Routers & Trimmers

Tungsten Carbide Tipped for abrasive materials such as Chipboard, MDF, Plywood, Hardwoods and Hard Plastics. Two flutes give a clean finish to the cut edges. All cutters are suitable for plunge routers. Cutters above and including 9.5mm have TCT plunge Centre tip

Cutters are chosen for fast free cutting, when cutting speed takes preference over finish. Cutters with prefix S are Solid Carbide. Cutters of 2.0mm diameter and below should have a maximum of 1.0mm depth of cut per pass. Small diameter tools must be handled with care to avoid breakage. Single flute cutters should not be used in eccentric chucks.

These plug cutters are designed to exactly fit the counterbored holes produced by group 62 and 63 Trend cutters. Recommended speed - 1,000-20,000 /min. TCT for use with drilling machines or routers. H.S.S. 1/4in Shank. C = 9.5 mm D = 16 mm Plug Body Diameter. 16 mm

These plug cutters are designed to exactly fit the counterbored holes produced by group 62 and 63 Trend cutters. Recommended speed - 1,000-20,000 /min. H.S.S. 1/4in Shank. C = 16 mm D = 12 mm Plug Body Diameter. 22 mm

Cutters are chosen for fast free cutting, when cutting speed takes preference over finish. Cutters with prefix S are Solid Carbide. Cutters of 2.0mm diameter and below should have a maximum of 1.0mm depth of cut per pass. Small diameter tools must be handled with care to avoid breakage. Single flute cutters should not be used in eccentric chucks.

Trend Single Flute Cutters are chosen for fast, free cutting when cutting speed takes preference over finish. If you require a cleaner cut, two flute cutters are recommended. Suitable for grooving, rebating, morticing and drilling. Cutters of 2.0mm diameter and below should have a maximum of 1.0mm depth of cut per pass. Small diameter tools must be handled with care to avoid breakage. Single flute cutters should not be used in eccentric chucks.

These cutters are used extensively for routing edge moulds, face grooves, columns, fluting, water slots, engraving and panel moulds in products such as desk tops, fire surrounds, draining boards and picture frames. These cutters are suitable for use on all natural timbers and man-made boards. TC. 1/2in Shank R = 12.7 mm D = 25.4 mm C = 15.9 mm

15 Pce cutter set, containing a range of popular cutters. Suitable for grooving, profiling and moulding. Use on softwoods, hardwoods, MDF and plywood. Supplied in a plastic carry case.

Freud F03FR01535 RB Double Flute Straight Bit 12.7 x 38.1mm x 1/2" Shank (12-12250P) The Freud F03FR01535 measures 12.7 x 38.1mm / 1/2in with a 1/2 inch shank. Freud's huge selection of carbide tipped and solid carbide double flute straight bits are ideal for grooving, edge-routing and other general purpose routing tasks. The precise hook and shear angles provide fast cutting and a smooth finish in hardwood, softwood, plywood and composite materials. Tips are relieved to allow for efficient plunge cuts. Designed for use in CNC, hand-held and table-mounted routers. Features: Freud Tico Hi-Density Carbide Clean cuts in solid wood, plywood and composites Use in CNC, hand-held and table-mounted …

Freud F03FR01533 RB Double Flute Straight Bit 12.7 x 31.8mm x 1/2" Shank (12-11850P) The Freud F03FR01533 measures 12.7 x 31.8mm / 1/2in with a 1/2 inch shank. Freud's huge selection of carbide tipped and solid carbide double flute straight bits are ideal for grooving, edge-routing and other general purpose routing tasks. The precise hook and shear angles provide fast cutting and a smooth finish in hardwood, softwood, plywood and composite materials. Tips are relieved to allow for efficient plunge cuts. Designed for use in CNC, hand-held and table-mounted routers. Features: Freud Tico Hi-Density Carbide Clean cuts in solid wood, plywood and composites Use in CNC, hand-held and table-mounted …

Freud F03FR01529 RB Double Flute Straight Bit is ideal for grooving, edge-routing and other general-purpose routing tasks The Freud F03FR01529 measures 9.5 x 31.8mm / 3/8in with a 1/2 inch shank. Freud's huge selection of carbide tipped and solid carbide double flute straight bits are ideal for grooving, edge-routing and other general-purpose routing tasks. The precise hook and shear angles provide fast cutting and a smooth finish in hardwood, softwood, plywood and composite materials. Tips are relieved to allow for efficient plunge cuts. Designed for use in CNC, hand-held and table-mounted routers. Features: Freud Tico Hi-Density Carbide Ideal For: grooving and edge-routing applications Use …

