Comparison LG PF1000 vs LG PF1500

The brightness of the image produced by the projector at maximum backlight brightness. Usually, the average brightness of the screen, derived from a special formula, is indicated. The higher it is, the less the image depends on ambient light: a bright projector can provide a clearly visible image even in daylight, but a dim one will require dimming. On the other hand, increasing brightness reduces contrast and accuracy of colour reproduction.

Accordingly, when choosing this parameter, you need to consider the conditions in which you plan to use the projector. So, for office or school/university use, a brightness of at least 3000 lm is desirable — this allows you to get normal visibility without obscuring the room. In turn, among the top models a very low brightness can be found, because. such projectors are usually installed in rooms specially designed for them with good darkness level. And in ultra-compact devices it is impossible to achieve high brightness for technical reasons.

Detailed recommendations on the optimal brightness for certain conditions can be found in special sources. Here we note that anyway, it is worth choosing according to this indicator with some margin. As mentioned above, as brightness increases, contrast and colour quality decrease, and you may need to use the projector at a reduced brightness to achieve the desired picture quality.

The closest distance to the screen that the projector can be used on. Typically, this is the minimum distance at which the image from the projector remains in focus.

This parameter is especially important if the device is to be placed at a small distance from the screen (for example, in a cramped room). Some modern projectors are able to work normally at a distance of 10 – 20 cm. Also note that the throw distances are determined primarily by the lens, and if the initial range of these distances does not suit you, perhaps the situation can be solved by replacing the optics.

The farthest distance from the screen that the projector can be used on. This is the maximum distance at which the image remains in focus and maintains acceptable brightness — at least enough for viewing in a darkened room on a high-quality screen.

It is necessary to choose according to this parameter taking into account the expected operating conditions and the distances to be dealt with. At the same time, it's ok to have a certain margin for the maximum distance — since, as already mentioned, it is usually indicated for an perfect screen and a darkened room, and such conditions are not always available. Also note that although the throw distances depend on the lens, not every projector with an interchangeable lens allows the installation of more "long-range" optics than the standard one — the device may simply not have enough brightness for an increased distance.

Size of the image projected by the projector. Usually, it is indicated as a range — from the smallest, at the minimum throw distance, to the largest, at the maximum. About throw distances, see above; here it is worth saying that the choice of diagonal size depends both on the distance between the screen and the audience, and on the format of the projector. For example, to watch a video, the best option is the situation when the distance from the viewer to the image corresponds to 3-4 diagonals, and a relatively large picture can be useful for working with presentations. More detailed recommendations for different situations can be found in special sources; here we only recall that the image must fit on the screen used with the projector.

The magnification range of optical zoom that the projector can provide.

Optical magnification of the image is carried out due to the operation of the lenses in the projector lens. With such an magnification, the size of the entire image changes; this can be useful both for adjusting the “picture” to the screen size, and for detailed viewing of individual details (the main thing is that these details do not crawl out of the screen when enlarged). In general, optical zoom is considered more advanced than digital one, because it allows user to adjust the diagonal without moving the projector, and maintains the original resolution of the "picture" regardless of the magnification. However lenses with such an possibility ("zoom lenses") are more complicated and more expensive than fixed optics, but the difference in price is almost imperceptible compared to the cost of the projectors themselves.

— Light sensor. A sensor that detects the level of ambient light. Most commonly used to automatically adjust the brightness of the projector to suit current conditions. So, in a darkened room, high brightness is not needed, but in daylight, on the contrary, you cannot do without it. You can also adjust the operating mode manually, but it is more convenient when the projector does it automatically.

— DLNA support. DLNA technology is designed to connect home electronics into a single network and exchange content in real time. One of its advantages is that DLNA devices are guaranteed to be compatible with each other regardless of model and manufacturer. In a projector, this feature can be used, for example, to view a movie on a large screen from a computer hard drive, or to display an Internet broadcast on this screen that was originally opened on a tablet. DLNA works on the basis of a standard local network, with a connection via LAN (see "Management ports") or Wi-Fi (see below).

— MHL support. The projector has HDMI inputs that support the MHL standard. This standard is used to transfer video and audio from mobile gadgets (via microUSB) to external devices. Accordingly, this feature is useful for those who plan to connect smartphones and other portable equipment to the projector. At the same time, an MHL gadget connected t...o a compatible HDMI port can also be charged in the process. Note that you can also output the MHL signal to a regular HDMI port, but this will require an adapter, and the charging function will not be available.

