Comparison F&D A-530U vs Microlab M-800

The range of audio frequencies supported by acoustics. The wider this range — the fuller the reproduced sound, the lower the likelihood that some of these details at low or high frequencies will remain “behind the scenes”. At the same time, the human ear is able to hear frequencies of the order of 16 – 22,000 Hz, and with age, this range narrows even more. In modern audio equipment, especially at the top level, there may be more extensive ranges, but from a practical point of view, this does not make much sense. In addition, it is worth noting that a wide frequency range in itself does not guarantee high-quality sound — a lot also depends on the frequency response.

The electrical resistance of the speakers to alternating current. This parameter is important primarily for normal compatibility with the amplifier: too low speaker impedance can lead to distortion, overload, and even damage to the speakers, and too high impedance can reduce the sound volume. At the same time, the vast majority of modern computer acoustics have their own amplifiers and are connected via a line input. Therefore, the impedance data is more of a reference value; in fact, this indicator may be needed only when connecting speakers to a “non-native” power amplifier, bypassing the standard one.

Total speaker power rating — the sum of the power ratings of all components (front, rear, centre, etc.)

Rated usually means the highest average sound power that the speakers can produce without overloading and damage. Individual peaks of sound can significantly exceed this figure, but it is the average value that is key — in particular, it is it that determines the overall loudness of the acoustics. However it should be borne in mind here that in sets with a subwoofer, the latter can account for about half of the total power of the entire system, while the actual volume is determined mainly by the main speakers. In fact, this means that with equal total power, acoustics with a subwoofer can sound noticeably quieter than a model without a subwoofer: for example, a 2.0 system at 20 W will have 10 W per main channel, while in a 2.1 model at 20 W with 10- watt subwoofer on the main speakers will have only 5 watts.

As for specific values, in the quietest modern PC speakers, the power does not exceed 10 watts. An indicator of 10 – 25 W can be called relatively modest, 25 – 50 W — average, and values of 50 – 100 W and above are found mainly in sets with subwoofers, where a significant part of the power falls on the bass speaker (although there are also ordinary stereo speakers with similar features)....

Theoretically, the power of acoustics also affects its compatibility with a specific amplifier: speakers should not be inferior to it in terms of rated power, otherwise sound distortion and even equipment damage are possible. However, computer acoustics in the vast majority of cases are used with their own amplifiers, optimally matched to the speakers installed in the speakers. So this moment becomes relevant only in some very specific cases — for example, when replacing a complete external amplifier (see below) with another one.

The power rating of each individual front speaker provided in the speaker system. This parameter can be specified for a system with any number of speakers (see above) — all sound formats used in computer acoustics provide a pair of front speakers.

In the most general terms, the higher the power, the louder the speaker is capable of sounding. For more information about this parameter, see "Total power" above. Also note here that for stereo systems without a subwoofer, the power of one front channel is half of the total power; in more advanced acoustics, the power ratio between the channels may be different.

Rated power of the complete subwoofer of the acoustic system.

Recall that a subwoofer is a specialized speaker for low and ultra-low frequencies; such a speaker is especially useful for games and movies, it is for such content that well-defined bass is most important. Accordingly, the saturation and (to a certain extent) the overall sound quality of low frequencies depends on the power of such a speaker. "Subs" are usually matched to the power of the rest of the system components, however, sets with a similar total power of the main channels may still differ in the characteristics of the subwoofers.

It is also worth noting that the power of this component can be a very significant part of the total power of all acoustics: in some models, about half of the “total watts” (or even more) falls on the subwoofer. This should be taken into account when comparing; see "Total power" for more details.

A phase inverter is a tube of a special design that connects the inner volume of the speaker housing with the outer space. Due to the precisely selected length, such a tube improves the sound of low frequencies, making it more saturated and uniform. The main disadvantage of a phase inverter is that a hum may occur due to the movement of air in the tube; however, manufacturers design speakers in such a way as to minimize the likelihood of this phenomenon.

Note that the presence of a phase inverter is especially useful for subwoofers, but this feature can also be found in general-purpose stereo speakers — for the same reasons.

— Bluetooth. A technology used to wirelessly connect various devices. Allows you to transmit an audio signal, for this purpose it is most often used in computer speakers. This feature is especially convenient when using speakers with equipment that has its own Bluetooth modules — primarily with laptops and monoblocks; it is also possible to connect to compact gadgets like a smartphone or tablet (although it is usually more convenient to use specialized self-powered speakers with such devices). And for computers that do not have Bluetooth, separately connected adapters are available. The range of such a connection is at least several metres; the convenience of the lack of extra wires is obvious. However note that a regular Bluetooth connection compresses the sound quite strongly and may degrade its quality. Therefore, if this moment is critical for you, you should choose speakers with support for one of the aptX options or with a higher Bluetooth version. Each next "generation" has additional features.

