Comparison Zubr Master ZSP-2000 vs Novus J-105 EADHG

Staple models that the tool is compatible with.

Usually, quite specific options are indicated in this paragraph, so finding compatible consumables is not difficult. The specific dimensions of the fasteners should be specified according to the manufacturer's data — different brands use different markings.

The total power consumed by a mains-powered electric tool (see "Power Source"). It is considered the main criterion for assessing the overall capabilities of a particular model: more power leads to better performance. In addition, data on power consumption also allows you to estimate the load on the power grid or other power source; in some cases this is unnecessary.

The actuation method provided in the design of the nail/stapler.

- Contact. This option assumes that direct contact with the material being processed is necessary for operation. Usually, a movable working tip (“nose”) is used for this: until the tool is pressed against the material and the nose is not retracted to the stop, the mechanism will not work. This way of actuation has a positive effect on both efficiency and safety of work: tight contact ensures that the fastener will be hammered as reliably as possible, and the risk that the hammer will “shoot” with a staple or nail in the air is reduced to almost zero. However the need to press the tool tightly every time reduces the speed of work: although pressing takes a fraction of a second, however, on tens and even more hundreds of clogged fasteners, this moment becomes noticeable. On the other hand, many tools provide the ability to hold the trigger so that the stapler automatically fires each time the spout is pressed. But the unequivocal disadvantage of this option can be called the fact that the presence of a safety contact mechanism complicates and increases the cost of the tool.

- Non -contact. Mechanisms that work regardless of whether the tool is pressed against the material or not. Other things being equal, the non-contact method of operation is faster than the contact one, because. does not require additional "body movements" du...ring work. And the tool itself is lighter and cheaper. On the other hand, non-contact triggering requires increased care from the user: if handled carelessly, the tool can trigger at a certain distance from the surface of the material (which impairs clogging efficiency), or even “shoot” in an undesirable direction, which is fraught with material damage and even serious injury .

A device that protects the tool from being triggered at the wrong time.

Most often in a modern tool there are manual fuses in the form of a button or switch. Such a device blocks the release button or opens the power circuit; thus, when the fuse is on, the tool will not work, no matter what the user does. This reduces the chance of fasteners "shooting" in the wrong direction and reduces the risk of personal injury and property damage.

The number of fasteners that fit in the stapler magazine.

Note that manufacturers tend to indicate the maximum number of parts in the characteristics — that is, the capacity for the thinnest fasteners allowed by the design of the tool. Accordingly, fewer larger parts will fit in the store; this must be taken into account when choosing. Nevertheless, this parameter makes it possible to evaluate the instrument and compare models similar in class to each other.

Large capacity, on the one hand, allows you to work longer without interruptions to recharge the stapler. On the other hand, volume magazines are usually very bulky and can weigh a lot on their own, not to mention the weight of the fasteners loaded in them. Also, if parts are charged one at a time, recharging can become quite a long and tedious affair. Therefore, it makes sense to specifically look for a tool for 100 parts or more(especially when it comes to thick fasteners) only if the ability to work for a long time without reloading is more important than the disadvantages described above.

The smallest staple width that the stapler can handle.

The width of the bracket is, roughly speaking, the distance between its legs. Different situations and types of work require different sizes of staples, sometimes quite small. At the same time, staples that are too small will hang out in the store and will not be able to properly fit under the drummer, which is why modern staplers have a minimum size limit. You should pay special attention to it if you plan to work with brackets of small width.

The largest width of staples (see Fastener Type) that the stapler can work with.

The width of the bracket is, roughly speaking, the distance between its legs. Different situations and types of work require different sizes of staples, and sometimes the width must be quite large. However, a staple that is too large simply will not fit into the store, not to mention the fact that the stapler can “shoot” it normally. Therefore, this limit cannot be exceeded, and if you plan to work with brackets, you should pay special attention to the maximum width when choosing.

The smallest length of staples (see Fastener Type) that the stapler can work with.

The length in this case means the length of the leg — in other words, the depth to which the staple clogged "to the stop" penetrates into the material. Small staples do not require much power to drive, but the tool may not be designed for fasteners that are too short due to other parameters — for example, the design of the magazine. Therefore, for many models, this limitation is quite relevant, and in powerful professional models, the minimum length can be quite large — more than 20 mm.

The largest length of staples (see Fastener Type) that the stapler can work with.

The length in this case means the length of the leg — in other words, the depth to which the staple clogged "to the stop" penetrates into the material. This means that working with staples of great length requires not only the appropriate design of the magazine and the feed mechanism — the stapler must also be quite powerful in order to provide the effort necessary for effective clogging. And this, in turn, affects the dimensions, weight and price of the tool. In fact, this means that it does not always make sense to specifically look for a model that can work with long staples — you need to evaluate the specifics of the intended work: often the best choice is a relatively “short”, but at the same time inexpensive and compact tool.

In general, a limit of 10 – 15 mm is typical for entry-level staplers, and in professional models this parameter can exceed 50 mm.