Freud F03FR01526 RB Double Flute Straight Bit 9.5 x 25.4mm x 1/2" Shank (12-10850P) The Freud F03FR01526 measures 9.5 x 25.4mm / 3/8in with a 1/2 inch shank. Freud's huge selection of carbide tipped and solid carbide double flute straight bits are ideal for grooving, edge-routing and other general purpose routing tasks. The precise hook and shear angles provide fast cutting and a smooth finish in hardwood, softwood, plywood and composite materials. Tips are relieved to allow for efficient plunge cuts. Designed for use in CNC, hand-held and table-mounted routers. Features: Freud Tico Hi-Density Carbide Clean cuts in solid wood, plywood and composites Use in CNC, hand-held and table-mounted routers …

With ball bearing guide. To trim plastic or laminate facings. Used extensively in cabinet making and shop fitting. Suitable for straight or curved work.

Use for bevelling and chamfering. A flat, approximately 1.0mm, will be found on V Groove tip.

Two Flute V-Grooving Bits for veining work and decor of panels. 1/4" Shank Diameter 45 V-Grooving

Bevel Edge Trimming Bit with ball bearing or pin guide. To trim laminate producing a bevelled edge. Suitable for straight or shaped work. 1/4" Shank Diameter (Pin Guided)

Trend Trade range two flute router cutters have extra long shanks and are designed to meet the demanding needs of the professional trademen. They have a 2mm micrograin Tungsten Carbide tips for cutting the most abrasive materials to give extra long life. They have a PTFE coat, indicated by distinctive black colouring and produce a clean finish to abrasive timbers such as chipboard, MDF, plywood and certain hardwoods. The dimensions are etched on the extra long 40mm shanks for quick identification and are suitable for mortice and worktops applications.

Trend Trade range two flute router cutters have extra long shanks and are designed to meet the demanding needs of the professional trademen. They have a 2mm micrograin Tungsten Carbide tips for cutting the most abrasive materials to give extra long life. They have a PTFE coat, indicated by distinctive black colouring and produce a clean finish to abrasive timbers such as chipboard, MDF, plywood and certain hardwoods. The dimensions are etched on the extra long 40mm shanks for quick identification and are suitable for mortice and worktops applications.

All slotters are precision made in TCT grade for long life when cutting the most abrasive materials. Requires an arbor Ref. 33/60 and suitable diameter bearing to govern depth of cut. Specifications • Dia Metric: 36 • Sawbore Imperial: 1/4 • Saw Kerf Metric: 2 • Saw Teeth: 2

These staff bead are ideal for producing nosings and attractive edges. Edge cut only. Specifications • Shank Diameter: 1/4 • Dia Metric: 20 • Dia Imperial: 25/32 • Cut Length Metric: 19.1 • Cut Length Imperial: 3/4 • Overall Length Metric: 57 • Overall Length Imperial: 2 1/4 • Radius 1 Metric: 5.2

These cove style cutters with two flutes, give radiused grooves for decorative panel finishes and board edges. For deep channels, take a series of passes. Specifications • Shank Diameter: 1/4 • Dia Metric: 12.7 • Dia Imperial: 1/2 • Cut Length Metric: 7.9 • Cut Length Imperial: 5/16 • Overall Length Metric: 48.5 • Radius 1 Metric: 6.3 • Radius 1 Imperial: 1/4

This quarter radius can produce a sunk bead or a nosing mould. The bearing eases setting up & enables curved edges to be profiled. Specifications • Shank Diameter: 1/4 • Dia Metric: 22 • Cut Length Metric: 16 • Overall Length Metric: 60 • Bearing Dia Metric: 16 • Radius 1 Metric: 10

Pin guided rounding over cutters are ideal for panel work and edge mounting, all can be used on natural timbers, man-made particles and fibre boards. Popular uses include edging window frames, glazing bars, cabinets, table tops, pencil rounds, trophies, shelves and fire surrounds. They can also be used to produce bullnose edge moulds. Small solid guide pins can follow more intricate shapes in contrast to bearing guided cutters.

Ovolo and rounding over cutters are ideal for panel work and edge moulding, all can be used on natural timbers, man-made particles and fibre boards. Popular uses include edging window frames, glazing bars, cabinets, table tops, pencil rounds, trophies, shelves and fire surrounds. They can also be used to produce bullnose edge moulds. Small solid guide pins can follow more intricate shapes in contrast to bearing guided cutters. Specifications Tooling T.C 1/4in Shank. D =3/8 inch. D =9.5 mm. D2=3.2 mm. C =9 mm. R =2.5 mm.