United Kingdom
Catalog   /   Camping & Fishing   /   Air Guns & Weapons   /   Flobert Guns & Starting Pistols

Comparison ZBROIA PROFI 4.5" vs Ekol Major Berg 4.5"

Add to comparison
ZBROIA PROFI 4.5"
Ekol Major Berg 4.5"
ZBROIA PROFI 4.5"Ekol Major Berg 4.5"
from $103.00 up to $125.28
Outdated Product
from $86.40 up to $97.96
Outdated Product
TOP sellers
Main
Steel rifled barrel. Wear resistance of parts and assemblies.
TypeFlobert gunFlobert gun
Form factorrevolverrevolver
Specs
Barrel length4.5 "4.5 "
Caliber4 mm4 mm
Muzzle velocity180 m/sec190 m/sec
Cocking systemauto-cockingauto-cocking
Barrel
rifled /6 grooves/
smooth
Charging capacitymultiply chargedmultiply charged
Type of ammunitionflaubert's cartridgeflaubert's cartridge
Magazine capacity9 pcs9 pcs
Sighting deviceunregulatedunregulated
General
Total length235 mm
Grip material
wood
plastic
 
plastic
Materialmetal
Weight820 g800 g
Added to E-Catalognovember 2013september 2013

Muzzle velocity

Muzzle velocity — that is, the speed of the bullet at the exit from the barrel — provided by the pistol / revolver. Note that for some weapons, the actual muzzle velocity may vary; for more on this, see "Type", and here we note that for such models, the characteristics usually indicate the average value for perfect conditions.

In general, the greater the speed of the bullet, the more long-range the weapon and the higher its penetrating ability. Thus, in some countries this indicator is the basis for legal restrictions on the sale of pneumatics (usually, bona fide sellers have the relevant information). And for airsoft weapons, this moment is important for safety reasons: too high a ball speed increases the likelihood of injury. However, airsoft guns usually give out less than 100 m / s. By the standards of classical pneumatics, this is very little: most short-barreled pneumatics fall in the range of 100 – 125 m / s, in some models the initial speed can reach 125 – 150 m / s and even more.

In "flobers" speeds are higher: an indicator up to 175 m / s is considered relatively low, up to 200 m / s — average, and some long-barreled models give out more than 200 m / s. However, note that we are talking about the speeds claim...ed by the manufacturer, while the actual performance will greatly depend on the characteristics of the cartridge (load, composition, build quality). Therefore, the actual initial speeds in such weapons may differ markedly from those claimed.

Barrel

The type of barrel fitted to the pistol.

Smooth-bore pneumatics in our time is much more common than rifled ; Flaubert revolvers with smooth and rifled barrels on the market are approximately equal; and models for a blank cartridge are equipped exclusively with muffled barrels. Here are the features of each option.

— Smooth. Trunks having a smooth, rifling-free inner surface. The main advantage of this option can be called ease of production and, as a result, low cost. In addition, in the case of pneumatics, the smooth barrel is "omnivorous", with it you can use both bullets and balls (although most often such pistols are compatible with only one type of ammunition). We also note that the airsoft "weapon" in principle is made only with a smoothbore; and the absence of rifling greatly simplifies cleaning, which is especially important for models chambered in Flaubert. On the other hand, in smooth barrels, the bullet is not stabilized by rotation, and the dispersion of such weapons is noticeably greater than that of rifled ones. This does not play a special role in recreational shooting at short distances, however, this type of barrel is not suitable for high-precision weapons.

- Rifled. Barrels with spiral grooves on the inner surface. Due to the rifling, the bullet spins around the longitudinal axis while m...oving along the barrel - this provides additional stabilization and reduces the weapon's own dispersion. Actually, higher accuracy is the main advantage of rifled models over smoothbore ones; and "serious" sports pistols for high-precision shooting are equipped only with this type of barrel. The disadvantages of this option include, first of all, the higher cost than that of smooth ones, as well as the additional difficulty in cleaning - it can be difficult to thoroughly clean the rifling. In addition, in the case of pneumatics, rifled weapons are designed mainly for bullets and are poorly suited for cheaper balls: in most cases their use is not allowed at all, and where allowed, it is desirable to use special soft lead balls. This is due to the fact that the hard metal from which most balls are made wears the rifling a lot; and the promotion of such a charge turns out to be uneven and does not stabilize it, but, on the contrary, leads it away.

- Silenced. A variant found exclusively in pistols chambered in blanks. In such devices, a special plug is installed that blocks the bore and completely eliminates the possibility of firing any projectile (be it a bullet or shot). We emphasize that an attempt to fire from such a “weapon” with a non-blank cartridge (even with a rubber bullet) will most likely lead to a rupture of the barrel and serious injuries to the shooter and people around him.

