United Kingdom
Catalog   /   Tools & Gardening   /   Power Tools   /   Power Saws

Comparison Rebir IE-5107G2 vs Rebir RZ2-70-2

Add to comparison
Rebir IE-5107G2
Rebir RZ2-70-2
Rebir IE-5107G2Rebir RZ2-70-2
from $104.20 up to $126.60
Outdated Product
from $116.04 up to $139.92
Outdated Product
TOP sellers
Product typecircularcircular
Typeportableportable
Power sourcemains (230 V)mains (230 V)
Motor
Engine locationtransverselytransversely
Power2150 W2150 W
No load blade speed6400 rpm6000 rpm
Cutting equipment
Bar/blade size205 mm205 mm
Bore diameter30 mm30 mm
Cutting depth65 mm72 mm
Saw angle
45 ° /cutting depth up to 54 mm/
45 ° /cutting depth up to 47 mm/
Features
Features
soft start
stationary installation
soft start
stationary installation
General
Weight6.62 kg6.7 kg
Added to E-Catalogoctober 2012february 2012

No load blade speed

The maximum speed of the disk, provided by a saw of the appropriate design — disk, cut-off, etc. (see "Device").

Note that most of these saws use gearboxes, so that the blade revolutions are much lower than the engine revolutions (see above). This achieves an increase in torque, which in the case of saws is often more important than the high speed of the blade.

As for the specific number of revolutions, it is first of all worth noting that only saws with the same disc diameter can be compared according to this indicator. In these cases, higher speeds provide better performance, but the trade-off is reduced torque; such saws do better with relatively "light" materials. Conversely, low speeds reduce productivity, but allow the blade to effectively "bite" even into dense, stubborn workpieces. More specific recommendations regarding the choice of a saw according to the number of revolutions of the blade can be found in special sources.

Cutting depth

The greatest depth of cut provided by the saw.

In most types of saws (see “Device”), the depth of cut directly depends on both the engine power and the size of the tyre / disk. The specifications give a value for the maximum allowable size of the working nozzle; when using nozzles of a smaller size, the depth of cut, respectively, will be less. But in band saws, this depth is rather weakly related to the actual length of the tape — it is determined primarily by the length of the open section of the tape, which is directly involved in the work.

Anyway, the greater depth of cut makes the tool more versatile, but comes at the cost of weight, price, and electricity/fuel consumption. So when choosing, it is worth considering the real features of the planned work and the dimensions of the workpieces that are planned to be cut. As for specific values, the most modest tools provide a depth of up to 50 mm ; 50 – 75 mm is considered a low indicator, 75 – 100 mm is average, 100 – 125 mm is above average, 125 – 150 mm is already quite an impressive thickness, and the most powerful modern saws can have a cutting depth of more than 150 mm.

Weight

The total weight of the tool. For petrol models (see "Power Source"), usually, dry weight is indicated, excluding fuel.

In general, it makes sense to pay attention to this parameter primarily when choosing a hand tool. At the same time, note that higher power, a more capacious battery or a capacious tank will inevitably affect weight. However, tools with similar characteristics can and do differ markedly in weight. And here it is worth considering that a lighter model will be more comfortable to work with, but weight reduction may affect reliability and/or cost. In addition, a more massive tool is more stable, it is not so prone to jerks under uneven loads. If we talk about specific numbers, then a weight of 3 kg or less is considered very light, 3–5 kg is relatively small, 5–7 kg is medium, 7–10 kg is significant, and some powerful tools (mainly gasoline) weigh and over 10 kg.

As for stationary saws, weight is of secondary importance for them — it mainly affects the ease of transportation.
Rebir IE-5107G2 often compared