— Support for aptX. A feature found in Bluetooth speakers (see above). The aptX codec is used to improve the quality of audio transmitted over such a connection; according to the creators, it allows you to achieve quality comparable to Audio CD (16-bit/44.1kHz). Thus, if a regular Bluetooth connection can significantly degrade the sound of even MP3 files with a decent bitrate (not to mention lossless...formats), then when using this codec, the sound quality is often limited not by the properties of the channel, but by the properties of the source file and the acoustics itself . Of course, for aptX to work, it must be supported not only by the speakers, but also by the signal source.

— Support for aptX HD. Support for the aptX HD codec, an updated version of the original aptX (see above). This standard achieves sound clarity comparable to Hi-Res (24-bit/48kHz) audio. On the other hand, its support is more expensive; and the differences from the original aptX only become noticeable on very high-quality audio materials, for which computer speakers are rarely used. Therefore, this function has not received much distribution.

— NFC. Technically, NFC is a universal wireless technology with a range of up to 10 cm, which allows to achieve a very wide range of applications. However, in computer speakers, this technology is mainly used to speed up Bluetooth connection (see above): it is enough to bring another NFC device (for example, a smartphone) to the speaker chip — and the chips will “recognize” each other and automatically set up the connection, the user will only have to confirm his.

— USB A. USB port, which allows you to connect external peripheral devices to the speakers — primarily drives like "flash drives". Most often, such a connection is used to play music from external drives — in other words, the presence of USB A turns the speakers into a standalone music centre. Often, it is also possible to charge portable gadgets (for example, smartphones) from this port. On the other hand, note that speakers with this feature are noticeably more expensive than similar models without USB, and they may be inferior in sound quality due to the presence of additional electronics that can interfere.

— Card Reader. Own device for reading memory cards, most often the SD standard. Speakers with a card reader can work like a stand-alone music centre: music from a memory card can be played even without a computer. At the same time, the card reader itself is used only by speakers; the ability to read a memory card by a computer is usually not provided in such models. It is also worth bearing in mind that the memory card slot and the electronics that “serve” it are a potential source of interference, so speakers with this function may be inferior in sound quality to counterparts without a card reader (at a higher cost).

— FM receiver. The presence of a built-in FM tuner allows you to use the speaker system as a radio receiver — to receive and play FM radio broadcasts. It should be noted that for reliable reception, most likely, an external antenna will be required; a cable for connecting it is sometimes included, but the antenna itself must be purchased separately.

— Treble adjustment. The ability to separately change the volume of high frequencies. In fact, it is the most simplified version of the equalizer: it allows you to adjust the overall colour of the sound by changing the HF level relative to the rest of the frequency spectrum. Most often used in combination with bass control (see below), but can also be provided as the only frequency control.

— Bass adjustment. The ability to separately change the volume of high frequencies. Similar to the treble control described above, used to adjust the overall tone of the sound. At the same time, quite a few models with this function have only a LF control (without a HF control). But do not confuse this function with subwoofer level control. In this case, it is precisely the adjustment of the lower frequencies of the entire system that is implied.

The presence of detachable cables will save you from possible damage to the device associated with bending the wires. If such an incident occurs, an easy replacement of the wire with a new one allows you to continue using the speakers, and not carry them to a service centre. However, this solution is mainly used in higher-level models, which affects the cost. At the same time, not only audio cables can be removable, for which connectors are provided (according to the classics, this is RCA), but also the power cable.

The type of remote control that the speakers are equipped with — of course, if such a remote control is provided at all.

— Wired. The remote control is a separate device connected to the control component of the system (“main” speaker, subwoofer, external amplifier) using a separate wire. Such a remote control is not as mobile as a wireless one, and the wire itself can create some inconvenience. On the other hand, these shortcomings are not always really noticeable: computer speakers are most often located in close proximity to the listener, and he does not have a need for "long-range" control. At the same time, wired remotes are reliable, inexpensive, do not require batteries and work even without being in direct line of sight of the speakers (unlike wireless ones, which often use IR control). However note that only the most basic functions are usually carried out on such a remote control — such as adjusting the volume and tone.

— Wireless. Wireless remotes most often operate via an infrared channel — similar to remotes for TVs, air conditioners, etc. The main advantages of such control are freedom of movement within at least a few metres from the acoustics. In addition, wireless remotes are often given control over advanced settings. At the same time, there should be no obstacles between the remote control and the receiver (one of the speakers, subwo...ofer, etc.); and such accessories cost much more than wired remotes.

— Wired and wireless. Acoustic kits equipped with two remote controls at once — wired and wireless. The features of both options are described in detail above, and their combination allows you to choose the remote control depending on what is required at the moment — to have control at hand while sitting at the computer, or to adjust the sound from a distance of several metres, moving around the room. In addition, wired and wireless remotes may differ in terms of functionality. However, it is worth considering that such equipment significantly affects the cost.