United Kingdom
Catalog   /   Small Appliances   /   Home Appliances   /   Water Filters

Comparison Gejzer 20BB 1 50540 vs Gejzer Jumbo 20BB 32034

Add to comparison
Gejzer 20BB 1 50540
Gejzer Jumbo 20BB 32034
Gejzer 20BB 1 50540Gejzer Jumbo 20BB 32034
from $85.39 up to $99.00
Outdated Product
from $99.00
Outdated Product
TOP sellers
Typemain (without cartridge)main (without cartridge)
Connectionto the water supplyto the water supply
Purpose
for cold water
for cold water
Specs
Number of flasks1
Stages of purification1
Pollution clipping5 µm
Filtration speed60 L/min
Max. operating pressure3 atm6 atm
Max operating temperature40 °C40 °C
More features
Cartridge size20BB (20"x4.5")20BB (20"x4.5")
Fitting size1"
1" /brass insert/
Dimensions60x18.5x18.5 cm60x18.5x18.5 cm
Added to E-Catalogoctober 2016january 2014

Number of flasks

The number of flasks in the filter makes it clear how many water cartridges can be installed in it. For a filter for sink, in most cases there are three flasks. If we are talking about reverse osmosis, then flasks do not mean a membrane, post-filter, etc. since their installation does not provide a separate container. But these types of processing are taken into account in the stages of cleaning. The most obvious difference in the number of flasks is observed in the main filters, where the predominant weight per 1 flask, but there are also models for 2 flasks or even more.

Stages of purification

The number of purification stages provided for in the filter design. At each stage, water passes through its own filter element, clearing itself of certain contaminants; in this case, the steps are arranged in order from coarser cleaning to finer. For example, a three-stage system may look like this: the first stage is mechanical removal of impurities, the second stage is the removal of ferrous, and the third is filtration through a carbon cartridge.

The more stages of purification — the more advanced the filter is considered, the cleaner water it usually provides at the outlet. Accordingly, this moment largely depends on the purpose (see “Type”): for example, multi-stage filtration is quite rare in main models, it is practically not used at all in pre-filters, but the number of stages can reach 9 in models for sink.

Pollution clipping

The smallest size of foreign particles (in microns) that the filter can hold in total. Accordingly, the smaller this size, the higher the filtration efficiency, the less undissolved impurities remain in the filtered water. On the other hand, finer cleaning usually takes more time, which affects the speed (throughput) of the filter. It should be noted that in the case of using reverse osmosis filters, the filtration is very fine, up to 0.01 microns.

Filtration speed

The amount of water that the filter is able to pass through itself per unit of time (of course, effectively purified in the process); usually stated in liters per minute. This parameter is largely related to the type (see above): for example, in jugs, the filtration rate usually does not exceed 0.5 L per minute, while for main devices that supply entire apartments, a throughput of tens or even hundreds of liters is required.

Note that it does not always make sense to pursue a high filtration rate. After all, other things being equal, finer cleaning takes more time; accordingly, the faster the filter works, the higher the chance that the quality of such cleaning will be relatively low. And devices that purify water efficiently and quickly usually have an appropriate price. Therefore, it is worth considering the purpose of the filter and, on the basis of this, determine the balance between the filtration speed and its quality when choosing. It is also worth keeping in mind the conditions of use: for example, if you need to filter low-quality tap water for drinking, it is better to sacrifice speed in favor of efficiency.

Max. operating pressure

The highest inlet water pressure at which a filter connected to a tap or water supply can operate indefinitely (at least until the resource is exhausted, see above) without breakdowns, failures, etc. In other words, this is the ultimate strength of the filter. Therefore, this parameter has a great importance, and when choosing a filter, you must make sure that it meets the characteristics of the connection point. In this case, it is best to choose a model with a margin: although the device will not break from short-term pressure surges in excess of the working device, but this will create off-design loads and can lead to early failure.

When buying a filter for ordinary domestic use, it can be assumed that the maximum pressure in the water supply, provided for by the housing and communal services standards of most post-Soviet countries, represents 6 atm, but its actual value is usually lower. Therefore, 6 atm filters are quite suitable for the definition of a “model with a margin” for apartments with medium and especially low water pressure.
Gejzer 20BB 1 50540 often compared