Comparison CEM Bart vs CEM Klon

The working length of the barrel installed in the pistol / revolver is from the chamber to the muzzle. In airsoft models (primarily AEGs, see "Type"), the length of the inner barrel is indicated, along which the bullet directly moves. Three main points directly depend on this parameter: the initial velocity of the bullet, the length of the aiming line and the dimensions of the weapon.

In short-barreled (up to 20 – 25 cm) pneumatics and Flaubert's revolvers, a long barrel allows you to achieve higher initial speeds. However there is no rigid dependence here, and models with the same barrel sizes can differ markedly in initial speed (especially since the latter also depends on a number of parameters, primarily the principle of operation — see "Type"). However, long-barreled pistols are generally better for long-range shooting than short-barreled pistols. This is due to the second nuance — the length of the sighting line: a long barrel allows you to increase the distance between the front sight and the whole, thereby reducing errors in aiming. However, with regard to dimensions, the increase in the length of the barrel not only makes the weapon more cumbersome, but also worsens its balance, since the centre of gravity shifts forward because of this.

There are a couple more nuances associated with this indicator. So, in copies of combat pistols (see above), the barrel length is selected in accordance with the size of the weapon from which this model wa...s copied. And for products chambered for a blank cartridge (see "Type"), this parameter is not indicated at all, since there is virtually no full-fledged barrel in such pistols.

Muzzle velocity — that is, the speed of the bullet at the exit from the barrel — provided by the pistol / revolver. Note that for some weapons, the actual muzzle velocity may vary; for more on this, see "Type", and here we note that for such models, the characteristics usually indicate the average value for perfect conditions.

In general, the greater the speed of the bullet, the more long-range the weapon and the higher its penetrating ability. Thus, in some countries this indicator is the basis for legal restrictions on the sale of pneumatics (usually, bona fide sellers have the relevant information). And for airsoft weapons, this moment is important for safety reasons: too high a ball speed increases the likelihood of injury. However, airsoft guns usually give out less than 100 m / s. By the standards of classical pneumatics, this is very little: most short-barreled pneumatics fall in the range of 100 – 125 m / s, in some models the initial speed can reach 125 – 150 m / s and even more.

In "flobers" speeds are higher: an indicator up to 175 m / s is considered relatively low, up to 200 m / s — average, and some long-barreled models give out more than 200 m / s. However, note that we are talking about the speeds claim...ed by the manufacturer, while the actual performance will greatly depend on the characteristics of the cartridge (load, composition, build quality). Therefore, the actual initial speeds in such weapons may differ markedly from those claimed.

The overall length of the weapon is usually from the muzzle to the part protruding farthest back (usually the bottom of the handle). This parameter not only allows you to evaluate the overall compactness of the pistol, but can also be useful for selecting accessories for it — for example, a holster, case or carrying bag.

The material from which the body of the gun is made.

The main materials found nowadays are metal and plastic. At the same time, the division into metal and plastic cases is actually relevant only for pneumatics; models for "flobert" and for a blank cartridge (see "Type") are almost all made of metal. As for the features of each of the materials, they are as follows:

— Metal. The key advantages of metal are strength, reliability and similarity to materials used in firearms. Such cases weigh much more than plastic ones, but this moment is also often referred to as an advantage — it further enhances the resemblance to combat pistols / revolvers, creates a sense of solidity and allows you to effectively practice skills in working with weapons. The main disadvantage of metal is its rather high cost. In addition, note that the composition of this material may be different: in particular, in low-cost models, a lighter and cheaper, but less durable silumin or other similar alloy can be used instead of steel.
Separately, it should be said that in some modern firearms (in particular, Glock) only the casing-bolt is made of metal, and the frame and handle are made of plastic. For air pistols and starting pistols made of similar materials, our catalog also lists metal as the body material in order to emphasize the similarity with combat prototypes.

— Plastic. Material used mainly...in low-cost models of pneumatics. In this case, it means a body made entirely of plastic — including a casing-shutter, if available in the design. The main advantage of this material in this case is its low cost — this determined the specifics of its application. On the other hand, plastic is noticeably inferior to metal in terms of strength and reliability, and the small weight of such cases is considered by many to be a disadvantage — the weapon is perceived as a "toy". However there are also advanced varieties of plastic — durable, heat-resistant, suitable even for military weapons; however, in pneumatics, such materials are used in rather expensive copies of real pistols, where a plastic frame is combined with a metal casing-bolt — and such cases are already considered metal (see above).

The total weight of the weapon. As a rule, the "empty" weight is indicated in the characteristics, without consumables (bullets / cartridges, cartridges).

This parameter has two meanings. On the one hand, a heavy pistol / revolver is tedious to hold on weight for a long time; in addition, the increase in weight is often associated with an increase in the length of the barrel, due to which the center of gravity shifts forward - and this further increases the inconvenience. On the other hand, massiveness gives an additional resemblance to military weapons and an overall impression of solidity, and in models with blow-back (see above) it also reduces the perceived recoil. Therefore, many consider significant weight to be an advantage rather than a disadvantage.

Note that in models chambered for Flaubert and a blank cartridge, the weight more or less corresponds to military weapons of a similar model or size. In pneumatics, the dispersion can be quite large, especially since not every such pistol is copied from a combat one. It is worth noting here that PCP models are the most massive (see "Type"): due to the built-in tank, the weight of such pistols is usually 1 kg or more. Multi-compression pneumatics are a little lighter - here you can find weapons weighing up to 900 g and even up to 800 g. The maximum figure for AEGs is 900 - 1000 g..., and in the lightest models, the weight does not exceed 700 g. And among the spring-piston and gas-balloon models, almost any weight is found - from small ( less than 600 g) to significant (more than 1 kg).