Comparison Vector Optics Matiz 2-7x32 Duplex vs Hawke Vantage 2-7x32

The offset is the distance between the eyepiece lens and the exit pupil of an optical instrument (see "Exit Pupil Diameter"). Optimum image quality is achieved when the exit pupil is projected directly into the observer's eye; so from a practical point of view, offset is the distance from the eye to the eyepiece lens that provides the best visibility and does not darken the edges (vignetting). A large offset is especially important if the sight is planned to be used simultaneously with glasses — after all, in such cases it is not possible to bring the eyepiece close to the eye, and it must be at some distance from the glasses so as not to hit the glass due to recoil.

The diameter of the area visible through the sight from a distance of 100 m — in other words, the largest distance between two points at which they can be seen simultaneously from this distance. It is also called "linear field of view". This indicator is more convenient for many users than the angular field of view (the angle between the lines connecting the lens and the extreme points of the visible image) — it very clearly describes the capabilities of the device.

In sights with magnification adjustment (see above), both the entire range of width — from maximum to minimum — or only one value of this parameter can be indicated. In the latter case, the largest width of the field of view is usually taken, at the minimum magnification.

A type of coating used in scope lenses. Anyway, we are talking about the so-called antireflection coating, which is the thinnest film (single or multilayer) on the surface of the lens in contact with air. The properties of this film are chosen in such a way as to minimize the reflection of light from the glass surface. The meaning of this function is not so much to reduce the brightness of glare that can unmask the shooter, but to increase the light transmission of the optics and, accordingly, the quality of the image visible through it.

Modern sights can be equipped with the following types of coatings:

— Illuminating. In this case, the simplest option is implied — an incomplete single-layer coating. The term "incomplete" means that not all lens surfaces are coated (although there may be several coated surfaces). Such enlightenment is inexpensive, however, the image quality is relatively low — in particular, because a single-layer film is most effective only for a part of the visible colour spectrum.

— Full illumination. Fully coated means that all surfaces of the lenses that come into contact with air have a special coating; in this case it is single layer. Such a coating is more expensive than a simple anti-reflective coating, but the quality of the “picture” when using it is higher, because. light distortion at the transitions between glass and air is minimized.

— Multi-layered illuminating. Incomplete AR coating (see above)...using multilayer films. Thanks to multiple layers, the anti-reflective coating covers the entire visible spectrum, which allows you to achieve a brighter image with less colour distortion compared to single-layer coatings; However the price of such devices is higher.

— Full multilayer enlightenment. The most advanced option: multilayer coating on all lens surfaces used in the design of the sight. Features of full and multi-layer coating are described separately above. Here we note that their combination is typical for high-class sights, because. it provides the highest quality image, but it is not cheap.

The weapon class that this scope can be used with.

Different classes of weapons differ in the energy of the shot and, accordingly, the recoil force that the sight must endure without consequences. It is the maximum allowable energy of the shot (muzzle energy) that in this case is the main criterion for classifying the sight into one of the categories: light pneumatics, rifles and shotguns, large caliber. It is worth saying that such a division is somewhat arbitrary — see details in separate paragraphs; here is their detailed description:

— Lightweight pneumatics. Sights designed for weapons that practically do not give recoil — such as air PCP rifles, spring-piston “breaks” with muzzle energy up to 7.5 J, carbines chambered for Flaubert, as well as airsoft drives. Such models are definitely not suitable for firearms: they do not tolerate even the recoil from small-caliber rifles, not to mention more serious use. And even pneumatics have their limitations — in particular, powerful (more than 7.5 J) spring-piston models give significant returns with strong vibrations, and in pistols with the Blow-back system, noticeable concussions occur not because of the shot itself, but from -for the work of automation. So it is better to equip these types of weapons with more durable and reliable sights.

— Rifles and shotguns. Sights that can be used with...rifles of small and medium calibers, as well as smoothbore weapons (shotguns). They have a solid construction that allows them to endure rather strong recoil and accompanying vibrations without consequences, but the specific restriction on the allowable muzzle energy (and, accordingly, the calibers and ammunition used) may be different. However, scopes in this category are usually able to safely carry at least 2500 J — this is enough for rifled calibers 5.45x39, 7.62x39 and .223, as well as for 12-gauge rifle cartridges with a standard weight of gunpowder. And in many models, the maximum allowable energy can reach 3500 J and even 4000 J (the smallest values \u200b\u200bnecessary for full-fledged use with .308 and 7.62x54R calibers, respectively). At the same time, for reinforced magnum ammunition, as well as for some powerful (though not large) calibers, such a sight may still not be enough.

