United Kingdom
Catalog   /   Tools & Gardening   /   Power Tools   /   Power Saws

Comparison STIHL MS 261 C-MQ 40 vs STIHL MS 260 38

Add to comparison
STIHL MS 261 C-MQ 40
STIHL MS 260 38
STIHL MS 261 C-MQ 40STIHL MS 260 38
from £799.00 
Outdated Product
from $395.20 up to $499.96
Outdated Product
TOP sellers
Product typechainsawchainsaw
Typeportableportable
Power sourcepetrol enginepetrol engine
Motor
Engine size50.2 cm³50.2 cm³
Power3000 W2600 W
Power4.08 hp3.5 hp
Idle speed2800 rpm2800 rpm
No load speed14000 rpm
Cutting equipment
Bar/blade size400 mm380 mm
Chain pitch0.325 "0.325 "
Features
Features
chain brake
anti-vibration system
chain brake
anti-vibration system
General
Noise level116 dB113 dB
Fuel tank volume0.5 L0.46 L
Oil tank volume0.27 L0.29 L
Weight
5 kg /without cutting equipment/
4.8 kg
Added to E-Catalogoctober 2017december 2009

Power

Saw motor power in watts. For petrol tools (see "Power Source"), horsepower is additionally indicated, see below for details.

The higher the power, the better the tool is suitable for voluminous work and hard materials, the greater the depth of cut it can provide and the easier it can cope with significant loads. In addition, for different types of saws and different types of materials, the actual power values \u200b\u200bcan also be different. For example, a power of 2.5 – 3 kW is actually the limit for chain saws, but in chain saws this is an average figure, among such tools there are models of 3 – 4 kW and even more. Detailed selection recommendations for various cases can be found in special sources.

Power

The power of the saw engine expressed in horsepower (hp). This designation is traditionally used in gasoline models (see "Power Source") along with watts; 1 HP ≈ 735 W.

For more information about power, see the paragraph of the same name above.

No load speed

The highest speed that the saw engine is capable of delivering in normal operation.

We emphasize that this parameter should not be confused with the maximum disk speed (see below) — here we are talking exclusively about the speed of rotation of the motor shaft. It can be specified for all types of saws, not only for models using discs. However, in general, engine speed is more of a reference than really significant information. In fact, it is needed mainly for some specific tool maintenance tasks; when choosing, it is better to focus on indicators that are more “close to life” — engine power, cutting depth, chain / tape speed or disk speed, etc.

Bar/blade size

The largest tyre size (in chain saws) or disc (in circular saws and some others, see "Device") that is allowed for this tool. Tyres are sized by working length, rims by diameter.

A larger bar/wheel allows for deeper cuts but requires more powerful motors. Therefore, this parameter cannot be exceeded — this can lead to an overload of the engine with all the corresponding troubles. However, in many models with a disc it is physically impossible to install a nozzle with a diameter larger than the maximum allowable.

Also note that saws with similar bar/blade sizes may differ in maximum depth of cut (mostly due to differences in design or power). As for the specific dimensions, they depend on the type of saw (see "Device"). For example, large discs of 450 – 500 mm are found exclusively in stationary chain saws, the maximum figure for cutting models is 400 – 450 mm, for trimming — 300 – 350 mm, and sizes of 500 – 550 mm or more clearly indicate that speech It's about a chainsaw chainsaw bar. Detailed recommendations regarding the choice of a tool for a given size can be found in special sources.

Noise level

The noise level produced by the saw during operation. Note that this parameter is rather approximate, because in fact, the “loudness of the work” depends not only on the tool, but also on the material being processed and the characteristics of the environment. Nevertheless, the data given in the characteristics make it possible to assess the comfort of working with the tool. The lower this indicator, the less discomfort the noise will cause, and at high values, even special hearing protection may be needed.

Note that the noise level is usually measured in decibels, and this unit is not linear: for example, a difference of 3 dB corresponds to a difference of 2 times, 10 dB — to 10 times. Therefore, it is easiest to evaluate the noise level using comparative tables. Here is a simplified version of such a table for the range in which modern saws operate:

70 dB — loud conversation of several people in close proximity;
75 dB — a cry in the immediate vicinity;
80 dB — truck engine, mechanical alarm ringing;
85 dB — loud scream;
90 dB — freight car at a distance of 7 – 10 m;
95 dB — subway car at a distance of 7 – 10 m;
100 dB — industrial shop;
110 dB — tractor engine;
120 dB — demolition hammer, thunder from a close lightning strike (pain threshold of auditory perception).

Fuel tank volume

The volume of the fuel tank in saws with a petrol engine (see "Power source"). A volume tank, on the one hand, allows the device to work for a long time without refueling, on the other hand, it seriously affects the weight and dimensions. The latter is not critical for stationary units (see "Type"), but it is very important for portable equipment — and the vast majority of chainsaws and power cutters are made portable. And taking into account the fact that refueling usually does not cause any particular difficulties, it does not make sense to equip hand tools with capacious tanks, therefore this volume is small in such saws.

Oil tank volume

The volume of the oil tank provided in the tool.

In this case, we mean a tank from which oil is supplied to the saw chain (see "Device") to lubricate it during operation. In general, this is a reference parameter that allows you to estimate how much oil is needed for one refueling of the tool.

Weight

The total weight of the tool. For petrol models (see "Power Source"), usually, dry weight is indicated, excluding fuel.

In general, it makes sense to pay attention to this parameter primarily when choosing a hand tool. At the same time, note that higher power, a more capacious battery or a capacious tank will inevitably affect weight. However, tools with similar characteristics can and do differ markedly in weight. And here it is worth considering that a lighter model will be more comfortable to work with, but weight reduction may affect reliability and/or cost. In addition, a more massive tool is more stable, it is not so prone to jerks under uneven loads. If we talk about specific numbers, then a weight of 3 kg or less is considered very light, 3–5 kg is relatively small, 5–7 kg is medium, 7–10 kg is significant, and some powerful tools (mainly gasoline) weigh and over 10 kg.

As for stationary saws, weight is of secondary importance for them — it mainly affects the ease of transportation.
STIHL MS 260 38 often compared