Comparison Mercury F5M vs HDX T5BMS

The duty cycle of the petrol engine (see "Engine type") installed in the boat.

— Duplex. Two-stroke engines have a good ratio of volume and useful power, besides, they are simpler in design and cheaper than four-stroke ones. On the other hand, they have a rather high fuel consumption and noise level, and gasoline and oil must be filled not separately, but as a mixture. Such a mixture must correspond to certain proportions, otherwise the engine will either wear out and heat up due to a lack of oil, or smoke due to its excess. However high-end motors can use automatic mixing systems (see below), eliminating the need for the user to manually prepare the mixture. However, even when perfectly proportioned, two-stroke engines burn a certain amount of oil along with gasoline, which is why they are considered dirtier than four-stroke engines.

— Four stroke. For the same working volume, four-stroke engines tend to have less power than two-stroke ones. They also require compliance with specific transportation rules. However, this is offset by a number of advantages — primarily relatively low noise levels and gasoline consumption. In addition, gasoline and oil are refueled separately into the engine — this is more convenient and economical than preparing a mixture; and during normal operation, the lubricant practically does not burn out, which also has a positive effect on the environmental frien...dliness of the engine. At the same time, such units are quite expensive, as a result of which the four-stroke cycle is typical mainly for premium outboard motors.

The maximum operating power of the outboard motor, expressed in kilowatts.

The practical value of motor power is described in detail in “Maximum power" is higher. Here we note that the kilowatt (derivative of watt) is just one of the units of power used in fact along with horsepower (hp); 1 HP ≈ 735 W (0.735 kW). Watts are considered the traditional unit for electric motors (see "Engine Type"), but for a number of reasons, outboard motor manufacturers use this designation for gasoline models as well.

The working volume of a gasoline outboard engine (see "Engine type"). This term usually means the total working volume of the cylinders.

The larger this value, the higher the motor power, usually (see the relevant paragraph). At the same time, with an increase in the working volume, fuel consumption, weight and dimensions of the unit also increase; and power depends not only on this indicator, but also on a number of other factors — ranging from the number of strokes (see "Engine duty cycle") or the presence of turbocharging (see below) and ending with specific design features. Therefore, situations are not excluded when a smaller engine will have more power, and vice versa.

The diameter of a single piston in a gasoline (see "Engine type") outboard motor. In most cases, this parameter is purely reference; situations where data on the piston diameter is really needed are extremely rare — usually during the repair or maintenance of the engine.

The working stroke is the distance between the two extreme positions of the piston in a gasoline (see "Engine type") outboard motor. In most cases, this parameter is purely reference; situations where such data is really needed are extremely rare — usually during the repair or maintenance of the engine.

The design of the exhaust system in a gasoline outboard motor (see “Engine type”), more precisely, the method of exhaust gases used in this system.

— Above the screw. This category includes two types of engines. The simplest option is when exhaust gases are emitted directly into the air. Such systems are extremely simple and cheap, but the exhaust can create a noticeable inconvenience for people in the boat (not only because of the gases, but also because of the rather high noise level); therefore, they are found only in the simplest outboard motors, and even then quite rarely. A more common option is to release exhaust gases into the water above the propeller (most often through the so-called anti-cavitation plate — a flat ledge above the propeller). Such systems are more comfortable than "air" ones, while they are simpler and cheaper than propeller exhaust (see below), although they are still considered less technically advanced.

— Through the screw. In systems of this type, the exhaust is led into the water directly through the propeller hub; in fact, the position of the exhaust pipe coincides with the axis of rotation. This reduces the noise level compared to systems using exhaust over the propeller, and also slightly increases power and traction characteristics. The downside of these advantages is the design complexity and, accordingly, the high cost.

The total volume of the fuel tank provided in the design or delivery set of the outboard motor (depending on the type of tank — see "Fuel tank").

The larger the capacity of the fuel tank, the longer the engine will be able to work without refueling, the less often it will be necessary to replenish the fuel supply in the tank. On the other hand, volumetric tanks have appropriate dimensions and weight, especially when filled; the latter is especially critical for motors with built-in tanks (see above).

The type of gasoline recommended for use in an internal combustion engine outboard (see "Engine Type"). In fact, this paragraph indicates gasoline with the lowest octane rating that is allowed to be used in the engine; higher rates are allowed, lower ones are highly undesirable, if not outright prohibited.

The octane number is an indicator that determines the resistance of a particular brand of gasoline to detonation (self-ignition during compression in the cylinder). Detonation is a very undesirable phenomenon, because. it leads to an increase in engine loads simultaneously with a decrease in its power and an increase in the amount of harmful substances in the exhaust gases. And this phenomenon occurs in cases where the engine uses gasoline with lower octane numbers than those for which the unit is designed.

Automobile gasoline, which is also used for refueling boat engines, is marked with the AI or RON index; the first option is used in the characteristics of east european motors, the second — in foreign ones. However, in both indexes, the number after the letters means the octane number. The higher this number, the more demanding the engine is on fuel quality. Thus, for example, a unit under AI-92 will be able to work normally with AI-95, but AI-90 or AI-87 cannot be filled into it. "Record holders" for unpretentiousness today are engines that can work even on the AI-76; but they are a rare exception to the general rule.

The gear ratio describes how fast the propeller of the outboard motor rotates relative to the speed of rotation of its shaft. For example, a gear ratio of 2 means that for each revolution of the shaft, the screw, in turn, makes two revolutions (that is, it rotates twice as fast). In modern outboard motors, this parameter, in fact, is purely reference, because. the practical characteristics of the unit (power, traction, etc.) depend on many design features and are practically not related to the gear ratio.