United Kingdom
Catalog   /   Home & Renovation   /   Bathroom & Taps   /   Bathroom & Shower   /   Taps

Comparison Imprese Kucera 55105 vs Volle Daniella 15164300

Add to comparison
Imprese Kucera 55105
Volle Daniella 15164300
Imprese Kucera 55105Volle Daniella 15164300
from $50.40 up to $58.06
Outdated Product
from $55.52 up to $58.20
Outdated Product
TOP sellers
Suitable for
for kitchen
for kitchen
Tap typesingle leversingle lever
Spout
Shaperoundedrounded
Swivel
Jet depth200 mm211 mm
Jet height275 mm274 mm
Water jet angle20 °
Specs
Stop valveceramic
ceramic /Sedal (Spain)/
Water flow7 L/min22 L/min
Installation
Installationdesktop (horizontal)desktop (horizontal)
Mounting holes1 шт1 шт
Mounting hole diameter35 mm35 mm
Inlet communication
hoses
hoses
General
Materialbrassbrass
Finish
chrome
chrome
Tap height365 mm387 mm
Depth236 mm
Country of brand originCzech Republic
Color
Added to E-Catalogseptember 2016december 2016

Jet depth

Distance from the fixing point (for vertically mounted taps) or from the centre of the mounting hole (for horizontally mounted taps) to the middle of the spout. It is a characteristic that determines the "reach zone" of the tap.

Jet height

The jet height is usually specified for taps with horizontal installation (see "Type of installation"). It is measured from the base of the tap to the spout outlet. The large height of the spout is important primarily for kitchen models (see "Suitable for"), because it allows you to place large dishes in the sink. This parameter is directly related to the height of the spout (see above): the height of the jet cannot be greater than the height of the spout. Thus, in fact, one has to find a compromise between the height of the jet and the dimensions of the tap, especially if there is little space for its installation.

Water jet angle

The angle of the water jet produced by the tap, relative to the vertical. Generally stated for full head; with partially blocked water, this angle is smaller. Anyway, the water jet is usually directed towards the user, and the greater the angle of inclination, the farther from the spout the point of incidence of the jet will be placed. However, in most cases this point is not critical; problems can arise only in very cramped conditions, with small basin sizes.

Water flow

The maximum water flow during the operation of the tap, in other words, the maximum amount of water that it can pass through in a minute. This characteristic is important, foremost, for models designed for baths (see "Suitable for"): the greater the throughput, the faster the bath will fill. However, the meaning of this paragraph is not limited to this. First, flow information can be useful in certain calculations related to water supply — for example, to calculate the required pump capacity. Secondly, high-end taps can be equipped with aerators to achieve a powerful and efficient jet with low water consumption; the consumption indicated in the characteristics allows you to evaluate the efficiency of such devices in comparison with analogues.

Tap height

The height of the tap, measured from its base or lowest point to the highest point of the spout. The height of the spout partly determines the installation possibilities — in fact, this is the minimum vertical free space that is required for the tap. In addition, in models with horizontal installation (see "Type of installation"), the spout height is related to the jet height (see below).

Depth

The distance from the extreme front to the extreme back of the tap determines the installation possibilities of the device. In comparison with the depth of the jet, it gives much more visual data precisely on the dimensions of the entire tap, especially for models where there is either no spout (built-in models) or the spout is not the longest part of the set (vertical taps).

Country of brand origin

Country of origin of the brand under which the tap is marketed. Usually, it is indicated by the "homeland" of the manufacturing company or by the location of its headquarters. The brands under which modern mixers are produced come mainly from the following countries (in alphabetical order): Austria, Belgium, Germany, India, Spain, Italy, China, Poland, Russia, Turkey, Czech Republic, Finland, France, Sweden.

There are many stereotypes associated with the “nationality” of brands and products, but most of them have no basis nowadays. First, the actual place of production is often different from the brand's country of origin. Secondly, the quality of the goods depends not so much on geography, but on the policy of a particular company and how carefully this very quality is controlled in it. Therefore, you should pay attention to the country of origin of the brand only if you fundamentally want or (do not want) to support a manufacturer from a certain state. Quality is best judged by the reputation of a particular...brand and the overall price category of the tap.