Comparison Prime-X MCM-07 vs Swat VDC-006

The direction in which the camera should face when installed in the standard way. The main purpose of any camera is to provide visibility in "dead zones" that are inaccessible when viewed from the driver's seat directly or using mirrors. However, each type of overview has its own characteristics:

— Reversing camera. Rear-view cameras are an addition to the rear-view mirror, and sometimes completely replace it. Therefore, a prerequisite for this type of model is the ability to work in mirror image mode (see below). Also in our catalog, this category includes universal models that support both direct and mirror modes, and are capable of working both from the rear and from the front.

— Front view camera. A distinctive feature of this variant is the operation in direct image mode (see below).

— Camera for a specific Dashcam. Additional cameras for a specific type of car dashcams (a certain model or family of devices for video recording of what is happening on the roads). Such cameras will come in handy for expanding the horizons of the recorder, which does not provide the presence of auxiliary overview modules, but the technical possibility of their connection is realized.

The technology by which the matrix is made is the photosensitive element of the camera.

— CMOS. Also known as CMOS; both of these entries are abbreviations of the same term, only in different languages (English and Russian). Without going into details, it is worth saying that CMOS matrices are notable for their low cost, compactness, good image processing speed and low power consumption, however, due to the design features, they are prone to the appearance of noise in the image, and therefore somewhat lose CCD in terms of image quality.

— CCD. CCD-type matrices (CCDs) are somewhat more complicated and more expensive than CMOS, but they provide better image quality, including in low light conditions — in particular, due to the low level of noise. This is due both to the low level of heating during operation, and to the uniform light sensitivity of each pixel (whereas in CMOS it can “walk” a little).

— HCCD. A variant of the CCD technology described above, featuring improved sensitivity and even better picture quality in low light.

The physical size of the photosensitive element of a camera. It is usually measured diagonally and is indicated in inches — more precisely, fractional parts of an inch. The larger the sensor, the larger the size of each individual dot (pixel) on it, the more light enters each pixel, and the easier it is to ensure high image quality with a minimum of noise (especially when it comes to shooting at dusk). However you need to remember that only matrices of the same type and resolution can be compared with each other in size. And a large sensor is not always a guarantee of quality — a lot depends on the rest of the hardware of the camera, the quality of its installation and other factors. However, the large size of the sensor usually indicates a high class camera.

The resolution of the frame taken by the camera in video mode, in pixels — in other words, the size of the picture in dots horizontally (first digit) and vertically (second digit). It should be taken into account here that in the case of reversing cameras, the recording in pixels describes only the frame on the camera matrix itself; to describe the "picture" coming to the connected screen, the designation in television lines (TVL) is used. This is due to the fact that the video signal is transmitted in an analogue format; See Video Resolution below for more on all of this. Here we note that with the same resolution in TVL and the same viewing angles, a camera with a higher resolution in pixels will produce a clearer, more detailed image. But HD reversing cameras, and even more so Full HD units.

Although modern electronics are dominated by digital standards, car reversing cameras still use an analogue signal transmission format. This is due to compatibility requirements: such video allows you to use fairly simple screens. And although its quality loses to digital, it is quite enough for most of the tasks facing this class of auto electronics.

An analogue video signal has a size in horizontal and vertical dots. But since the number of vertical dots has a strictly defined number of 625 (in the PAL and NTSC colour system), resolution is usually indicated only by the number of horizontal dots (TV lines).

In fact, this parameter describes the quality of the image that is displayed directly on the screen connected to the camera. There are models with a value of 480, 500, 520, 540, 560 TVL and even higher resolution in TVL. This is important for models with wide viewing angles (see below). On the other hand, in order to use all the features of a camera with numerous TV lines, a screen corresponding to these features is also required; For more details on compatibility with the screen, see specialized sources.

The colour system refers to the format in which colour information is transmitted in an analogue video signal. In modern reversing cameras, the European PAL system or the American NTSC are most often used. It makes no sense to describe them in detail — suffice it to say that for the normal operation of the camera you need a radio tape recorder (or other device with a screen on which the image is displayed) with support for the same colour system. However, incompatibility in this parameter is not fatal — with such a connection, the image will only turn from colour to black and white (in extreme cases, its overall quality will slightly deteriorate).

The lowest ambient light level at which the camera can provide a normal image without additional illumination. In modern models, this indicator varies on average from 0.01 lux (clear night at a quarter moon) to 3 lux (deep twilight).

The lower the minimum illumination, the better the device handles with low light. However, note that in the absolute majority of cases, car cameras at night are used together with car lighting devices: front ones (see "View type") — with main headlights, rear ones — with reversing lights. Therefore, this parameter is rather general reference or even advertising information, rather than a really significant characteristic.

The format for displaying the image on the connected screen. For each type of review (see above), there is a different option that is optimal.

— Direct. The traditional way of displaying an image: the user sees on the screen the same thing that the camera lens "sees" in front of him, with the same arrangement of the details of the situation. Simply put, if some object is located to the left of the centre of the camera's field of view, it will also be visible on the screen on the left side. All front view cameras work this way.

— Mirror. In this mode, an image is displayed on the screen that is “mirrored” horizontally — roughly speaking, one in which “left” and “right” are reversed: an object to the left of the camera lens will be visible on the right side of the screen, and vice versa. All cameras with a rear view type work in a similar way. This is due to the fact that in an ordinary rear-view mirror the driver sees exactly the picture inverted horizontally; therefore, in order for the sides of the picture on the screen to correspond to the usual view in the mirror, the image coming from the camera has to be “mirrored”.

— Direct / mirror. Cameras capable of operating in any of the picture modes described above. Usually, these are universal models (see “Installation”), which formally refer to the rear view type in our catalog (see above), but also allow front view.