Comparison Dnipro-M DTC-200BC Dual vs AL-KO BC 400 B

The type of engine that drives the cutting tool of the lawn mower, and in self-propelled models, the device itself. At the moment, the following types of engines are used:

— Electric (mains). Mains powered motor. Its advantages are low noise level, low cost and ease of operation (no need to buy fuel and oil) and no emissions into the atmosphere. Among the shortcomings can be called a relatively small power and a short range, limited by the length of the power cord.

— Electric (battery). Electric motor powered by its own built-in battery. It has all the same advantages as a mains-powered motor; in addition, such devices are not limited in movement, since they do not require a network connection during operation. On the other hand, the battery life of battery lawn mowers rarely exceeds half an hour, the battery weighs a lot and takes a long time to charge, and the power of such devices is even lower than that of network ones (despite the fact that they are noticeably more expensive).

— Petrol. Gasoline internal combustion engine. The advantages of such engines, in comparison with electric ones, are independence from the mains connection and high power, which allows you to work with dense thick vegetation. On the other hand, gasoline engines are heavier, more expensive to run, require the purchase of fuel and lubricants, and emit exhaust gases into the...air.

— Diesel. A type of internal combustion engine. In terms of basic features, diesel engines are almost identical to those described above, but they also have their own characteristics. On the one hand, in such units it is easier to provide high power and good torque, so they are better suited for "heavy" tasks; and diesel fuel is cheaper than gasoline. On the other hand, diesel engines themselves are more expensive, heavier and more difficult to operate. Therefore, they are not particularly popular among lawn mowers, this option is found mainly in riders (see "Type"), where high power is more important than the mentioned disadvantages.

— Gas. A rare variety of internal combustion engines that use a propane-butane mixture of gas as fuel. Their advantages over gasoline units are economical consumption, high mowing performance, and a small amount of harmful emissions into the atmosphere. In addition, gas fuel reduces the load on the engine, which, in turn, prolongs its operational life. The reverse side of the coin is the need to fill the cylinder with liquefied hydrocarbon gases at specialized filling complexes or the frequent replacement of gas cartridges.

— Without engine(manual). Lawnmowers that are not equipped with any motors and use the muscular strength of the user — when working, it is necessary to push the device in front of you. The advantages of such a scheme are low cost (both the device itself and its operation), independence from fuel and electricity, and maximum environmental friendliness; disadvantages are the relatively low quality of work and the significant expenditure of physical strength.

The capture width provided by the unit, in other words, the width of the strip of land cultivated in one pass. In fact, this size corresponds to the width of the working nozzle.

The large working width is useful when processing large open spaces, as it allows you to finish the job in a small number of passes. On the other hand, for hard-to-reach places, relatively narrow tools are better suited, able to go where a wider unit will not fit. In addition, the width of the tool directly affects the weight and price.

In general, it makes sense to compare in terms of working width only units of the same type (see above). However, it is worth noting here that trimmers do not differ so much from each other — most models capture from 25 to 45 cm (and a wide processing band is provided by moving the nozzle from side to side). As for the other types, in the most modest models the capture width does not exceed 40 cm, in the heaviest and most powerful it can be 56 – 60 cm or even more(in mini tractors — up to 1.5 m).

The width (diameter) of the trimmer knife characterizes the size of the paddle knife (or saw blade). Such a nozzle has a smaller capture width than a fishing line, however, it allows you to mow more dense thickets, including shrubs.

The diameter of the fishing line supplied with the trimmer (more precisely, with a reel attachment, see "Tips").

In modern models, this parameter can be from 1 to 4 mm. At the same time, a thicker fishing line handles better with dense thickets, but it works rougher, the treated lawn is not particularly even, and for the effective operation of such a nozzle, a fairly powerful engine is needed. On the other hand, a fine line provides a clean and neat cut, but is not suitable for heavy vegetation and large stems. Thus, thick fishing line is usually equipped with powerful units designed for "launched" lawns with an abundance of thick stems. Thin, on the other hand, is found mainly in low-power electric trimmers with a lower engine location, designed for neat lawns with regularly cut grass.

We also recall that many trimmers have the ability to replace the standard reel with another one that differs in line thickness.

— Adjustment of an inclination of a bar. The ability to tilt the bar or the working head relative to the bar. The setting will come in handy for mowing grass in hard-to-reach places. Trimmers with this function are much more convenient to work under swings, benches and garden furniture. Also, by adjusting the inclination of the rod, you can adjust the grip of the trimmer to the height of the user.

- Telescopic rod. The possibility of increasing the length of the trimmer by lengthening the bar. Due to the design features, this solution is available only for models with a lower engine and helps to maximally adjust the device for a person of any height.

- Collapsible bar. The ability to disassemble the trimmer bar into several parts. This feature greatly simplifies storage and transport: it is easier to pack, carry and transport components folded side by side than a solid long rod. Theoretically, this design is less reliable than non-separable, however, trimmers are usually not subjected to such high loads that this is noticeable.

