Comparison Bosch WTW 85540 vs Whirlpool DDLX 80114

— Condensing (recuperative) The general principle of condensation drying is as follows: heated air is passed through the laundry drum, captures moisture, and then enters the refrigerator, cools down, and excess moisture condenses in a special tank. The advantage of all condensing machines over air vented ones is that they are easy to install. They do not need to be connected to ventilation and can be installed in any room. On the other hand, the user needs to monitor the condensate tank and periodically drain the accumulated water. And such units are somewhat more complicated and more expensive than ventilated ones. However, recuperative dryers are the simplest and most inexpensive among condensing dryers. By the name, the role of a refrigerator in them is played by a recuperator: a heat exchanger that dumps excess heat into the outside air. The heating of the air inside is usually carried out using a heating element. Due to their availability, such machines are very popular, but they have serious drawbacks. Firstly, devices of this type have high electricity consumption. Secondly, the efficiency of their work is relatively low. Moreover, it directly depends on the temperature difference between the air outside and inside the dryer.

— Condensing (heat pump drying). The most advanced and most expensive type of condensing dryer. See above for more information on conde...nsing drying in general. Note that in models of this type, the refrigerator operates due to a heat pump — a compressor that takes excess heat from the condensation chamber and transfers it to the heater. It provides several advantages over traditional recuperative drying. One of the most noticeable is high efficiency and economy: the heat pump allows you to reuse the accumulated thermal energy, and less electricity is spent on its operation than on the constant air heating in recuperative models. In addition, drying is easier and faster, and the work speed is practically independent of outdoor conditions. And such a machine almost does not produce excess heat. The disadvantages of models with a heat pump are traditional — complexity and high cost.

— Air vented. A kind of drying in which excess moisture is blown out of the machine into the outdoor space. Compared to condensing drying, this option allows you to create simpler, cheaper and more compact units. And such models are somewhat easier to use because they do not require monitoring the water level in the condensate tank. On the other hand, installing a ventilated machine is noticeably more difficult. So, in the room where the unit is located, there must be a powerful ventilation system, otherwise, there will always be high humidity and temperature. Such a microclimate is not only harmful to people and furniture but also significantly worsens drying efficiency. If it is impossible to organize general ventilation for the room for one reason or another, one will have to make a separate air duct to remove steam from the dryer. As a result, this type of drying is considered inconvenient and extremely rare.

The maximum amount of laundry that can be loaded into the dryer; in other words, the largest weight of laundry that the machine can efficiently process in one cycle.

Capacity is usually indicated by the weight of the dry laundry. Thanks to this, when preparing the laundry for washing, you can immediately assess whether it will fit in the dryer at a time or, on the contrary, you can get by with a small drying. However, even the most modest modern dryers (and even slim ones up to 50 cm) in most cases hold 7 kg — this is comparable to loading the drum of a medium-capacity washing machine. And in the most capacious models, this figure can reach 10 – 11 kg. It is quite enough for domestic and even professional use (for example, in laundromats or laundries of hotels, etc.). However, the typical figures are drying for 8 kg and models for 9 kg of laundry. Bigger capacity is relevant for industrial equipment and is not found in consumer-level models.

Also, when choosing, note that in the specs the maximum capacity is usually indicated for linen made of cotton fabric. For other, more voluminous materials, the capacity can be noticeably less — for example, the weight limit for wool products is usually 4-5 times less than for cotton.

The internal volume of the dryer drum.

A larger drum can accommodate more laundry, but there is no rigid dependence here: models with the same volume may differ in maximum load. It is because to process a large mass of laundry, one need not only a capacious drum but also an engine of appropriate power. At the same time, in a larger drum, the same mass of laundry will dry more efficiently than in a small one, because laundry will be more freely distributed over the drum, crumpled less, and warm air will better penetrate the folds of the fabric. As a result, for the same drum volume, a model with a smaller load will be more efficient and performant than a model with a larger load. On the other hand, a volumetric drum takes up more space and the dimensions of the dryer are largely determined by the dimensions of the drum.

The number of preset drying programmes. Such programmes are often optimized for a specific type of fabric: linen, silk, synthetics, etc. The more drying programmes, the more versatile and easier the dryer is to use. However, a specific set of modes in different models may be different, and even a large variety of programmes does not guarantee that one of them will be suitable. So before buying, it is advisable to specify not only the quantity but the list of claimed programmes.

The presence of a drying programme with steam in the dryer.

In this mode, the laundry in the drum is treated with hot steam. Note that this procedure is not suitable for drying as such; its purpose is rather to refresh and moisturize the fabric. For example, steam drying can be used as an alternative to washing when clean unwashed clothing has absorbed an unpleasant odour. It can be used to moisten overdried laundry for subsequent ironing.

Lighting system for the internal volume of the device. It usually turns on automatically when the dryer door is opened - thus reducing the likelihood that some items (especially small and dark ones) will be forgotten in the drum.

System for automatic cleaning of the heat exchanger from fibres and all kinds of deposits that prevent easy air circulation. The self-cleaning function is performed during each drying cycle. It extends the life span of the heat exchanger and ensures consistently low energy consumption over the life span of the dryer.

This option allows you to automate the process of draining the condensate collection tank (respectively, it is relevant only for dryers with a condensation principle of operation). At the end of the drying process, the condensate accumulated in the tank is automatically drained into the sewer. To do this, a pump and a hose are provided in a dryer with a drain into the sewer. The function of draining into the sewer allows you to significantly simplify the operation of the dryer, while in models without this option, the user must drain the condensate tank manually. Of course, manual emptying does not require much effort because the average condensate collection tank has a volume of about 5 litres, but still not very convenient.

It is an indicator signalling the filling of the tank with condensate and the need to empty it. It is used exclusively in models with a condensing type of drying (see above). The specific device and functionality of the indicator may be different: in some models, it only warns of a critical liquid level. In others, it can display the exact amount of condensate collected. However, this feature greatly simplifies the monitoring of the operation of the dryer and reduces the risk of flood and other troubles that can lead to an overflow of the tank.