— Large-caliber. The most durable and reliable sights, designed for muzzle energy of 4000 J and above. Because of this, they can be used even with large-caliber firearms, as well as with some powerful calibers that are not formally large — for example, .300 Win and .338 Lapua Magnum. The specific restriction on muzzle energy, again, may be different, but if you are looking for a sight for a caliber more powerful than 7.62x54R or for reinforced rifle ammunition like 12x76, you should definitely pay attention to this category.

Separately, it is worth noting that “firearm” sights, even quite durable and reliable, are not recommended to be installed on pneumatics with a spring-piston mechanism or a gas spring. The fact is that such rifles have a specific recoil, directed forward rather than backward, moreover, giving sharp vibrations in different directions; and although the force of such recoil is low, it can still adversely affect the sight, which was not originally designed for it.

The type of mount supplied with the scope.

For normal mounting on a weapon, this mount must match the type of seat for the scope. The most popular types of mounts nowadays are on the Weaver / Picatinny rail and on the dovetail ; branded latches are noticeably less common, and some sights are supplied without mounts at all — this allows you to choose the option at your discretion. Here is a detailed description of specific options:

— On the Weaver / Picatinny rail. Fastening on a standard bar (“rail”) Weaver or Picatinny rail. It is considered the Western standard for installing a weapon body kit, but nowadays it is widely used around the world. It is worth noting that these types of slats, although similar in design, are not the same. They both have a T-shaped profile and transverse slots that allow you to securely fix the installed accessory in the chosen place, but differ in the size and location of these slots: they are wider in Picatinny rails and have a standard distance between centers. In fact, this leads to the fact that accessories for Weaver rails can easily fit on Picatinny rails, but not vice versa. In addition, Picatinny is considered more of a military standard, and civilian weapons are equipped mainly with Weaver rails. Thus, most of the complete rail mounts found among modern sights are designed specifi...cally for the Weaver rail, as it is more common and universal. However, exceptions are possible, so this nuance needs to be specified separately.

— "Dovetail". The seat of this type has a cross-sectional view of an inverted trapezoid, and the mount provides protrusions on both sides, which, when the sight is installed, “cover” this trapezoid. This type of mount is found mainly in air and sporting rifles, as well as in hunting weapons of a classic design. In the latter case, this choice is also due to aesthetic considerations — these mounts look neater than the gear "rails" of Weaver and Picatinny rails.

— Firm. Various specific fastenings not related to the standards described above. Often they are made not just for the products of a particular brand, but also for strictly defined models of weapons; one of the characteristic examples is the original seat on the high-end "sniper" Blaser R93. Branded devices can have a rather original design — for example, in some collimators for shotguns, a plate is used that is fixed between the butt and the receiver. In general, due to limitations in application, such fasteners are usually provided not as the only option, but as one of the options, in addition to the bar and/or dovetail.

Separately, it is worth touching on situations where several types of mounts are indicated in the characteristics of the sight at once. Most often this means that this model is available in different configurations, but there are other, more specific options — the presence of several types of mounts in the kit at once, an adapter from one type to another, or even a universal retainer that is also compatible with Weaver / Picatinny rails, and with a dovetail. Such details in each case should be clarified separately.

The country of origin of the brand under which the product is sold. Nowadays, the sights market is mainly represented by brands from such countries (in alphabetical order): Belarus, Great Britain, Germany, Spain, Lithuania, USA, Japan. However, there are other options as well.

There are many stereotypes about how the origin of a particular country affects the quality; however, nowadays, they have practically no basis. First, the origin of the brand is indicated either by the actual place of origin of the company, or by the country in which its headquarters is located; in both cases, this country does not always coincide with the country where the production is located and where the device was actually manufactured. For example, it is quite normal for the products of an American or German brand to be manufactured in Taiwan or Turkey. Secondly, the actual quality of a product is primarily affected by how it is positioned in the market and how carefully the manufacturer ensures quality control. As a result, paying attention to the "homeland" of the brand makes sense only when you fundamentally want or do not want to support a company from a certain country; in other cases, it is worth focus primarily on the reputation of a particular...manufacturer.

The total length of the sight.

This parameter is important primarily for optical sights (see "Type"). Such devices can be quite large — from 20 – 30 cm in the most compact models up to 40 cm or more ; and the distance from the eyepiece to the eye when aiming must be strictly defined. So before buying, it's ok to clarify whether it will be possible to correctly place the selected model on the weapon. But collimators, even the largest ones, are very compact, usually there are no problems with their installation, so in such models the length does not play a special role.