Comparison KWC KM44D vs Gletcher PM

The working length of the barrel installed in the pistol / revolver is from the chamber to the muzzle. In airsoft models (primarily AEGs, see "Type"), the length of the inner barrel is indicated, along which the bullet directly moves. Three main points directly depend on this parameter: the initial velocity of the bullet, the length of the aiming line and the dimensions of the weapon.

In short-barreled (up to 20 – 25 cm) pneumatics and Flaubert's revolvers, a long barrel allows you to achieve higher initial speeds. However there is no rigid dependence here, and models with the same barrel sizes can differ markedly in initial speed (especially since the latter also depends on a number of parameters, primarily the principle of operation — see "Type"). However, long-barreled pistols are generally better for long-range shooting than short-barreled pistols. This is due to the second nuance — the length of the sighting line: a long barrel allows you to increase the distance between the front sight and the whole, thereby reducing errors in aiming. However, with regard to dimensions, the increase in the length of the barrel not only makes the weapon more cumbersome, but also worsens its balance, since the centre of gravity shifts forward because of this.

There are a couple more nuances associated with this indicator. So, in copies of combat pistols (see above), the barrel length is selected in accordance with the size of the weapon from which this model wa...s copied. And for products chambered for a blank cartridge (see "Type"), this parameter is not indicated at all, since there is virtually no full-fledged barrel in such pistols.

Muzzle velocity — that is, the speed of the bullet at the exit from the barrel — provided by the pistol / revolver. Note that for some weapons, the actual muzzle velocity may vary; for more on this, see "Type", and here we note that for such models, the characteristics usually indicate the average value for perfect conditions.

In general, the greater the speed of the bullet, the more long-range the weapon and the higher its penetrating ability. Thus, in some countries this indicator is the basis for legal restrictions on the sale of pneumatics (usually, bona fide sellers have the relevant information). And for airsoft weapons, this moment is important for safety reasons: too high a ball speed increases the likelihood of injury. However, airsoft guns usually give out less than 100 m / s. By the standards of classical pneumatics, this is very little: most short-barreled pneumatics fall in the range of 100 – 125 m / s, in some models the initial speed can reach 125 – 150 m / s and even more.

In "flobers" speeds are higher: an indicator up to 175 m / s is considered relatively low, up to 200 m / s — average, and some long-barreled models give out more than 200 m / s. However, note that we are talking about the speeds claim...ed by the manufacturer, while the actual performance will greatly depend on the characteristics of the cartridge (load, composition, build quality). Therefore, the actual initial speeds in such weapons may differ markedly from those claimed.

The type of sighting device provided in the design of the pistol / revolver.

The vast majority of short-barreled pneumatics, "floberts" and starting pistols are equipped with the simplest mechanical sights in the form of a front sight and a rear sight. In pneumatic weapons, models with adjustable and non-adjustable sights are approximately equal; in Flaubert's revolvers, the possibility of adjustment is somewhat less common than non-adjustable front and rear sights ; and in models for a blank cartridge, in principle, it makes no sense to provide adjustment. There are pistols / revolvers without sights at all.

Here are the general features of different types of scope:

— Unregulated. Front sight and rear sight, fixed motionless and without any additional settings. The advantages of this design are simplicity, low cost and reliability; in addition, such a sight is almost impossible to shoot down due to an accidental impact of the front sight or rear sight on a foreign object. The main disadvantage is the actual impossibility of adjustment, which does not allow adjusting the sights for a change in distance, side wind or deviations due to production errors. On the other hand, for recreational shooting at short distances, these moments are not decisive, and serious factory defects are extremely rare in fact. So i...f maximum accuracy is not critical for you, a non-adjustable sight may be enough.

— Adjustable. Sights with the ability to adjust; however, the specific possibilities of such adjustment may be different. One of the most popular options is to adjust the rear sight in height, for zeroing weapons at a specific distance. For this, a micrometer screw is usually used. Another option is a rear sight with the ability to move horizontally, it is mainly designed to compensate for errors in the design of the weapon itself, which give a lateral displacement of the point of impact. The most advanced models — mostly high-precision sports pistols — allow you to adjust the rear sight on both axes. Anyway, an adjustable sight is more complicated and more expensive than an unregulated one, it may require additional adjustment by the user himself, but with such devices you can achieve maximum shooting accuracy.
Also note that on the market you can find pneumatics equipped with optical or collimator sights; they are also adjustable.

— Is absent. The absence of their own sights is an extremely rare option, found in two varieties of pneumatic and similar weapons. The first is some spring-piston and PCP pistols (see "Type") with long barrels and high muzzle velocity, designed for high-precision shooting. They have sight mounts (see below) or slots for such mounts, allowing the shooter to choose the sights to their taste. The second variety is revolvers (mainly chambered for Flaubert) of miniature size, originally not designed for aimed shooting in the classical sense of these words.

The overall length of the weapon is usually from the muzzle to the part protruding farthest back (usually the bottom of the handle). This parameter not only allows you to evaluate the overall compactness of the pistol, but can also be useful for selecting accessories for it — for example, a holster, case or carrying bag.