Comparison Voopoo Drag S Mod Pod vs Voopoo Drag Nano Pod Kit

Additional functions of the board provided in the electronic battery mod (see "Battery mod").

— Varivolt. Battery mods that allow you to adjust the voltage supplied to the atomizer. Due to this, the power supply changes and, accordingly, the heating power and the general vaping mode are regulated. At the same time, unlike the varivolt (see below), the voltage change in the varivolt is carried out only manually, regardless of the resistance of the atomizer. In fact, this means that if the user wants to get the same power on an atomizer with a different resistance, he will have to reconfigure the varivolt.

— Variwatt. Battery mods with the ability to automatically maintain the specified power supplied to the atomizer. An automated version of varivolts, which is able to automatically adjust to changes in the resistance of the atomizer. The voltage in the variatt is set for a specific resistance of the atomizer; if the resistance changes, then the electronics automatically sets the voltage at the output of the battery mod so that the power remains unchanged. Thanks to this, you can put heaters with different resistances on the battery pack without worrying about reconfiguring the power parameters — the variatt will independently select the desired voltage, keeping the intensity of soaring at the usual level. The main disadvantage of this option compared to...the varivolt is the relatively high cost, and compared to thermal control(see below), the need to choose the power experimentally, by trial and error.

— Variwatt + Varivolt. Battery mods capable of operating in two different modes — varivolt or variwatt, at the request of the user. These modes are described in more detail separately, and their combination in one battery pack can be useful for those who appreciate the advantages of vari-watt, but are not averse to experimenting with vari-volt as well.

— Thermal control + variatt. Battery mods that combine the variatt capabilities described above with the thermal control function. Thermal control allows you to monitor the temperature of the spiral, maintain it at an optimal level and turn off the power when approaching critical heating. The combination of these two adjustments is the most advanced option for today, in fact, eliminating the need for the vaper to manually select the optimal power settings. At the same time, the steam turns out to be pleasant to the taste (both due to its own temperature, and due to the fact that the probability of burning the wick is reduced to almost zero), and the battery charge is consumed in an optimal way. A serious drawback of thermal control, in addition to a rather high cost, is limited compatibility with atomizers: for this function to work correctly, a “head” with a coil made of nickel or titanium is required, and such models are relatively rare, and they are not cheap in themselves.

— Thermal control. Battery mods, the settings of which are limited only by thermal control. This function is described in more detail above; here we note that thermal control itself does not allow controlling the intensity of soaring, therefore this option has not received much distribution.

The volume of the liquid tank provided in the design of the atomizer. Note that this parameter can be specified even for squonk atomizers (see "Filling type"): although they work with an external tank, however, a certain amount of "liquid" can fit in the evaporator itself.

The larger the tank, the more liquid you can keep in an electronic cigarette and the less often you have to refill it. On the other hand, capacious tanks have the appropriate dimensions, and too large a tank would be inconvenient, and liquids are consumed relatively little even in one long session of soaring. As a result, a volume of more than 6 mL is already considered quite large for vapes, and in the smallest models this figure does not exceed 2 mL.

Also note that when choosing a tank capacity, manufacturers usually take into account the resistance of the spiral, the power of the battery (if it is included) and other parameters that affect the expected flow rate of the liquid. There is no hard dependency here, however, in general, more powerful atomizers are usually equipped with larger tanks.

— Upper. The traditional type of filling was initially quite popular, but now such atomizers are gradually giving way to bottom filling models. The main advantage of this option is the ability to pour liquid without turning the atomizer over and without removing the flask from the battery mod. However refilling usually requires disassembly — for example, unscrewing the cap with the mouthpiece.

— Lower. This option assumes that for refueling, you need to turn the atomizer upside down and pour liquid from the bottom side. At first glance, this procedure is less convenient than top filling, but it provides an important advantage for serviced heaters: if necessary, you can remove and rewind the base without draining the liquid from the tank. Note that squonk format drip atomizers are formally also refueled from below, however, they have their own specifics, therefore they do not belong to this category and are allocated separately; see below for details.

— Side. Refueling through a special hole in the side of the atomizer. Like the top one, this design allows you not to remove the flask from the battery mod; the opening usually opens and closes easily and quickly, without the need, for example, to unscrew the cap. This option is quite popular in baco drips (see "Type of atomizer"), althou...gh it is also found in other varieties.

— Squonk. A specific type of bottom filling used in models with drip atomizers (see "Type of atomizer"). These vapes have a rather large e-liquid reservoir installed in the battery mod, and each time you press a special button (or the elastic wall of the reservoir), the liquid is fed into the atomizer in small portions directly through the connector. This design eliminates the main drawback of drip atomizers — the need to constantly add liquid manually, "drop by drop": instead of the hassle of manual refueling, it is enough to periodically press the button. At the same time, most of these evaporators allow installation on a regular battery mod, without a squonk — for this, the kit provides a replaceable connector of a standard design, without a channel for supplying liquid; and on battery mods with a squonk, usually, you can put ordinary atomizers without restrictions. The disadvantages of this option can be somewhat higher cost than analogues with traditional types of refueling.

The type of blowing provided in the atomizer of an electronic cigarette.

This parameter is indicated by the location of the cells for the intake of air entering the evaporator. According to this criterion, lower, upper and side airflow are distinguished, here are their main features:

— Lower. The most popular option nowadays. Such popularity is primarily due to the fact that many vapers consider the “lower” vapor to be the most delicious. In addition, bottom blown atomizers are easier to maintain than "side" models, they are not so demanding on winding quality. The disadvantages of this option include an increased likelihood of leakage, including during liquid overflow; and the condensate, which is quite intensively formed at the air intakes, tends to flow down onto the battery mod. However, these points are not particularly critical.