— Picture-in-picture. Ability to play two channels simultaneously on one screen: main and additional (in a separate small window). The sound is played only for the main channel. This mode allows, for example, to skip a break in a football match and not be late for the second half. Note that for this function to work, images must come from different sources — for example, from two different tuners, or from a tuner and an external device (DVD player, media centre, etc.).

— PJ-Link protocol. The projector supports the PJ-Link protocol. This is a service standard designed to control projectors over local networks (usually LAN or HDBaseT, see "Management port"). All PJ-Link-enabled equipment (projectors, controllers) is fully interoperable regardless of brand and manufacturer, making it much easier to build networks of multiple projectors and replace individual components in such networks.

— 3D support. Support for 3D implies the ability to reproduce three-dimensional stereoscopic images. A 3D image can be based on various technologies. Traditionally, active (see the relevant paragraph), passive (see the relevant paragraph) and hybrid 3D technologies are distinguished. Special glasses are required to view the three-dimensional image. In the case of active 3D, special shutters are built into the glasses, which operate from an independent power source. For passive and hybrid 3D, regular 3D glasses without battery power are sufficient.

— Active 3D. Active 3D technology is based on the principle of alternating flickering of the image. The flickering of the image on the screen is synchronized with the flickering of the lenses in the glasses, as a result, each eye receives a separate image, which makes the picture three-dimensional. The main advantage of active 3D is the ability to view images without reducing the original picture quality. You can look at the screen from any angle and from any position, while the image will still be three-dimensional. Among the shortcomings, there is the presence of some discomfort for the eyes, which occurs due to the regular flickering of lenses in glasses. Also, active 3D glasses may darken the original brightness of the image somewhat. Additionally, glasses of this type are very expensive.

— Passive 3D. Passive 3D provides the display of a double image. Passive 3D glasses use special lenses that cut off the duplicate image in such a way that each eye sees only the image intended for it, which creates the illusion of a three-dimensional image. The main advantage of passive 3D is that it does not tyre the eyes, which is typical for active flickering 3D. Passive 3D glasses are inexpensive.

— Interactive pen. The projector supports interactive pen technology. This technology allows you to actually turn the projected image into an interactive whiteboard: with a pen, you can draw, write and make notes directly on the projected image, which is especially useful during presentations and educational events. It is worth taking into account that the pens themselves and additional equipment for their work may not be included in the set.

— Multimedia (air mouse remote). Air mouse remote are devices that have a gyroscope, which allows you not only to switch menu items with the “↑”, “↓” buttons, but to use the remote control as a mouse. By directing it to the screen, a cursor will appear that moves in the direction of the remote control. This makes management easier and faster.

— Voice control. The projector's support for voice control allows you to dictate certain commands through the remote control. However, voice control does not cover all functions and recognition accuracy may require re-entering the command. If you need a more extensive range of functions, then pay attention to the voice assistant.

— Voice assistant. For a long time now, device control has been shifting to voice commands. For this, certain interfaces and systems are used. The most popular are Amazon Alexa and Google Assistant. For "apple" devices, this is Apple Siri, but this technique is not presented in projectors. At the same time, unlike the voice control function, the voice assistant does not just turn on this or that function, mode, makes it louder, quieter, but allows you to perform certain operations in applications, whether it is to launch the desired clip on Youtube or display the weather in the browser.

Inputs for connecting external video sources provided in the projector.

— VGA. Analogue video interface, that considered obsolete, but still quite popular; VGA outputs are found in video technology, as well as in some computer graphics cards. It supports resolutions up to 1280x1024, which allows you to work with 720p video, but more advanced HD standards are out of the question. Audio signal transmission via VGA is not provided, the soundtrack for such a video will have to be connected separately.

— DVI. A video interface primarily used to connect projectors to computers. Initially, it did not provide sound transmission, but this possibility is gradually being introduced. Nowadays, several varieties of DVI are used. So, according to the signal format, purely digital DVI-D and combined DVI-I, which supports digital and analogue video, are distinguished. In both of these varieties, a two-channel digital data transmission format can be used, in which the maximum video resolution reaches 2560x1600 (in single-channel it is 1920x1200). Connectors and plugs DVI-D and DVI-I are compatible with each other if the number of channels matches, or if a single-channel video signal is connected to a two-channel input.

