Width
Tire section width is the distance between the sidewalls of an inflated but not loaded tire. As a rule, this parameter is indicated in millimeters, but there are also inch designations for the profile width.
Width is one of the characteristics that determines the compatibility of a tire with a specific wheel (the second characteristic is the mounting size). It is worth noting that the width of the tire does not have to strictly correspond to the width of the rim; certain deviations are allowed. There are special tables that allow you to determine the permissible width values for a particular wheel; in addition, such recommendations may be indicated in the documentation for a specific car.
The following tire width options are available on the modern market:
135 mm,
145 mm,
155 mm,
165 mm,
175 mm,
185 mm,
195 mm,
205 mm,
215 mm(in inches this is
8.5”),
225 mm,
235 mm,
240 mm(in inches this is
9.5”),
245 mm,
255 mm,
265 mm(in inches this is
10.5”),
275 mm,
285 mm,
290 mm(in inches this is
11.5”),
295 mm,
305 mm,
315 mm,
320 mm(in inches this is
12.5”),
325 mm,
335 mm,
345 mm(in inches this is
13.5”) and
over 345 mm(
over 13.5”).
Aspect ratio
Tyre aspect ratio. This parameter is usually expressed as a percentage of the width, since it is not the height itself that is of practical importance, but its ratio with the nominal section width.
In general, the lower the ratio, the more stable the tyre, the better it is suitable for high-speed driving on flat roads. Higher ratio, in turn, work better on rough surfaces and over obstacles, making them good for bad roads and
off-road. If we talk about specific numbers, nowadays, the following options are spread on the market:
— Low profile tyres:
25%,
30%,
35%,
40% ;
— Medium profile :
45%,
50%,
55%,
60% ;
— High profile :
65%,
70%,
75%,
80%,
82%,
85%, and
90% or more.
Tyre inner diameter
Tyre inner diameter in inches. The key parameter that determines the possibility of installing a tyre on a car: the tyre diameter must match the diameter of the rim. It is worth noting that some vehicles have +/- 1 inch diameter tolerance; this point should be clarified separately in each case.
In modern passenger vehicle tyres, the following rim diameters are most widely used:
12",
13",
14",
15",
16",
17",
18",
19",
20",
21",
22",
23",
24".
Load index
The maximum weight load that the tyre is able to carry. It is denoted by a conditional figure, each of which corresponds to a certain value:
66 - 300 kg, 67 - 307 kg, 68 - 315 kg, 69 - 325 kg, 70 - 335 kg, 71 - 345 kg, 72 - 355 kg, 73 - 365 kg, 74 - 375 kg, 75 - 387 kg, 76 - 400 kg, 77 - 412 kg, 78 - 425 kg, 79 - 437 kg, 80 - 450 kg, 81 - 462 kg, 82 - 475 kg, 83 - 487 kg, 84 - 500 kg, 85 - 515 kg, 86 - 530 kg, 87 - 545 kg, 88 - 560 kg, 89 - 580 kg, 90 - 600 kg, 91 - 615 kg, 92 - 630 kg, 93 - 650 kg, 94 - 670 kg, 95 - 690 kg, 96 - 710 kg, 97 - 730 kg, 98 - 750 kg, 99 - 775 kg, 100 - 800 kg, 101 - 825 kg, 102 - 850 kg, 103 - 875 kg, 104 - 900 kg, 105 - 925 kg, 106 - 950 kg, 107 - 975 kg, 108 - 1000 kg, 109 - 1030 kg, 110 - 1060 kg, 111 - 1090 kg, 112 - 1120 kg, 113 - 1150 kg, 114 - 1180 kg, 115 - 1215 kg, 116 - 1250 kg, 117 - 1285 kg, 118 - 1320 kg, 119 - 1360 kg, 120 - 1400 kg, 121 - 1450 kg, 122 - 1500 kg, 123 - 1550 kg, 124 - 1600 kg, 125 - 1650 kg, 126 - 1700 kg, 127 - 1750 kg, 128 - 1800 kg, 129 - 1850 kg, 130 - 1900 kg, 131 - 1950 kg, 133 - 2060 kg.
While choosing according to this indicator, it is worth considering not only the maximum weight of the car for which tyres are going to buy, but also the distribution of weight along the axles. With passenger cars, everything is simple — the weight is distributed approximately equally, so to determine the load on each wheel, it is enough to divide the maximum mass of the car by 4 (the number of wheels). H...owever, in minibuses, light trucks and SUVs, the situation is different: the weight distribution can be unequal, so you should refer to the manufacturer's documents or other special sources to calculate the load on each wheel.
Anyway, the load index must not be exceeded — this creates the danger of an accident. In fact, the wheel load should be at least 10 – 15% below the maximum, this will give an additional guarantee in case of abnormal loads. Also note that in some high-speed tyres, with the speed maximum approaching, the permissible load decreases: for example, for tyres with the V index (see "Speed rating") with speed over 210 km/h, it is recommended to reduce the load by 3% for every next 10 km/h increase in speed, similar recommendations apply to models with indexes W and Y. These details are usually described in the manufacturer's documentation and other special sources.
Fuel efficiency
The rolling resistance rating that the tyre corresponds to. The higher this figure, the lower the resistance, the less fuel is spent to overcome it and the more economical the tyre is. Efficiency indices are denoted by letters of the Latin alphabet in descending order of efficiency:
A(highest efficiency),
B,
C,
D,
E,
F,
G(lowest efficiency).
With other things being equal, more economical tyres tend to cost more, but the difference is offset by fuel economy.
Wet Grip
An index that determines the overall performance of a tyre on wet pavement. Lettered from
A(highest) to
G(lowest); intermediate options, respectively —
B,
C,
D,
E and
F.
The higher this indicator, the stronger the tyre grips to the wet road, the more efficient and safer it will be in difficult weather conditions. At the same time, it is worth noting that a low grip index does not mean unsuitability for driving in rain or snow — you just need to be more careful using such tyres. Conversely, a high index does not relieve the driver of the need to be careful in difficult weather conditions.
Noise Level
The average noise level created by a tyre while driving. The lower this indicator, the more comfortable this model will be, the less additional noise it will create.
Note that EU rules provide 3 categories of tyres in terms of noise.
“Quiet” are considered models with an index of up to 68 dB,
“medium” — 68 – 71 dB,
“loud” — 72 dB and above.
Wear resistance (Treadwear)
Tyre wear resistance rate according to the Treadwear standard issued by the US National Highway Traffic Safety Administration.
This rate indicates how far the tyre is able to travel until the tread reaches a critical level of wear. Treadwear is indicated in conditional points; formally, every 100 points correspond to 48,000 km (30,000 miles). However, it should be noted that testing according to this standard is carried out under perfect conditions — on flat roads, without numerous sharp accelerations and brakings, at a stable temperature, etc. Therefore, real wear resistance, usually, is lower by at least 20 – 30 %; and for a full guarantee, the claimed indicator is generally recommended to be divided by two. For example, formally the value of Treadwear 240 corresponds to a mileage of 48 × 2.4=115.2K km — however, in fact it is hardly worth counting on more than 90K km, and it is best to keep on the value of 55 – 58K km.
Generally, Treadwear ratings up to 250 are considered fairly low, 251 – 300 are considered average, 301 – 350 are above average, and over 350 is typical for
the most durable tyre models. Note that this characteristic is given mainly for summer, less often — all-weather tyres; winter tyres should be quite soft, which makes it difficult to achieve more or less worthy wear resistance rating.
