Size
The size of the overhead shower head supplied in the set (see "Complete set"). For round watering cans, this paragraph indicates the size, for other shapes - the length (the largest of the two main sizes).
The larger the overhead shower - the more space it covers, the easier it is to "fit entirely" under the jets and the higher the throughput can be (see "Water consumption overhead shower"). On the other hand, the cost of a watering can directly depends on the dimensions. As for specific figures, the size
up to 20 cm is relatively small, although such watering cans are very popular due to their availability and low consumption. Models
21 - 25 cm can be classified as medium,
26 - 30 cm - relatively large, and the largest watering cans for the overhead shower have dimensions
of more than 30 cm.
Jet settings
The number of settings provided in the hand shower for top shower (see "Complete set").
If you have
several settings, change the jet features and, accordingly, adjust the shower to the user’s wishes. For example, one watering can provide «rain» (ordinary drops of medium size), «waterfall» (stream in the form of water wall) and «stream» (continuous jet under high pressure); there are other modes, their specific set for each model is worth specifying separately. In any case, the more settings - the wider the choice of the user, but the more expensive and more difficult the watering can be on the background of models with
one mode upper shower.
Shape
The shape of a complete watering can of the top shower (see «Type»). From a technical point of view, shape has some influence on shower performance: for example, at the same size (width or diameter)
square upper shower will allow more water than
round shower. However, in practice, the effectiveness of the shower and the sensation of its use are determined by so many different factors that the effect of the shape of the watering on their background is simply lost. Therefore, usually the choice of this parameter is solely due to the aesthetic tastes of the user or the requirements for the design of the bathroom. Therefore, in addition to the round and square form, there are
oval,
rectangular and
non-standard.Water flow
Water consumption during operation of the upper shower (cf. «Equipment»). Indicates the amount of water passing through the watering can with the tap fully open and the water pressure 3 bar (standard household water pressure).
The higher the bandwidth of the watering can be - the more powerful and intense the shower becomes. On the other hand, high water consumption is undesirable if you want to save water - for example, if you have meters installed or if water is supplied from a boiler with a small volume. In addition, it is worth remembering that the watering can have different settings and features of water supply. So, by selecting the lake with the right parameters, you can get a nice and effective top shower even when
low water flow. Actually, a low value in this case is considered to be up to 10 l /min; the average is 10 - 20 l/min, and in the most productive watering can be up to 30 l/min and even more.
Size
The size of the manual or hygienic shower head can be found (cf. «Complete»), which is equipped with a shower system. In fact, it implies the size of the working area - the area on which the nozzles for water supply are located. If this area is round or square, its size is indicated by diameter or width, for other shapes - by length.
Big size allows to cover more space at once; on the other hand, more compact models are more efficient, and cheaper, all other things being equal. And hygienic watering cans, taking into account the specifics of their use, by definition are made
small.
Jet settings
The number of
jet settings provided in the complete manual or hygienic watering can (see "Complete set"). However, hygienic leukemias are usually made
single-mode - this is quite enough considering the application. But in conventional manual waterjets can be several, which allows you to change the characteristics of the jet at the request of the user - for example, instead of the usual thin jets, turn on a hard jet from a single large nozzle or a solid «soft» Flow from water filled with air bubbles. The specific set of settings can be different, it is worth to refine separately. However, in any case, the more options - the wider the choice of the user and the more complicated and more expensive the watering box itself.
Water consumption
The throughput capacity of a manual shower watering agent, in other words, the amount of water it gives out per minute when the faucets are fully open. Since the capacity is not only related to the design of the watering box, but also to the pressure in the water supply, it is customary to specify an average value - at a standard pressure of 3 bar.
The higher this parameter - the more intense the impact on the body can have a shower. At the same time, high water consumption can become a problem when there are water meters or when there are limited supplies - for example, if hot water is supplied by a boiler. Also note that
, low throughput can be compensated by certain jet settings.
Hose length
The length of hose for the shower head be supplied with a shower system of one type or another (see above). In most modern models, this parameter is about 140 - 160 cm - it is enough that even a tall man could easily rinse completely, from the top. In addition, some hoses can stretch 20-30% of their original length. So in practice, it is worth paying attention to the length of the hose except in special cases - for example, if the system is bought for a very spacious bathroom and you need a shower with an increased «radius of action».
Divertor
The diverter is a device by which the flow of water can be switched between individual components of the system - for example, the spill (if it is present) and the shower box, or between the watering can and the upper shower. The design of such a device and the way it is controlled can be different; in modern shower systems, you can find, inter alia, such options:
— Levery. Diverters are in the form of a swivel lever; most often this lever is driven directly by a valve that switches the water flow, but in advanced models there is also an electronic working principle. In any case, lever switches are most popular in modern shower systems: they are very convenient and intuitive to operate, and mechanical diverters of this type are also very simple and inexpensive.
— Push-button. Diverters of this type have the form of a button; but its specific design depends on the features of a particular system. In relatively simple mechanical models (such a majority) the button is also made mechanical, and to switch to the shower watering can be pulled up. And switching to the other side - from the watering box to the drain or the top shower - can often be carried out not only manually, but also automatically, when the water is turned off. Due to this function, the next time the tap opens, the water begins to flow not through the shower hose, which may be in the wrong place, but through the spout or the upper shower, which usually does not cause problems. In some models..., the autoswitch can also be locked at the user’s request (usually by turning the button at the top).
In turn, in advanced electronic devices, such a diverter is made in the form of an electric button, which closes the contacts that control the valve.
— Bend. Rather rare and specific variant: the role of a lever controlling the flow of water, performed directly draining, to the base of which a shower hose is connected. This control usually works as follows: as long as the spout is perpendicular to the mixer housing (that is, directed towards the bath or pan) the water flows through it; and to switch to the shower, the pour is rotated under the mixer. Such devices look interesting, and in use convenient. On the other hand, they are quite complex and expensive, and the flow itself, for a number of reasons, is usually made quite short. Therefore, this option is not available.
— Rotate the drain + push button. The combination in one system of two divers described above. As a rule, the flush turns are responsible for switching the water between the flush and the «shower part», and the button switches between the shower hose and the upper shower. Due to its complexity and cost, this combination is extremely rare.