Total length

The overall length of the weapon is usually from the muzzle to the part protruding farthest back (usually the bottom of the handle). This parameter not only allows you to evaluate the overall compactness of the pistol, but can also be useful for selecting accessories for it — for example, a holster, case or carrying bag.

Grip material

A material used in the finish of a pistol/revolver grip.

The base of the handle is usually made of the same material as the body (see below), however, for additional convenience, the design may include pads that differ in composition from the body. Therefore, the material of the handle (material of the overlays) is specified separately in the characteristics. Also note that many models are available in several finishes at once. As for specific options, they are as follows:

— Plastic. The most popular material nowadays: models with plastic handles make up the majority among pneumatics, and among “floberts” and starting pistols(specifically, models for a blank cartridge almost all have similar handles). This is due to the fact that plastic is quite durable and practical, pleasant to the touch and at the same time inexpensive.

- Wood. Material designed for fans of the classics. The tree has a characteristic appearance, for which it is mainly valued, it is pleasant to the touch, but inferior to plastic in practicality: such handles are more susceptible to scratches, chips and cracks, and at the same time they cost more. Most models with grips made of this material are flaubert revolvers, and most often wood is not the only finish available. But pneumatics in a tree is extremely rare.

- Rubber. Rubbe...r is somewhat softer than plastic, which makes it more pleasant to the touch, moreover, it does not crack even from strong impacts. On the other hand, it has no other noticeable advantages, but it costs much more. Therefore, pneumatics with rubber grips have not received distribution, and most Flaubert revolvers with this feature are available in other finishes.

Material

The material from which the body of the gun is made.

The main materials found nowadays are metal and plastic. At the same time, the division into metal and plastic cases is actually relevant only for pneumatics; models for "flobert" and for a blank cartridge (see "Type") are almost all made of metal. As for the features of each of the materials, they are as follows:

— Metal. The key advantages of metal are strength, reliability and similarity to materials used in firearms. Such cases weigh much more than plastic ones, but this moment is also often referred to as an advantage — it further enhances the resemblance to combat pistols / revolvers, creates a sense of solidity and allows you to effectively practice skills in working with weapons. The main disadvantage of metal is its rather high cost. In addition, note that the composition of this material may be different: in particular, in low-cost models, a lighter and cheaper, but less durable silumin or other similar alloy can be used instead of steel.
Separately, it should be said that in some modern firearms (in particular, Glock) only the casing-bolt is made of metal, and the frame and handle are made of plastic. For air pistols and starting pistols made of similar materials, our catalog also lists metal as the body material in order to emphasize the similarity with combat prototypes.

— Plastic. Material used mainly...in low-cost models of pneumatics. In this case, it means a body made entirely of plastic — including a casing-shutter, if available in the design. The main advantage of this material in this case is its low cost — this determined the specifics of its application. On the other hand, plastic is noticeably inferior to metal in terms of strength and reliability, and the small weight of such cases is considered by many to be a disadvantage — the weapon is perceived as a "toy". However there are also advanced varieties of plastic — durable, heat-resistant, suitable even for military weapons; however, in pneumatics, such materials are used in rather expensive copies of real pistols, where a plastic frame is combined with a metal casing-bolt — and such cases are already considered metal (see above).

Weight

The total weight of the weapon. As a rule, the "empty" weight is indicated in the characteristics, without consumables (bullets / cartridges, cartridges).

This parameter has two meanings. On the one hand, a heavy pistol / revolver is tedious to hold on weight for a long time; in addition, the increase in weight is often associated with an increase in the length of the barrel, due to which the center of gravity shifts forward - and this further increases the inconvenience. On the other hand, massiveness gives an additional resemblance to military weapons and an overall impression of solidity, and in models with blow-back (see above) it also reduces the perceived recoil. Therefore, many consider significant weight to be an advantage rather than a disadvantage.

Note that in models chambered for Flaubert and a blank cartridge, the weight more or less corresponds to military weapons of a similar model or size. In pneumatics, the dispersion can be quite large, especially since not every such pistol is copied from a combat one. It is worth noting here that PCP models are the most massive (see "Type"): due to the built-in tank, the weight of such pistols is usually 1 kg or more. Multi-compression pneumatics are a little lighter - here you can find weapons weighing up to 900 g and even up to 800 g. The maximum figure for AEGs is 900 - 1000 g..., and in the lightest models, the weight does not exceed 700 g. And among the spring-piston and gas-balloon models, almost any weight is found - from small ( less than 600 g) to significant (more than 1 kg).
ZBROIA PROFI 4.5" often compared
Ekol Major Berg 4.5" often compared