which passes through all additional processing circuits (for example, bass / treble settings, see "Adjustments"); do not confuse it with Main and balanced digital AES / EBU — these are different interfaces, despite the identity of the connectors.

The main advantage of this connection is that the functions of noise reduction and shielding from interference are performed by the cable itself. This moment is especially useful when it is necessary to connect system components located at a large distance from each other (from 2 m): a balanced cable maintains signal purity even at a rather large length. The quality of such a connection is at least indicated by the fact that balanced XLR is a standard interface for professional recording studios. And its presence in the amplifier, usually, indicates a high level of the device.

There are usually two XLR inputs in amplifiers — this is the minimum number needed to work with stereo sound, and more is most often not required in fact.

— Bass adjustment. The presence in the amplifier of a separate low-frequency level control, in other words, bass volume. The ratio of low and high frequencies largely determines the overall picture of the sound; the optimal options for this ratio for different cases will be different, and they depend on a number of factors — from the type of audio being played to the personal tastes of the listener. Anyway, the bass control provides an additional opportunity to fine-tune the sound of the entire system. It is often combined with a treble control (see below); in fact, this combination is the simplest version of the equalizer.

— Treble adjustment. The presence in the amplifier of a separate volume control for high frequencies. The meaning of this function is completely similar to the bass control described above, only it works with a different frequency band.

— Balance adjustment. The presence in the amplifier of adjusting the balance between the channels. This setting is used in stereo sound: by changing the position of the knob, you can increase the volume for one channel and decrease it for another. Due to this, the conditional centre of the perceived sound shifts towards the speaker that sounds louder. This feature can be very useful for correcting the sound stage — for example, if the speakers have different sensitivity, badly placed, or the signal itse...lf is not properly balanced. At the same time, the balance controller introduces additional elements into the design, which increases the likelihood of interference. And therefore, in top-class amplifiers, it may not be provided at all.

— Adjustment of input sensitivity. Ability to change the input sensitivity of the amplifier; For details on this parameter, see "Input Sensitivity (Line Input)". Also note here that the adjustment itself can be useful when working with several sound sources: it allows you to easily reconfigure the amplifier for each of these sources in order to provide the desired output power level and at the same time avoid distortion.

— Level adjustment. The presence in the amplifier of its own level control, in other words, a system that allows you to change the volume of the sound (by changing the actual output power). In modern home amplifiers (see above), this adjustment is common to all channels, and it is responsible for the actual volume; sometimes using the control on the amplifier is more convenient than on another component of the audio system. But in concert models, each channel, usually, is equipped with its own regulator, thanks to which there are many opportunities for fine-tuning the sound to a specific situation.

— Loudness. This function allows you to adjust the tone of the sound at a low volume. Its necessity is connected with the fact that the human ear perceives a quiet sound differently than a loud one; because of this, even high-quality sound at low volume will seem “blurry”, not clear enough. Loudness corrects this by boosting certain frequencies. Usually this mode is enabled by the user at will.