Comparison Hisense 55U7KQ 55 " vs Hisense 55A7KQ 55 "

— Edge LED — side backlight of the matrix. In this case, the LEDs are distributed around the perimeter of the screen. To evenly distribute the backlight, the background of the matrix has a special reflector. An important advantage of TVs with Edge LED backlighting is the minimum thickness of the device. Among the shortcomings, one can note the presence of glare at the edges, which appear under certain conditions. Glare may be visible in scenes where dark hues predominate.

— Direct LED — rear matrix backlight. In this case, the LEDs are evenly distributed over the entire screen area. The Direct LED backlight makes the image contrast and bright at the same time. TVs with this technology have good colour reproduction. Among the shortcomings can be noted increased power consumption and increased dimensions. Additionally, such TVs have a large delay (Input lag), which is why Direct LED backlit screens are poorly suited for dynamic games.

— FALD (Full-Array Local Dimming) is a backlight technology widely used in LG TVs. A close analogue of FALD is the Direct LED backlight. The LEDs are also evenly spaced across the entire surface of the matrix, but FALD technology provides a bright, colour-rich image with high contrast. Another distinctive feature of FALD is the ability to reproduce natural blacks. When black is displayed on the screen, the LEDs are turn...ed off in groups, by sector, which allows to make black extremely saturated. Of course, the abundance of LEDs on the matrix makes the TV more massive, and at the same time heavy. The appetite for electricity in such models is above average.

— Mini LED. Screen backlight system on a substrate of reduced LEDs (hence the Mini prefix). On the same plane of the TV panel, the number of LEDs has increased several times, if we draw parallels with traditional LED systems. As a result, the canvas with Mini LED backlight has many times more local dimming zones of the picture (Local Dimming), which is necessary for the correct operation of the extended dynamic range image technology. For playing HDR content, Mini LED systems are much better than ordinary LCDs.

— Dual LED. Proprietary backlight system used in Samsung TVs. The technology involves illuminating the image on the screen with two types of LEDs: one emits light in a cold spectrum, the other in a warm one. The Dual LED enhances colour reproduction and enhances detail contrast by adapting the colour tone of the picture according to the content on the screen.

The type of coating used on the TV screen.

— Matte. Historically, the first type of coating for LCD screens, which is often found today. Screens with such a coating generally have average characteristics of brightness, saturation and colour reproduction quality, in terms of these indicators they are inferior to glossy counterparts. However, the matte coating has one important advantage: it has virtually no glare from ambient light. In some situations, this can be an important advantage — for example, if the TV is installed opposite the window. And for some users it is more pleasant to look at the screen without glare, albeit relatively dim.

— Glossy. A coating designed to improve the brightness and colour quality of the visible image compared to matte screens. The creators have managed to achieve this goal: "glossy" screens really provide rich, vibrant colours and a brighter image. The key disadvantage of such screens is the appearance of glare from ambient light on them — this can ruin the whole viewing experience. Because of this, the classic glossy coating is practically not used today, anti-glare solutions have taken its place (see below).

— Glossy (anti-glare). Modification of the glossy coating, created, as the name implies, in order to eliminate the main drawback of the classic gloss — glare from external lighting. This is not to say th...at such screens do not glare at all, but there are much less reflections on them than on ordinary glossy ones. As for the image quality, it is at least not much worse, and often even better (especially since such coatings are constantly being improved). Thanks to all this, most modern TVs of all price categories are equipped with anti-glare screens.

The maximum brightness of the image provided by the TV screen.

The image on the screen should be bright enough so that you do not have to strain your eyes unnecessarily to view it. However, too high brightness is undesirable — it will also lead to fatigue. The optimal brightness level depends on the surrounding conditions: the more intense the ambient light, the brighter the TV screen should be. So, on a sunny day, the screen may have to be “turned up” to the maximum, and in the evening, in dimmed light, a relatively dim image will be more comfortable. In addition note that large screens require higher brightness, since they are designed for a greater distance from the viewer.

Thus, the higher the number in this paragraph, the greater the margin of brightness this model has, the better it will show itself in intense ambient light. The lowest indicator sufficient for more or less comfortable viewing in any conditions is 300 cd/m² for models with a diagonal of up to 32", 400 cd/m² for models in the range of 32 – 55" and 600 cd/m² for large screens of 60" and more. In this case, the brightness margin anyway will not be superfluous. But with lower indicators, you may have to darken the room somewhat for comfortable viewing.