- Shoulder strap. Strap for carrying the trimmer on the shoulder - including during operation. This design significantly simplifies the operator's task and reduces fatigue: carrying on the shoulder is not as tiring as holding it in the hands of weight. Note that in models without a sho...ulder strap, it may be possible to purchase it separately; however, it is easier (and often cheaper) to buy a tool with this accessory right away.

— Restrictive bracket. The bracket acts as a limiter and is designed to protect high (necessary) vegetation from mowing. Those. you can put forward a small structural element at the base of the bar, which, approaching the bushes, will move them away, thereby not cutting them off. The bracket will also be appropriate when mowing a site with a fence, a decorative landscape with many elements that can be damaged during mowing, or they themselves can “shorten” the fishing line once again by breaking off its ends.

- Swivel head. Possibility of rotation of a working nozzle of a trimmer on a bar. Typically this function is used to change the cutting system from a horizontal position to a vertical position. Cutting in a vertical plane can be useful, for example, for leveling edges and forming borders on lawns.

- Edging roller. The roller is necessary for a neat "haircut" between the lawn and the sidewalk. It is found in models with a swivel head and is designed for more comfortable work. Since the device does not need to be suspended, it is much easier to frame flower beds, decorative elements on the lawn, borders, etc., relying on the roller.

- Support rollers. Special rollers mounted on the cutting head of the trimmer. Thanks to these rollers, you can rest the head on the ground and roll the tool in front of you - this is more convenient than carrying it "on yourself". Another advantage is that the rollers keep the working attachment at the same height, which means that mowing is as accurate as possible, almost like using a conventional lawn mower (with all the advantages of a trimmer). The main disadvantages of models with rollers are the high cost, as well as the increased weight, which makes it difficult to work “off the ground”.

Scheme of operation of an internal combustion engine installed on a lawn mower. Note that this division is relevant only for gasoline engines (see "Engine type") — diesel engines are extremely rare and are made only four-stroke.

— 2-stroke. The main advantages of two-stroke engines over four-stroke ones are the simplicity of the device and higher power with the same working volume, due to which such units are lighter, more compact and cheaper. On the other hand, they consume more fuel and are distinguished by a high level of noise, and such an engine needs to be filled with a mixture of gasoline and oil in the correct proportion, which complicates maintenance somewhat (there are separate refueling systems, but they are complex and expensive, which is why they are almost never used ). As a result, this option is found mainly among trimmers (see "Type"): it is there that small dimensions and weight are decisive, and the required power and fuel consumption are relatively low.

— 4-stroke. Engines of this type are somewhat more complicated and more expensive than two-stroke ones; in addition, to achieve the same power, they need more volume, which affects the size and weight. On the other hand, if the engine does not need to be "carried in the hands" (as is the case with trimmers), these points do not really matter; and the difference in price, thanks to the development of technology, is becoming less and less noticeable. With a...ll this, four-stroke engines are quieter and consume less fuel. As a result, almost all units where a relatively large and heavy internal combustion engine can be installed are equipped with this particular type of engine. And relatively recently, light and compact engines have appeared, suitable even for trimmers.

The size of the engine installed in the petrol or diesel model (see "Engine type"). Power directly depends on this indicator, however, only engines of the same type can be compared by volume (see "Type of internal combustion engine"). And even in the same type of units of the same power, the volume can be different. In such cases, note that a larger volume means more fuel consumption, but the engine itself may cost less than a smaller one.

The maximum speed that the engine in an electric mower can run at (see "Engine type").

It makes sense to compare according to this indicator only engines of the same power. In general, higher rpm improves performance but reduces torque. Conversely, a relatively slow engine will be inferior to a “fast” one in overall speed, but it will better cope with dense dense vegetation. So it’s worth choosing by engine speed, taking into account what is more important to you — speed or efficiency in difficult conditions.

Lawnmower engine power expressed in horsepower. The common unit of power these days is the watt, but gasoline and diesel engines (see "Engine Type") are traditionally referred to as hp. Some units are easy to convert to others: 1 hp. approximately equal to 735 watts.

In general, the more powerful the engine, the more performant the mower is and the better it handles with heavy work such as cutting thick grass, bushes, etc. On the other hand, high power has a corresponding effect on fuel consumption, as well as the weight and price of the engine. In addition, it should be taken into account that different types of mowers (see "Type") differ in terms of power requirements. For example, among trimmers there are many models with a capacity of 0.7 – 1.3 hp., for gasoline lawn mowers, the minimum power is already in the range of 1.3 – 2 hp., and for mowers, at least 2.5 hp is required. . So you can only compare units of the same type in terms of power. Detailed recommendations for choosing a mower depending on its type and features of the planned work can be found in special sources.