— Upper. A format that has appeared relatively recently. In general, such an airflow conveys taste somewhat worse than the lower one, moreover, the steam turns out to be hotter; however, this point is largely subjective, and some users like this type of steam. The objective advantages of the “upper” atomizers include the minimum probability of overflow, the almost complete absence of condensate flowing onto the battery mod, and the absence of splashes even when using coils with very low resistance.

— Si...de. The type of blowing used mainly in "drips" (see "Type of atomizer"). If the bottom airflow gives the most delicious steam, then the side airflow is the most dense and saturated. This is achieved due to the fact that the air flows around the spiral as intensively as possible and captures the greatest amount of evaporation. In addition, the likelihood of liquid overflow and splash formation in such atomizers is very small, and with the right settings, the taste is transmitted almost as well as in the “lower” models. The main disadvantage of this option is the actual need for careful tuning and proper installation of the spiral — so that there are no blind spots on it. So side airflow is generally designed for experienced users; maintenance-free atomizers are an exception, but this format of operation is rarely used in them.

Also note that there are combined options for sale, for which two types of airflow are indicated at once. Here the specifics can be different. So, it is unrealistic to combine the upper and lower airflow in one evaporator, therefore this option is indicated only for sets of several atomizers with different types of airflow. But the side format of work may well be combined with the top or bottom — this allows you to combine the advantages of both options and provide saturated steam. On the other hand, the need for careful tuning for such devices is just as relevant as for "pure" side ones.

Systems that are activated and give steam not with a button, but at the moment of puffing. This solution makes it easier to smoke, since it is not necessary to constantly hold the button. Plus , activation on a puff eliminates the likelihood of accidental pressing when carried in a pocket, bag, etc.

The smallest resistance of the heating coil of an electronic cigarette.

The meaning of this parameter will be different, depending on which part of the device is in question (see "Type"). So, for atomizers, this parameter is given if spare heaters are supplied in the kit — accordingly, it is indicated for the “head” with the lowest resistance. For a battery mod, this is the smallest resistance that can be connected to it. And in starter kits, the minimum resistance is also usually indicated by the battery mod; low-resistance "heads" in such cases may or may not be included in the delivery.

Anyway, data on the minimum resistance is important in the mutual selection of an atomizer and a battery mod (including when creating custom windings) — connecting an atomizer with too low resistance is fraught with overloads and various unpleasant consequences, up to fire. However, this parameter is of particular importance for lovers of the so-called subohm — soaring at a low heater resistance (up to 1 ohm), which allows you to achieve high steam saturation (when the resistance decreases, the power increases). Not all batteries are capable of working with sub-ohm heaters, so the suitability of a battery mod for such vaping needs to be clarified.

The highest resistance of the electronic cigarette heating coil.

The meaning of this parameter will be different, depending on which part of the device is in question (see "Type"). For an atomizer, this can be either the resistance of the complete heater, or, if there are several “heads” in the kit, the resistance of the highest-resistance replaceable coil. For a battery mod, the highest resistance is indicated at which the battery is able to deliver sufficient power for operation. For the starter set, the data is usually given according to the battery mode, while the resistance of the complete heater (heaters) may be lower than the maximum.

Data on the maximum and minimum (see above) resistance is necessary, first of all, to select an atomizer and a battery mod that are compatible with each other. The atomizer must fall within the operating range of the battery mod, otherwise the battery will either be overloaded (if the evaporator resistance is too low), or simply will not provide the desired degree of heating (if it is too high).

The battery capacity of an e-cigarette or separately sold battery mod. This parameter is indicated only for models with non-removable batteries (see "Battery type"): replaceable cells can be produced in different capacities.

The larger the battery, the longer you can use the device without recharging the battery. However the actual power consumption and, accordingly, the battery life of different models will be different, therefore, only devices with similar operating voltages and atomizer resistances can be compared in terms of capacity.

In general, if battery life is important to you, it is quite possible to proceed from the principle “the more capacious the battery, the better”; and to save money, you can choose a relatively weak battery. It is also worth mentioning that there are schemes for calculating the optimal battery capacity depending on the power, atomizer resistance, etc.; these schemes can be found in special sources.

The maximum power supplied by the battery.

This is one of the main parameters of the battery pack that determines its compatibility with the atomizer. Starter kits (see "Type"), by definition, include atomizers that are optimally suited to a given battery in terms of power, and this parameter is mainly of reference value. But when choosing components separately, you should pay special attention to it. Higher power allows you to achieve more saturated steam, but only up to certain limits — too much heating leads to a deterioration in taste, and even burning of the wick (which, all the more, does not contribute to improving the sensation of soaring). So the atomizer must normally transfer the power of the battery, otherwise, at best, you will have to constantly limit the power with the help of a varivolt or variwatt (see "Battery mod"), and at worst, normal use will be impossible at all.

Note that for classic evaporator tanks with one spiral, power up to 40 W is considered sufficient; more powerful batteries are designed mainly for advanced serviced models, drip atomizers and bacodrips(see "Type of atomizer") that have more than one coil and, accordingly, are more high consumption in terms of energy consumption. Also note that the actual heating power depends on the voltage, and in fact it may be lower than the claimed one, depending on the resistance of the atomizer. See “Maximum voltage".