— DisplayPort. A digital interface originally designed for connecting LCD monitors. Modern versions are similar in capabilities to HDMI, they support HD resolutions of 1080p an...d higher, as well as multi-channel audio transmission. However, such outputs are rare in video devices; the main area of application for DisplayPort has been and remains computer technology. In particular, it is this connector (as well as its reduced version miniDisplayPort) that Apple regularly uses in its computers.

• — DisplayPort v 1.2. DisplayPort v 1.2 has a bandwidth of 17.28 Gbps. This signal transmission standard has full support for FullHD video format. QuadHD and 4K formats are partially supported.
• Display Port v 1.3. The maximum bandwidth of DisplayPort v 1.3 is 25.92 Gbps. This version of DisplayPort provides full support for FullHD and QuadHD formats. 4K and 8K video modes are partially supported.
• Display Port v 1.4. The bandwidth limit of DisplayPort v 1.4 is 32.4 Gbps. This version of DisplayPort features enhanced support for 4K video, including 144Hz refresh rates, while DisplayPort 1.3 only limits 4K to 120Hz. Like the previous version, DisplayPort 1.4 partially supports 8K video modes.

— BNC. Bayonet type connector used to connect coaxial cable. Projectors use this connection to transmit analogue component video (see the relevant paragraph) or uncompressed SDI video. BNC refers to professional interfaces and is found in projectors of the corresponding class.

— S-Video. Analogue interface for video transmission (without work with audio). Provides two channels for transmitting image information, similar to the component input described below. However, on the one hand, S-Video uses only one connector instead of three, on the other hand, the bandwidth of this interface is noticeably lower, it is not suitable for HD resolutions, in light of which it is considered obsolete and is rare, mainly found in specialized video equipment.

— Composite. Initially, a composite interface is called an analogue interface for transmitting video and sound, using 3 separate channels (for the video signal and the left and right audio channels). However, in this case, most often only one connector is meant — for video; audio inputs on projectors are listed separately and are referred to as RCA (audio) (see "Audio connectors"). In general, the composite interface does not have a high picture quality, besides it is not suitable for transmitting an HD image and is considered obsolete. On the other hand, it is very common and is found not only in modern video equipment, but also in outdated ones; for example, you can connect a VHS-VCR to the projector through this interface.

— Component. An interface that is considered the most advanced among modern analogue video standards. The video signal with this connection is divided into three components transmitted over separate cables; this provides good interference resistance and sufficient bandwidth even for HD resolutions. But the sound in this interface is not supported.

— RCA (audio). Analogue audio interface using RCA jacks. Depending on the model of the projector, it can serve as both an input (for example, in addition to the component video input) and an output for connecting external audio devices. We only note that in this case only one channel of sound is transmitted through one RCA connector, and a pair of “tulips” (for the left and right channel) is considered an input or output.

— 3.5 mm input (mini-Jack). This connector is more compact than RCA, in addition, it allows to work with two stereo channels through one jack. On the other hand, a 3.5 mm connection is less reliable and more prone to interference. Therefore, such an input is designed mainly for simple tasks — such as transmitting sound from the audio output of a PC or laptop.

— 3.5 mm output (mini-Jack). This in any case is an analogue output, however, its specific purpose may be different. So, in some projectors it plays the role of a linear interface and is used to output an audio signal to active sound system or an external amplifier. In other devices, the mini-Jack works as a headphone output. There are models where these functions are combined in one connector.

— Optical output. An output for transmission of a digital audio signal by a fibre optic cable; allows the transmission of multi-channel audio. Not...able for its complete insensitivity to electromagnetic interference. On the other hand, fibre optic cable is quite fragile, it must be protected from bending and strong pressure.

— Microphone input. Input for connecting an external microphone to the projector. Using it, you can stream sound from a microphone using the projector's own amplifier — for example, comment on a presentation through the same speakers through which the main sound goes.

The power consumed by the projector during normal operation. Both the high consumption of the device and the requirements for power supply providing depend on this indicator: for example, heavy professional projectors of 3500 W and above cannot be plugged into standard sockets, they require a special connection format.

Keep in mind that when using traditional mercury or gas discharge lamps, high brightness inevitably requires high power. Energy efficient LED projectors do not have this disadvantage, but they are still relatively uncommon, and LED is not always a suitable type of lamp.