The level of static contrast provided by the TV screen.

Contrast in a general sense is the ratio in brightness between the brightest whites and the darkest blacks that the screen can produce. Other things being equal, the higher the screen contrast, the better the quality of colour reproduction and detail, the lower the likelihood that it will be impossible to see details in too bright or too dark areas of the image. Static contrast, on the other hand, describes the maximum difference in brightness that can be achieved within one frame without changing the brightness of the image — this is its difference from dynamic contrast (see below).

The values of static contrast are much lower than those of dynamic, but this characteristic is the most "honest". It is on it that the properties of the image seen on the screen at a particular moment depend, it is describes the basic properties of the screen, without taking into account the software tricks provided by the manufacturer in the hardware of the TV.

The response time can be described as the maximum time required for each pixel of the screen to change brightness, in other words, the longest time from the receipt of a control signal to the pixel until it switches to the specified mode. The actual switching time may be less — if the brightness changes slightly, it can be calculated in microseconds. However, it is the longest time that matters — it describes the guaranteed response speed of each pixel.

First of all, the frame rate is directly related to the response time (see the relevant paragraph): the lower the response time, the higher the frame rate can be provided on this sensor. However, the actual frame rate may be less than the theoretical maximum, it all depends on the TV. Also note that the overall image quality in dynamic scenes depends primarily on the frame rate. Therefore, we can say that the response time is an auxiliary parameter: the average user rarely needs this data, and in the specifications they are given mainly for advertising purposes.

The highest frame rate supported by the TV.

Note that in this case we are talking specifically about the screen’s own frame rate, without additional image processing (see “Index of dynamic scenes”). This frequency must be no lower than the frame rate in the video being played - otherwise there may be jerks, interference and other unpleasant phenomena that degrade the quality of the picture. In addition, the higher the frame rate, the smoother and smoother the movement in the frame will look, and the better the detail of moving objects will be. However, it is worth noting here that playback speed is often limited by the properties of the content, and not by the characteristics of the screen. For example, films are often recorded at a frequency of only 30 fps, or even 24 - 25 fps, while most modern TVs support frequencies of 50 or 60 Hz. This is enough even for viewing high-quality content in HD resolutions (speeds above 60 fps in such video are extremely rare), but there are also “faster” screens on the market: 100 Hz, 120 Hz and 144 Hz. Such speeds, as a rule, indicate a fairly high class of the screen; they also often imply the use of various technologies designed to improve the quality of dynamic scenes.

The IMAX Enhanced Seal of Conformity is awarded to televisions that meet the video device certification requirements of IMAX Corporation. It applies to streaming and Blu-Ray content shot with IMAX cameras or processed using special DMR (Digital Media Remastering) software. To qualify for IMAX Enhanced certification, your TV must have 4K resolution, 10-bit color, support HDR10 and HDR10+, and DTS:X audio. As a result, viewers get the opportunity to enjoy the immersive effect of an IMAX cinema at home.

The nominal power of the sound produced by the TV's sound system.

The larger the screen and the greater the estimated distance to the viewer, the more powerful the sound system must be in order to be heard normally. Manufacturers take this moment into account, moreover, most often they also provide a solid volume margin. So if a TV is bought for home viewing in a quiet, calm environment, you can not pay much attention to the sound power: it is guaranteed to be enough for such a usage. It makes sense to specifically look for models with high-power speakers for a noisy environment — for example, a cafe or other public space. Detailed recommendations on this matter can be found in special sources, but here we note that even in such cases, connecting external speakers can be a good alternative.

The presence of a subwoofer as part of the TV sound system.

A subwoofer is a specialized speaker for bass and ultra-low frequencies. It makes the sound richer in the bass, which is especially useful when watching adventure films with appropriate sound effects (bumps, explosions), as well as concerts. It should noted that the specifications of built-in subwoofers are usually much more limited than those of external ones; so don't expect cinema-like bass from a TV audio system. However, the advantage in bass quality for such TVs (compared to models without a subwoofer) will still be noticeable.