Comparison Bridgestone Blizzak LM001 225/50 R18 95H Run Flat BMW/Mini vs Bridgestone Blizzak DM-V3 225/60 R18 100S

Tyre aspect ratio. This parameter is usually expressed as a percentage of the width, since it is not the height itself that is of practical importance, but its ratio with the nominal section width.

In general, the lower the ratio, the more stable the tyre, the better it is suitable for high-speed driving on flat roads. Higher ratio, in turn, work better on rough surfaces and over obstacles, making them good for bad roads and off-road. If we talk about specific numbers, nowadays, the following options are spread on the market:

— Low profile tyres: 25%, 30%, 35%, 40% ;
— Medium profile : 45%, 50%, 55%, 60% ;
— High profile : 65%, 70%, 75%, 80%, 82%, 85%, and 90% or more.

The maximum weight load that the tyre is able to carry. It is denoted by a conditional figure, each of which corresponds to a certain value:

66 - 300 kg, 67 - 307 kg, 68 - 315 kg, 69 - 325 kg, 70 - 335 kg, 71 - 345 kg, 72 - 355 kg, 73 - 365 kg, 74 - 375 kg, 75 - 387 kg, 76 - 400 kg, 77 - 412 kg, 78 - 425 kg, 79 - 437 kg, 80 - 450 kg, 81 - 462 kg, 82 - 475 kg, 83 - 487 kg, 84 - 500 kg, 85 - 515 kg, 86 - 530 kg, 87 - 545 kg, 88 - 560 kg, 89 - 580 kg, 90 - 600 kg, 91 - 615 kg, 92 - 630 kg, 93 - 650 kg, 94 - 670 kg, 95 - 690 kg, 96 - 710 kg, 97 - 730 kg, 98 - 750 kg, 99 - 775 kg, 100 - 800 kg, 101 - 825 kg, 102 - 850 kg, 103 - 875 kg, 104 - 900 kg, 105 - 925 kg, 106 - 950 kg, 107 - 975 kg, 108 - 1000 kg, 109 - 1030 kg, 110 - 1060 kg, 111 - 1090 kg, 112 - 1120 kg, 113 - 1150 kg, 114 - 1180 kg, 115 - 1215 kg, 116 - 1250 kg, 117 - 1285 kg, 118 - 1320 kg, 119 - 1360 kg, 120 - 1400 kg, 121 - 1450 kg, 122 - 1500 kg, 123 - 1550 kg, 124 - 1600 kg, 125 - 1650 kg, 126 - 1700 kg, 127 - 1750 kg, 128 - 1800 kg, 129 - 1850 kg, 130 - 1900 kg, 131 - 1950 kg, 133 - 2060 kg.

While choosing according to this indicator, it is worth considering not only the maximum weight of the car for which tyres are going to buy, but also the distribution of weight along the axles. With passenger cars, everything is simple — the weight is distributed approximately equally, so to determine the load on each wheel, it is enough to divide the maximum mass of the car by 4 (the number of wheels). H...owever, in minibuses, light trucks and SUVs, the situation is different: the weight distribution can be unequal, so you should refer to the manufacturer's documents or other special sources to calculate the load on each wheel.

Anyway, the load index must not be exceeded — this creates the danger of an accident. In fact, the wheel load should be at least 10 – 15% below the maximum, this will give an additional guarantee in case of abnormal loads. Also note that in some high-speed tyres, with the speed maximum approaching, the permissible load decreases: for example, for tyres with the V index (see "Speed rating") with speed over 210 km/h, it is recommended to reduce the load by 3% for every next 10 km/h increase in speed, similar recommendations apply to models with indexes W and Y. These details are usually described in the manufacturer's documentation and other special sources.

The speed rating that the tyre corresponds to.

This indicator determines the maximum speed that tyre is allowed to operate. It is designated by the letters of the Latin alphabet, each of which corresponds to a certain speed limit:

F — 80 km/h; G — 90 km/h; J — 100 km/h; K — 110 km/h; L — 120 km/h; M — 130 km/h; N — 140 km/h; P — 150 km/h ; Q — 160 km/h ; R — 170 km/h ; S — 180 km/h ; T — 190 km/h ; U — 200 km/h ; H — 210 km/h ; V — 240 km/h ; W — 270 km/h ; Y — 300 km/h ;

The maximum permitted speed must not be exceeded — this creates the risk of an accident. However, there are other rules associated with choosing a tyre by this factor. So, ideally, the actual driving speed should be at least 10 – 15% lower than the speed rating of the installed tyres — this will give an additional guarantee in case of emergency situations. In addition, in some tyre models, as the speed approaches the maximum, the upper limit of allowable load is reduced; see “Load Index” for details.

