Comparison Ferro Ibiza BIB5A vs Ferro Padwa BTP92A

— Straight. Spout that have straight or almost straight shape and directed almost horizontally (other arrangements are highlighted in a separate paragraph — see “At right angle”). Generally, such a spout combines simplicity, practicality, and versatility. In particular, it can be of any length, and can also be rotary (see “Spout”), while being inexpensive to manufacture. Nowadays, straight spouts are extremely popular, and in almost all types of taps (see “Suitable for”). The exception is perhaps the kitchen application: this form is inconvenient for washing dishes by itself and leaves less space for dishes in the sink than other shapes (for example, angled or gooseneck spouts).

— Gooseneck. Taps with a spout in the shape of an arc, usually semicircular and rather steep. This design is most popular in kitchen taps, as it provides the necessary space for washing large dishes. Many models with such a spout are designed for washbasins — they also use a vertical installation, for which the arc is very convenient. And gooseneck bath taps are most often original premium models installed directly on the side of the bath (also horizontally).

— L-shaped. Spout in the shape of the letter “L” — with a vertical base and a horizontal “crossbar” extending from it. Thanks to this shape, the spout can be positioned at a sufficiently high height, which is especially conveni...ent when used in the kitchen or with a washbasin. Most of the L-shaped models refer to these specialization options (see “Suitable for”). According to the type of the tap (see the corresponding list), they are usually single-lever, while the joystick is located on the side; however, there are other options — both in the location of the joystick, and in the type of control.

— U-shaped. Spouts of this category resemble L-shaped models (see the relevant paragraph), in which the end of the spout is noticeably bent downwards. This gives them an original shape, as well as some resemblance to gooseneck models. U-shaped spouts are typically taller and are intended for use in kitchens or washbasins. At the same time, they are not as popular as the mentioned L-shaped ones, and even more so the gooseneck ones. In particular, because of the higher cost with no obvious practical advantages (although this form may well be optimal in terms of design).

— S-shaped. A variant that is predominantly found in bath models (including bath and washbasin solutions) as well as in some kitchen taps. The spout in this arrangement has the shape of the letter “S”, laid “on its side”. This design is well suited for wall-mounted models, where the spout outlet must be placed noticeably below the tap itself.

— At right angle. A straight spout located at a right angle relative to the tap body — directed from the base of the body up or down. This shape is especially suitable for washbasins and kitchens, and it is mainly found in taps of those specializations (see “Suitable for”). Most models with a similar spout have a fairly modern appearance, thanks to that they fit well into modern, high-tech interiors, etc.

— Curved at an angle. A spout that leans upward from the base of the tap and curves slightly downward at the end. The shape is in many ways reminiscent of the “at right angle” option, but it has its own characteristics. Firstly, such a spout can be made somewhat longer, which is convenient for kitchen use: the outlet is at a sufficiently high height and there is enough space under it to wash even large dishes without any problems. Most of the models in this category are just made for the kitchen. Secondly, for some users, this form is preferable from an aesthetic point of view (although, of course, this is a matter of personal taste). These spouts look more “cheap” compared to the products of the “at right angle” form factor and are extremely rare among top plumbing brands.

— Vertical jet. This type of spout is found among bidet taps. It involves vertical spraying of a water jet for taking a hygienic shower after visiting the toilet. The mortise vertical spray module is installed separately from the tap. Usually, the design also assumes a water return valve.

— Connected to overflow. Taps with a spout in the form of a flexible hose that connects to the overflow of the bathtub, and the water is poured through it. Thanks to such taps, minimalism is ensured in the appearance of the bathtub, which is caused by the absence of a classic spout. In addition, there is no need to make extra holes in the side of the bathtub to install the tap.

The length of the spout characterizes the distance from the body to the place where the water is flown out, i.e. the actual length of the conditional "nose" of the tap.

The diameter of the cartridge used in the tap.

The cartridge is called the "heart" of the tap — the part directly responsible for adjusting the pressure and/or temperature of the water (in some models — also for switching between spout and shower). The main dimension of this part is precisely the diameter. However, in fact, this size becomes relevant only if it is necessary to replace the cartridge. But when choosing a tap, it does not really matter — from the point of view of characteristics, only the overall dimensions of the device depend on the diameter of the cartridge, and then quite approximately and without a fundamental difference between individual models.

A feature found in bathtub and shower taps. The switch between the bath and the shower in such models is automated “in one way”: the shower must be turned on manually, and switching to the bath occurs without user participation, when the main tap is closed. In this way, unpleasant situations can be prevented when, after taking a shower, the tap remains switched to a shower, and careless turning on of the water can lead to a “flood”: even if someone forgets to switch the tap, thanks to the shower / bath auto switch, the next time you open it, the water will still flow through the spout.

Country of origin of the brand under which the tap is marketed. Usually, it is indicated by the "homeland" of the manufacturing company or by the location of its headquarters. The brands under which modern mixers are produced come mainly from the following countries (in alphabetical order): Austria, Belgium, Germany, India, Spain, Italy, China, Poland, Russia, Turkey, Czech Republic, Finland, France, Sweden.

There are many stereotypes associated with the “nationality” of brands and products, but most of them have no basis nowadays. First, the actual place of production is often different from the brand's country of origin. Secondly, the quality of the goods depends not so much on geography, but on the policy of a particular company and how carefully this very quality is controlled in it. Therefore, you should pay attention to the country of origin of the brand only if you fundamentally want or (do not want) to support a manufacturer from a certain state. Quality is best judged by the reputation of a particular...brand and the overall price category of the tap.

The warranty period claimed by the manufacturer for a certain tap model is the period during which the manufacturer guarantees the normal operation of the device. The specific terms of the warranty may vary, however, usually, it covers factory defects and malfunctions caused by the fault of the manufacturer or seller and discovered during normal use, without violating the rules; if such defects or malfunctions appear during the warranty period, the manufacturer undertakes the obligation to correct the situation at its own expense — up to replacing the tap with a working one.

Nowadays, you can find taps with a guarantee of 4 years, 5 years, 7 years, 10 years and even 25 years. In general, the longer the warranty period, the more reliable the product is, the higher its overall quality, ceteris paribus, but the more expensive it will cost compared to analogues.