Comparison Matteo 1020B 1020x550 vs Blanco Tipo 9E 221093 930x510

The standard way to mount the sink. Some models allow multiple ways to install, at the user’s choice. The specific options may be:

— Mortise overhead. Models fitted in the slot of the worktop in such a way that the side of the sink is significantly above the surface of the worktop. The method of installation is quite simple, but the side raised above the table is in some cases inconvenient.

— Mortise back to back. Models installed in the slot of the worktop so that the side of the sink is at the level of the worktop. Popular due to the ease of installation and convenience in cleaning: if necessary, water and other contaminants can be «driven» by a cloth from the table top directly to the sink. It is true that there is a small gap between the countertop and the sink where pollution can accumulate; but this disadvantage is compensated by the ease of installation.

— Tabletop. Models fixed at the bottom of the countertop - so that the role of the sides actually play the edges of the hole cut under the sink. This method is convenient for maximum convenience in cleaning: from the kitchen table you can easily wipe into the sink spilled liquid or small debris like crumbs, while the contamination will not accumulate in the gap between the sink and the table top (As opposed to butt mounting, see corresponding paragraph. ). At the same time,...the installation of such shells by itself is quite difficult.

— Tabletop module. Quite specific installation method: the sink is installed on the floor top, replacing the table top. For such an installation, it is necessary that the box accurately corresponds to the sink in size, so this option is quite rare.

The presence of a separate additional bowl.

Such a capacity has the form of a small additional bowl (approximately half the main). It can be useful not only for thawing, but also for other tasks - for example, washing fruit or washing pasta through a complete colander (see «Extra»). The convenience of this function is that when using the container - the main bowl remains free and can be used for other purposes: for example, nothing prevents washing the dishes in it.

The presence in the sink of a separate container or a slight depression (a few cm) for thawing and storage of wet products. Characterized by the presence of a drain hole and predominantly compact dimensions, which makes it impossible to use the thawing compartment as an additional bowl.

Availability of space in the sink for the installation of the mixer. This hole can be cut in advance or, if necessary, knocked out during installation (the corresponding place on the model already exists and is made of a softer material).

Type of washing surface made of stainless steel (cf. «Body material»).

— Glossy. Brilliant, mirror surface, distinguished by attractive appearance. On the other hand, on such a surface quickly appear contamination and mechanical damage (traces from dried water, fingerprints, scratches, etc.), so to preserve the appearance it needs to be cleaned regularly, or even polished.

— Matte. The matte surface does not look as bright as glossy - it is fainter, without pronounced reflections. On the other hand, such surfaces are less susceptible to contamination and damage: fingerprints, traces of dried water, scratches and scuffs on such surfaces are not as visible as on gloss.

— Textured. Surface having a relief pattern with a depth of a fraction of a millimeter. This material is most convenient and practical from the point of view of maintenance, it perfectly masks contamination and is well resistant to scratches. The main drawback of textured surfaces is higher cost than matt and glossy. In addition, contamination and bacteria can accumulate in grooves, so clean such sinks should be with special care.

The smallest width of the cabinet, pedestal or other base required for the installation of the sink. By width in this case means the distance between the side walls of the cabinet (base). If the width of the sink is too small, it will not get the necessary support, and its normal use will be impossible.
Main minimum dimensions: >less than 45 cm, 45 cm, 50 cm, 60 cm, 80 cm, more than 80 cm.

There are many national stereotypes: some countries seem more attractive to many users than others. However, in our time these stereotypes are practically grounded. First, in the country of origin of the brand, often only the headquarters of the manufacturer, and the production may be located in another State. Second, the origin from a certain country is not a guarantee of quality: everything depends on how carefully a manufacturer controls its products. Therefore, to assess the quality should be guided not by «nationality», but primarily by the reputation of a particular brand and price category of the product. Among the countries represented are: Germany, Italy, Poland, Romania, Serbia, list", > 3653/href/list."/list/53/pr-36269/">Switzerland, Japan.

The warranty period declared by the manufacturer for this model is the period during which the manufacturer guarantees normal operation. The specific terms of the warranty may vary, however, as a rule, it covers factory defects and malfunctions caused by the fault of the manufacturer/seller and discovered during normal use, without violating the rules.

The longer the warranty period (mostly there are models with a guarantee for 5 years, 10 years, 15 years or even with a lifetime warranty) - the more reliable the sink is, the higher its overall quality, all other things being equal, but the more expensive it will cost in comparison with analogues.

However, depending on the market (country in which it is sold), the warranty for the model may differ. For example, for the countries of the European Union, America and other advanced states, the guarantee can be increased.