Comparison Minelab Go-Find 44 vs Garrett ACE 150

A method used by a metal detector to find items. Describes both the general scheme of the signal and how it is processed.

— VLF. Abbreviation for "very low frequency". As the name implies, these metal detectors operate at relatively low electromagnetic frequencies (less than 20 kHz). They use the “transmitter-receiver” operation scheme: one winding transmits the search signal, the other receives it. The transmitting and receiving windings are located in the same plane, in a concentric pattern or DD (see Coil Type). This technology allows you to create relatively inexpensive devices with good ground balance, minimal sensitivity to false alarms and a high degree of accuracy in metal recognition. Of the shortcomings, it is worth noting the rather high cost of production (coils require precision tuning), as well as the relatively small working depth of such metal detectors.

— VFLEX. A variation of the VLF technology described above, developed by Minelab. The key principles of operation in such metal detectors are the same, however, the control unit in them receives not an analogue, but a digital signal. This has a positive effect on the quality of its processing, but significantly increases the price of the devices themselves.

— R.F. This principle involves the use of high frequencies and the presence of two coils — a receiver and a transmitter — sep...arated by a certain distance (usually several tens of centimeters) and located perpendicular to one another. Such a scheme provides a greater depth of detection, but does not allow you to search for small objects and determine the type of metal. Therefore, it is mainly used in "deep" metal detectors.

— P.I. Abbreviation for "pulse induction" — "pulse induction". In such devices, one coil is provided, "mono" (see "Type of coil"), which plays the role of both a receiver and a transmitter. The coil emits signals in separate pulses, and in between them it works as a receiver, "listening" to the response signal from the ground. Such a scheme allows you to effectively search for objects even in an environment unfavorable for electromagnetic pulses — in particular, highly mineralized soils and in salt water. The latter makes PI instruments extremely useful for marine archeology, both underwater and on wet, salty sand beaches. On the other hand, qualitative discrimination in such models is not available.

— OR. A method based on the so-called breakdown of resonance. The coil in such metal detectors is part of an oscillatory circuit, to which a signal is supplied from the generator with a frequency close to the resonant frequency of the circuit. When a metal object enters the field created by the coil, the characteristics of its inductance and, accordingly, the resonant frequency of the entire circuit change. Based on the change in resonance characteristics, the control unit determines not only the presence of metallic objects, but also, to some extent, their composition. OR-devices are simple in design and inexpensive, since they do not require precision settings; at the same time, the depth of detection and the reliability of operation in them are low, and mineralized or wet soil further worsen the performance. Therefore, this method has not received wide popularity; it is used mainly in entry-level devices.

— ZVT. Minelab's proprietary technology, developed primarily for searching for gold treasures and nuggets. The abbreviation stands for "zero voltage transmission", the principle of operation is described as "the creation of ultra-constant high-power magnetic fields of opposite polarity." Due to this, according to the manufacturer, the efficiency and depth of gold detection are significantly increased, as well as the resistance to interference is improved and it becomes possible to work even on soils with very high levels of mineralization. However, ZVT-metal detectors are quite expensive, and the possibility of working with other metals, except for gold, is usually not mentioned in the description of such devices.

The shape of the coil (frame) of the metal detector.

— Round. The traditional form used in almost all types of ground and underwater metal detectors (see "Type"); the only exceptions are models that work according to the RF method (see "Operating principle"). When using concentric coils (see "Coil Type"), this option allows you to create a conical field, which is convenient for pinpointing the location of the find, but reduces the covered area and makes it difficult to search over a large area; models with DD coils do not have this drawback.

— Elliptical. The shape in the form of a longitudinally elongated ellipse allows you to somewhat "stretch" the field created by the metal detector in length. This is especially true for coils of the concentric type — however, such an expansion somewhat reduces the positioning accuracy of individual finds. But in coils of the DD type, where the accuracy is by definition low, the choice between round and elliptical shape is most often not fundamental.

— Rectangular. A specific form used in RF or PI instruments. For technical reasons, it is considered optimal for such devices, but it is practically not found in other types of metal detectors.

— Butterfly. Another option used in DD coils along with the ellipse (see above). In fact, it consists of two elliptical windings..., partially combined and resembling butterfly wings in shape — hence the name. This option is typical mainly for large-sized DD coils; with a large width, it is considered more optimal than an ellipse.

The size of the standard coil (frame) of the metal detector. Theoretically, the larger it is, the deeper the device is able to “see” and the more space it captures in one pass, but the worse it is suitable for searching for small objects and the lower the accuracy with which it localizes them. At the same time, these characteristics depend on so many other factors that in fact, the size of the coil itself affects them very little.

Note that for coils (frames) of an elliptical shape, only one size can be indicated — along the length.

The operating frequency (or frequency range) of the metal detector. This is one of the most important parameters when choosing a device, because the optimal frequency for different cases will be different — depending on the size and material of the items being searched, the characteristics of the soil and other factors. Detailed recommendations on the choice of frequency for each specific situation can be found in special sources; And already on the basis of this information, it is worth choosing a specific model.

Note that the actual frequency at which the metal detector will operate also depends on the installed coil — they are usually made for a specific frequency. Therefore, to use the full capabilities of the device with the ability to adjust this parameter, you may need replaceable coils.

The greatest depth at which a metal detector is guaranteed to be able to detect a metal object. Note that this parameter is most often quite approximate, moreover, somewhat conditional. This is due to the fact that it is usually indicated for an perfect environment (low-mineralized soil, a fairly large object, the material of which optimally matches the frequency of detection of the coil, etc.), and even for such conditions it is difficult to derive an absolutely accurate value. Therefore, in fact, the detection depth is highly dependent on a number of additional factors (from soil characteristics to user skills) and can be significantly less than indicated in the characteristics. Nevertheless, the claimed depth describes the capabilities of the metal detector quite well, and it is quite possible to compare different models with each other.

Note that a large depth not only increases the cost of the device, but can also adversely affect its ability to detect small objects.

The deepest depth at which a metal detector is capable of detecting small coins and other objects of similar size. Many users buy a device with the intention of “hunting” for metal trifles, so manufacturers often indicate this parameter separately in the specifications. Due to the small size of the coins, their detection depth is usually much less than the total maximum detection depth (see above).

The number of individual discrimination programs provided in the design of the metal detector. In this case, discrimination means filtering the detected objects using a discriminator (see above) so that the device does not work on unwanted objects such as pieces of foil, bottle caps, etc. You can also configure such a filter completely manually, but this may require special knowledge and create difficulties for inexperienced users. To avoid this, some models may have preset programs instead of manual settings. Thanks to such programs, the user just needs to select from the list what type of objects the metal detector should react to, and all the necessary settings will be set by the device's electronics.

The number of pre-installed programs for searching for various materials. Their number reflects the capabilities of a particular model, allowing you to start working right off the bat.

Regular metal detector search programs include detection of coins, all metals, jewelry and relics. In some models, this list can be expanded with "Beach" programs, custom (user) detection mode, etc.