Comparison Lenovo V15 G2 ALC [82KD002RRA] vs HP 15-ef2000 [15-EF2126WM 4J771UA]

The contrast of the screen installed in the laptop.

Contrast is the largest difference in brightness between the lightest white and darkest black that can be achieved on a single screen. It is written as a fraction, for example, 560:1; while the larger the first number, the higher the contrast, the more advanced the screen is and the better the image quality can be achieved on it. This is especially noticeable with large differences in brightness within a single frame: with low contrast, individual details located in the darkest or brightest parts of the picture may be lost, increasing the contrast allows you to eliminate this phenomenon to a certain extent. The flip side of these benefits is an increase in cost.

Separately, we emphasize that in this case only static contrast is indicated — the difference provided within one frame in normal operation, at constant brightness and without the use of special technologies. For advertising purposes, some manufacturers may also provide data on the so-called dynamic contrast — it can be measured in very impressive numbers (seven-digit or more). However, you should focus primarily on static contrast — this is the basic characteristic of any display.

As for specific values, even in the most advanced screens, this indicator does not exceed 2000: 1. But in general, modern laptops have a rather low contrast ratio — it is assumed that for tasks that require more advanced image characteristics, it is more...reasonable to use an external screen (monitor or TV).

Laptop display certification for safe blue light emission levels and panel flicker rates. The presence of a TÜV Rheinland certificate confirms that the screen is comfortable for the eyes.

TÜV Rheinland is a large international concern headquartered in Cologne, Germany, providing a wide range of audit services. The company's specialists have developed and approved a number of tests for the compliance of the screens of mobile devices, monitors and TVs with the required level of eye protection from the harmful effects of display radiation on the user's vision on the other side of the screen. The authoritative opinion of TÜV Rheinland is respected in the tech community. Certificates from this body are issued to successfully tested electronics for the implementation of blue light filtering and screen flicker suppression technologies.

The result shown by the laptop processor in 3DMark06.

This test is primarily focused on testing performance in games — in particular, the ability of the processor to process advanced graphics and artificial intelligence elements. Test scores are reported as scores; the higher this number, the higher the performance of the tested chip. Good 3DMark06 results are especially important for gaming laptops.

The result shown by the laptop processor in the Passmark CPU Mark test.

Passmark CPU Mark is a comprehensive test that is more detailed and reliable than the popular 3DMark06 (see above). It checks not only the gaming capabilities of the CPU, but also its performance in other modes, based on which it displays the overall score; this score can be used to fairly reliably evaluate the processor as a whole (the more points, the higher the performance).

The total number of slots for RAM modules provided in the laptop; in fact — the maximum number of slats that can be installed simultaneously in this model.

Features for upgrading RAM directly depend on this indicator. So, in low-cost models, there is often only 1 slot, and the only upgrade option is to replace the "native" bar. In more advanced devices, two or even four slots may be provided, while some of them may be free in the initial configuration.

A special case is embedded RAM; it is more compact and cheaper than removable modules, but does not imply replacement at all. At the same time, in some laptops, the “RAM” is only built-in, in others it can be supplemented with one or even two slots for interchangeable strips.

The connection interface used by the M.2 SSD installed in the laptop (see "Drive type").

One of the features of the M.2 connector and drives for it is that they can use two different connection interfaces: PCI-E (in one form or another) or SATA. We emphasize that this paragraph indicates the data of the SSD module; the connector itself may provide other interface options, including more advanced ones — see "M.2 connector interface" (for example, a drive with a PCI-E 3.0 2x connection can be placed in a connector that also supports the faster PCI-E 4.0 4x). However, anyway, the connection connector usually allows you to realize all the features of the installed drive; so this item allows you to quite reliably evaluate the capabilities of the standard M.2 module.

As for specific interfaces, nowadays you can mainly find the following options:

— SATA 3. The SATA interface was originally designed for traditional hard drives. The third version of this interface is the latest; it provides data transfer rates up to 600 Mbps. This is significantly less than PCI-E, and in general, very little by the standards of SSD drives. Therefore, M.2 connection using SATA is typical mainly for low-cost entry-level modules. However, even these media are generally faster than most HDDs.

