United Kingdom
Catalog   /   Photo   /   Flashes and On-Camera Light

Comparison Sony HVL-F45RM vs Sony HVL-F43M

Add to comparison
Sony HVL-F45RM
Sony HVL-F43M
Sony HVL-F45RMSony HVL-F43M
Compare prices 1Compare prices 1
TOP sellers
Main
Dust and moisture resistant construction.
Typeregular (classic)regular (classic)
Camera compatibility
Sony
Sony
Specs
Guide number4543
Reload time2.5 с2.9 с
Number of impulses
210 /270 flashes with NiMH batteries/
200
TTLP-TTL, ADI-TTLADI-TTL
Power management++
Beam angle24 - 105 mm24 - 105 mm
Rotary head
Head anglevertically - 158 degrees, horizontally - 180 degreesvertically - 158 degrees, horizontally - 180 degrees
Features
Features
autofocus illumination
camera control
automatic zoom
manual zoom
autofocus illumination
camera control /for cameras: A99, A77, A65, A58, A57, A37, A900, A850, A700, NEX-7, NEX-6, DSC-RX1, DSC-RX1R/
automatic zoom
manual zoom
Wireless control++
Power supply
Power source4xAA4xAA
General
Screen
Screen backlight
Dimensions69.4х113.7х88.3 mm75х140х87 mm
Weight317 g
355 g /without batteries/
Added to E-Catalognovember 2017july 2013

Guide number

The guide number is the main characteristic that describes the power of the light pulse of the flash. It is described as the maximum distance (in metres) at which, at ISO 100 and f/1 lens speed (aperture 1), a flash is able to illuminate an "average" subject sufficiently for a normal exposure; in other words, at what distance from the flash it will be possible to normally shoot the scene at the specified ISO and aperture.

There are formulas by which, knowing the guide number, you can derive the practical shooting distance for each specific value of sensitivity and aperture. The simplest formula used to calculate the distance at ISO 100 is: S=N/f, where S is the distance, N is the guide number, f is the aperture value. For example, for a guide number of 56 and an f/2.8 lens, this distance would be 56/2.8 = 20 m. Increasing or decreasing sensitivity by a factor of 2 would increase or decrease the specified distance by approximately 1.4 times, respectively. If you need to calculate the distance as accurately as possible, you should refer to more detailed formulas that can be found in specialized sources.

Separately, it is worth noting that the leading numbers of flashes, usually, are indicated by manufacturers for specific focal lengths of lenses. This is due to the fact that the shorter the focal length and, accordingly, the wider the viewing angle, the more light is needed to illuminate the scene being shot and the more powerful the flash pulse should b...e (at the same distance). Therefore, when choosing by the guide number, it makes sense to pay attention to the focal length indicated by the manufacturer and select a model with a power reserve — especially since guide numbers are often prescribed for rather “long-range” lenses (with a focal length of about 80-100 mm in equiv. 35 mm).

Reload time

The time it takes the flash or generator (for studio flashes) to prepare for the next flash. The smaller it is, the better. This parameter is especially important for continuous shooting, when the interval between frames is small: if you often shoot in this mode, you should look for a flash with the shortest possible recycle time. Also note that the characteristics usually indicate the shortest recharge time; in some operating modes, it may be significantly more than stated.

Number of impulses

The number of flashes that the flash can fire without recharging the battery or changing batteries (see "Power"). This parameter is very approximate, because. in fact, it strongly depends on a number of factors: pulse duration, use of the display and its backlight (if any, see below), autofocus backlight (see "Features"), etc., and with replaceable batteries — even and on their quality. Often, manufacturers indicate in the characteristics the “perfect”, the maximum possible number of pulses — i.e. with their minimum duration, non-use of additional functions and even the optimal temperature regime for the battery. In reality, this figure may be lower. Nevertheless, the data indicated in the characteristics makes it quite possible to evaluate the battery life of the flash and even compare different models with each other.

TTL

Flash units with TTL support. TTL is an abbreviation for "through the lens", i.e. "through the lens"; this is the name of the method of measuring exposure by the amount of light that passes directly through the camera lens.

In digital photography, TTL works like a pre-flash: before the main exposure, the flash fires one or more test flashes. The amount of light coming from the object being filmed is measured by special sensors, based on these data, the control electronics sets the necessary shooting parameters, after which the actual exposure takes place. This allows you to fine-tune the camera and get an image of optimal quality. The interval between the test and operating pulses is so small that it may not be visible to the naked eye at all (especially when the flash is synchronized with the front curtain or with a slow shutter speed).

Many modern camera manufacturers have their own developments and varieties of TTL technology, respectively, differing in name: for example, Canon has E-TTL and E-TTL II, Nikon has D-TTL (in early models) and i-TTL (in later ones) , Pentax has P-TTL, etc. Support for one or another variety is directly related to the compatibility of the flash with cameras (see above), and different formats are usually not compatible with each other.
Sony HVL-F45RM often compared
Sony HVL-F43M often compared