The shape of the tyre tread pattern:

— Directional. Pattern with a characteristic V-shape. Among other things, such rubber is considered to be especially effective on wet surfaces — in rain, on snow, with an abundance of melt water, etc.: the pattern provides effective water drainage, reducing the risk of hydroplaning and increasing grip. Also, these tyres are well suited for high-speed sports cars (although, of course, their speed rating and specialization may be different). When installing directional tyres, the direction indicated by the manufacturer must be kept.

— Symmetric. The pattern without signs of directionality is the same both on the outer and on the inner part of the tread. These tyres are easier to manufacture than directional or asymmetric tyres, and are generally cheaper, while still having good performance on a flat and dry surface. In addition, symmetric tyres are as simple as possible to install, they do not need to follow the direction. However, for hard conditions, particularly wet weather, they are poorly suited. So, typically, such tyres are designed mainly for city cars used on short trips on relatively high-quality roads.

— Asymmetric. Tyres with a different pattern inside and outside the tread. Each of these parts plays a role: the inner part provides water evacuation and reduces the risk of aquaplaning, while the ou...ter part provides the necessary rigidity for manoeuvrability and stability. While installing, you need to take into account the location of the outer and inner sides, they usually have the appropriate marking. Asymmetric tyres are considered the most advanced, although, of course, the actual characteristics and cost of such products may vary, depending on the brand and the general level. Such tyres are designed mainly for cars of medium and top levels; they are often supplied as factory equipment for advanced cars.

A technology that allows the tyre to maintain its performance even being flat. If a conventional tyre fails after a maximum of a couple of kilometers with a loss of pressure, then you can drive several tens of kilometers on RunFlat tyre without any problems — this is usually enough to get to the nearest tyre service. Similar properties are achieved due to the reinforced structure, particularly the increased rigidity of the sidewalls. Different manufacturers may use names other than Run Flat for this technology, such as Flat Run or Zero Pressure.

We note separately, that tyres with this feature can only be used on vehicles equipped with a tyre pressure monitoring system. Without such a system, it is likely that the driver will not notice tyre damage immediately — and this is fraught with several unpleasant consequences at once. Firstly, you can miss the time needed to correct the situation — as a result, the resource of a flat tyre may not be enough to normally get to the workshop or service station. Secondly, driving on a run flat tyre requires slowness and special care, driving in a normal style on such a tyre can lead to loss of control.

The rolling resistance rating that the tyre corresponds to. The higher this figure, the lower the resistance, the less fuel is spent to overcome it and the more economical the tyre is. Efficiency indices are denoted by letters of the Latin alphabet in descending order of efficiency: A(highest efficiency), B, C, D, E, F, G(lowest efficiency).

With other things being equal, more economical tyres tend to cost more, but the difference is offset by fuel economy.

An index that determines the overall performance of a tyre on wet pavement. Lettered from A(highest) to G(lowest); intermediate options, respectively — B, C, D, E and F.

The higher this indicator, the stronger the tyre grips to the wet road, the more efficient and safer it will be in difficult weather conditions. At the same time, it is worth noting that a low grip index does not mean unsuitability for driving in rain or snow — you just need to be more careful using such tyres. Conversely, a high index does not relieve the driver of the need to be careful in difficult weather conditions.

The average noise level created by a tyre while driving. The lower this indicator, the more comfortable this model will be, the less additional noise it will create.

Note that EU rules provide 3 categories of tyres in terms of noise. “Quiet” are considered models with an index of up to 68 dB, “medium” — 68 – 71 dB, “loud” — 72 dB and above.

Vehicle manufacturer's recommendations for ideal tyres for a specific vehicle model. Homologated tyres take into account the technical and design features of machine, up to factory suspension settings, thanks to which it is possible to unleash the full potential of the “iron horse”. It is recommended that tyres approved by the manufacturer be installed only on the wheels of suitable vehicles, and in some cases, without the use of homologated tyres, machine risks losing the warranty. Tyre sharpening for a specific brand and model of car is indicated by specialized homologation markings.

On the shelves of tyre stores, homologated tyres are most often presented for the following car brands: Audi(including Audi RS, Alfa Romeo, BMW / Mini, Ferrari, Mercedes-Benz(including Mercedes AMG), Maserati, Porsche, Tesla, Volvo, Volkswagen.