— PCI-E. Universal interface for connecting internal peripherals. Provides generally faster speeds than SATA, making it better suited for SSD modules: theoretically, PC...I-E allows you to realize the full potential of SSDs, even the fastest. In fact, the supported data transfer rate may be different — depending on the version of the interface and the number of lines (data transmission channels). Here are the options most relevant for modern laptops:

• PCI-E 3.0 2x. Connection using 2 lanes PCI-E version 3.0. This version provides speeds of about 1 GB/s per line; respectively, two lines give a maximum of just under 2 GB / s.
• PCI-E 3.0 4x. Connection using 4 lanes PCI-E version 3.0. Provides a maximum speed of about 4 GB / s.
• PCI-E 4.0 4x. Connection using 4 lanes PCI-E version 4.0. In this version, the throughput, compared to PCI-E 3.0, has been doubled — thus, 4 lines give a maximum speed of about 8 MB / s.

Note that in the case of M.2 connectors, different PCI-E variations are usually quite compatible with each other — except that the connection speed when working with a "non-native" connector will be limited by the capabilities of the slowest component. For example, when connecting a PCI-E 3.0 4x SSD module to a PCI-E 3.0 2x slot, this speed will correspond to the capabilities of the connector, and when connected to PCI-E 4.0 4x, to the capabilities of the drive.

The size of the M.2 SSD module (see "Drive Type") installed in the laptop. Specified in the format "width x length".

This parameter primarily allows you to evaluate the amount of space allocated for the drive, and the possibility of replacing it with a module of a different size. It is worth noting here that the M.2 standard itself allows several options for length and width, but boards with a width of 22 mm are most widely used. The length of such a board usually corresponds to one of the standard options: 30 mm, 42 mm, 60 mm, 80 mm and 110 mm.

In general, the installation of a shorter module of the same width (for example, 22x42 mm instead of 22x60 mm) does not cause problems, but the possibility of using larger components should be clarified separately — not every case allows the installation of M.2 drives with a larger one than the standard module , length. As for specific dimensions, the most common in modern laptops is M.2 22x80 mm SSDs: this size is guaranteed to allow you to change the “native” drive to almost any 22 mm standard module (except for the largest, 22x110 mm — and even for them there can be a place ). There are also smaller sizes — 22x60 mm, 22x42 mm and even 22x30 mm — but much less frequently. And here it is worth saying that the shorter the length of the SSD module, the smaller its capacity, usually.

Note that modern laptops also use M.2 modules of a different width — usually 16 mm with a length of 20 mm (16x20 mm). H...owever, this is a very rare option.

The presence in the laptop of an additional compartment for an internal drive of the form factor 2.5 ".

Usually, to install or remove a drive in such a bay, it was not necessary to disassemble the entire laptop — just remove the cover or remove the plug. As for 2.5", this is the traditional form factor for hard drives (HDD) for "laptop" purposes, although other types of media (SSD and SSHD — see "Media Type") can be produced in this format. For connection 2.5 "storage drives normally use the SATA connector — it is not as fast as more modern standards like M.2 PCI-E (see "Drive Interface"), however, it is cheaper, and for HDD this connector is quite enough.

Thus, the presence of an additional 2.5" bay allows you to quickly and cost-effectively increase the total volume of laptop drives.

A device for working with removable memory cards. Usually, it looks like a characteristic slot right on the laptop case, into which the media is inserted. There are different standards for memory cards, a list of compatible standards is indicated in the note to this item. It is worth noting here that for modern laptops it is almost mandatory to support the SD format and its modifications — SD HC, often also SD XC; other options may also be envisaged, but they have not received such distribution. Anyway, this feature is convenient because memory cards are widely used in other types of electronics: for example, SD is the generally accepted standard in digital cameras, and microSD (compatible with SD slots through simple adapters) is used in smartphones. Accordingly, the presence of a card reader greatly facilitates the exchange of data between a laptop and external devices.