Comparison Epson EB-E05 vs Epson EB-X05

The lamp model that the projector is designed for. Most projectors come with lamps included, so this information is not needed for normal use. But when looking for a spare lamp or replacement, information about model can be very useful: finding a spare part by the exact name is much easier than by general data like the brand of the projector.

The brightness of the image produced by the projector at maximum backlight brightness. Usually, the average brightness of the screen, derived from a special formula, is indicated. The higher it is, the less the image depends on ambient light: a bright projector can provide a clearly visible image even in daylight, but a dim one will require dimming. On the other hand, increasing brightness reduces contrast and accuracy of colour reproduction.

Accordingly, when choosing this parameter, you need to consider the conditions in which you plan to use the projector. So, for office or school/university use, a brightness of at least 3000 lm is desirable — this allows you to get normal visibility without obscuring the room. In turn, among the top models a very low brightness can be found, because. such projectors are usually installed in rooms specially designed for them with good darkness level. And in ultra-compact devices it is impossible to achieve high brightness for technical reasons.

Detailed recommendations on the optimal brightness for certain conditions can be found in special sources. Here we note that anyway, it is worth choosing according to this indicator with some margin. As mentioned above, as brightness increases, contrast and colour quality decrease, and you may need to use the projector at a reduced brightness to achieve the desired picture quality.

The dynamic image contrast provided by the projector.

Dynamic contrast ratio is the ratio between the brightest white and darkest black colour that a projector can produce. Recall that the quality of colour reproduction and detailing depend on contrast, the higher this indicator, the lower the likelihood that details will be indistinguishable in bright or dark areas. However, dynamic contrast is a rather specific parameter. The fact is that when it is calculated, the brightest white at the maximum brightness settings and the darkest black at the minimum are taken into account. As a result, the figures in this column can be very impressive, but it is impossible to achieve such a contrast within one frame.

By introducing this parameter, the manufacturers went to a certain trick. However, this is not to say that dynamic contrast has nothing to do with image quality at all. Projectors can use automatic brightness control, in which the overall brightness, depending on the "picture" on the screen, can increase or decrease. This format of work is based on the fact that the human eye does not need too bright areas on a general dark background and very dark areas on a bright one, the image is normally perceived even without it. The maximum brightness difference achievable in this mode of operation is exactly what described by dynamic contrast.

The actual maximum frame resolution that the projector is capable of processing and displaying.

Many models allow project images at a higher resolution than the actual resolution of the projector matrix (see above). For example, a 1920x1080 video can be displayed on a device with a frame size of 1024x768. However, the quality of such an image will be noticeably lower than on a projector, which initially has a resolution of 1920x1080.

The maximum resolution is closely related to both the overall picture quality and the size of the projection screen. The higher the resolution, the sharper the image details become. Of course, the screen size itself should be taken into account. The fact is that on a 40-50″ projection surface there will not be much difference between the Quad HD and 4K formats. A high-resolution picture will be able to show itself on a truly large screen.

The closest distance to the screen that the projector can be used on. Typically, this is the minimum distance at which the image from the projector remains in focus.

This parameter is especially important if the device is to be placed at a small distance from the screen (for example, in a cramped room). Some modern projectors are able to work normally at a distance of 10 – 20 cm. Also note that the throw distances are determined primarily by the lens, and if the initial range of these distances does not suit you, perhaps the situation can be solved by replacing the optics.

The farthest distance from the screen that the projector can be used on. This is the maximum distance at which the image remains in focus and maintains acceptable brightness — at least enough for viewing in a darkened room on a high-quality screen.

It is necessary to choose according to this parameter taking into account the expected operating conditions and the distances to be dealt with. At the same time, it's ok to have a certain margin for the maximum distance — since, as already mentioned, it is usually indicated for an perfect screen and a darkened room, and such conditions are not always available. Also note that although the throw distances depend on the lens, not every projector with an interchangeable lens allows the installation of more "long-range" optics than the standard one — the device may simply not have enough brightness for an increased distance.

The magnification range of digital zoom provided by the projector.

It is impossible to increase the diagonal digitally, so in this case we are usually talking about enlarging the image within the existing diagonal. Thus, for example, you can “stretch” a photo or diagram to fill the screen, removing the frames around the edges, enlarge a separate fragment of the image for a more detailed examination, etc. And in some models, digital zoom means, in fact, a reduction, when instead of the entire sensor only part of it is used. This can be useful if the original size of the image does not fit the screen.

It is worth noting that in both cases, the operation of the “zoom” is associated with a decrease in resolution and some deterioration in the overall quality of the picture.

Wi-Fi standard supported by the projector.

Wi-Fi is known mainly as a method of wirelessly connecting to the Internet and local networks. In addition, more recently, this technology has also been used for direct connections between wireless devices. Accordingly, the methods of using Wi-Fi in projectors may also be different. Thus, some models are capable of connecting to local networks to work with content via DLNA (see above); in others, such a connection is used for control from a computer or other network device; in others, a “remote control” like a smartphone or tablet can connect directly via Wi-Fi.

As for Wi-Fi versions, the most popular options in modern technology - Wi-Fi 4 (802.11n) and Wi-Fi 5 (802.11ac) - are quite compatible with each other, and the difference between them in this case is not critical. Therefore, you don’t need to pay much attention to these details when choosing.

There are also Wi-Fi ready projectors, which do not have Wi-Fi out of the box, but when connecting the appropriate adapter (purchased separately) are capable of a wireless connection.

Service connectors for connecting control equipment, provided in the design of the projector. Specific control options in each case may be different, they should be specified separately.

— COM(RS-232). A specialized connector, originally used in computer technology. In general, it is considered obsolete, it is relatively rare among computers, but it is very popular in various specialized equipment.

— USB (slave). Connector for connecting to the USB port of a PC or laptop. With this connection, the projector acts as a peripheral device and can be controlled from a computer. In addition, relatively recently, portable projectors have appeared that are designed for wired connection to mobile gadgets such as smartphones or tablets; they also indicate the USB port (slave), although the specific connection may be different (for example, 8-pin in Apple devices).

— LAN (RJ45). Standard connector for wired connection to computer networks. A projector connected in this way works as a network device, it can be accessed (with appropriate settings) from any local computer. This can be more convenient than using only one control computer. In addition, other features can be implemented through the LAN — for example, DLNA (see the relevant paragraph).

— HDBaseT. A complex interface used mainly in professional equipme...nt (see "Main purpose"). In fact, it is an extended version of the LAN described above, it uses the same connectors and cables, but it has more extensive functionality. In addition to LAN and Internet access, HDBaseT provides dedicated control signals, audio and video streaming, and even power up to 100 W.

— 3D Sync. This port allows you to connect a 3D emitter to the projector, which is necessary for the formation of a volumetric image using active 3D technology (see the relevant paragraph). Accordingly, in order to view a stereo image, it is necessary to use active-type 3D glasses. The glasses are synchronized with the 3D emitter, which makes it possible to achieve a clear and understandable stereo image.