Comparison Kral Puncher NP-01 4.5 vs Ataman AP16 412/B (B/C/M) 4.5

Muzzle velocity — that is, the speed of the bullet at the exit from the barrel — provided by the pistol / revolver. Note that for some weapons, the actual muzzle velocity may vary; for more on this, see "Type", and here we note that for such models, the characteristics usually indicate the average value for perfect conditions.

In general, the greater the speed of the bullet, the more long-range the weapon and the higher its penetrating ability. Thus, in some countries this indicator is the basis for legal restrictions on the sale of pneumatics (usually, bona fide sellers have the relevant information). And for airsoft weapons, this moment is important for safety reasons: too high a ball speed increases the likelihood of injury. However, airsoft guns usually give out less than 100 m / s. By the standards of classical pneumatics, this is very little: most short-barreled pneumatics fall in the range of 100 – 125 m / s, in some models the initial speed can reach 125 – 150 m / s and even more.

In "flobers" speeds are higher: an indicator up to 175 m / s is considered relatively low, up to 200 m / s — average, and some long-barreled models give out more than 200 m / s. However, note that we are talking about the speeds claim...ed by the manufacturer, while the actual performance will greatly depend on the characteristics of the cartridge (load, composition, build quality). Therefore, the actual initial speeds in such weapons may differ markedly from those claimed.

The capacity of the magazine provided with the pistol, or the drum installed in the revolver (see "Form factor"). For obvious reasons, it is indicated only for multiply charged models (see "Charging capacity").

Repeatingly charged air pistols / revolvers are conditionally divided into models with magazines up to 15 charges and more than 15 charges. The largest capacity here is airsoft AEGs (see "Type"), copying submachine guns — they are not uncommon in stores for 50 balls or more, and as additional accessories for many models, so-called "bunkers" are produced, where the number there are already hundreds of charges. As for traditional pneumatics, it is worth noting that if the pistol is designed for bullets and balls at the same time (see "Type of ammunition"), then the capacity when using different types of charge may vary — usually, it is higher for balls in such cases, and this figure and indicated in the characteristics as the main one.

As for the weapon chambered for Flaubert, in it the “classic of the genre” is a revolver with a drum for 9, less often for 8 rounds. A greater number of charges is not found — for this the drum would have to be made too bulky; a smaller number — about 5 – 6 rounds — can be found in individual revolvers, as well as models in the form factor of a pistol, where the dimensions of the case do not allow you to install a larger drum. In turn, pistols chamb...ered for blank cartridges usually more or less correspond in terms of magazine capacity to the firearm models from which they are copied; here you can find models that can hold from 5 to 30 charges.

The number of shots on one gas station that an air pistol or revolver is capable of producing. Specified for gas models and PCP (see "Type"); in the first case, the data is usually given for a standard 12-gram cartridge with carbon dioxide, in the second case, for a full filling of the built-in reservoir.

Note that this parameter is quite approximate, since the actual number of shots at a gas station may differ slightly from the claimed one. Nevertheless, according to the claimed number of shots at a gas station, it is quite possible to evaluate different models of pneumatics and compare them with each other. However it must also be taken into account that the last portions of gas / air pressure is noticeably reduced — and this reduces the initial velocity of the bullet and the firing range, and can also lead to problems in the operation of blow-back systems (see below). So if the number of shots from one gas station is important for you, you should proceed from the fact that the number of “effective” shots (with full bullet speed) will be somewhere 10-15% less than the maximum claimed.

The presence of a mount for an additional sight in the design of a pistol / revolver.

Such mounts are placed at the top of the weapon and are intended primarily for optical and collimator sights. The most popular type of fastening in short-barreled pneumatics is the Weaver / Picatinny rail: it has a T-shaped profile and characteristic transverse slots for rigid fixation of installed accessories. Formally, Weaver and Picatinny rails are different types of seats; however, most sights available on the civilian market are compatible with both variants at once, so these types of mounts are usually not separated.

The bulk of weapons with a scope mount are two types of pneumatic pistols: powerful long-range models for high-precision shooting, as well as copies of military weapons, mainly submachine guns (including those intended for airsoft). In Flaubert's revolvers, additional mounts are almost never used: it does not make much sense to install optics / collimators on such weapons due to the small effective range. And in pistols chambered for a blank cartridge, the sight rail can be provided solely as a decorative element that enhances the external resemblance to military weapons; such a “mount” can even be a dummy that does not correspond to standard sizes and is not suitable for placing sights (which, however, is not a drawback in this case).

The presence of an additional mount under the barrel of a pistol / revolver.

Such a mount usually takes the form of a characteristic bar with transverse slots (Weaver / Picatinny standard or similar). It is designed to install various optional accessories; the classic variants of such accessories are the underbarrel flashlight and the laser designator.

Note that nowadays you can find both pneumatic weapons with underbarrel mounts, and pistols chambered for a blank cartridge (see "Type") with this feature. Moreover, in the second case, the mount plays a predominantly decorative role, giving the “weapon” a resemblance to a combat prototype; however, it can also have quite a practical meaning. For example, by installing an underbarrel flashlight on a starting pistol, you can train basic skills (moving, aiming, reaction to a shot) for actions in low light conditions. However if you are planning such an application, before buying, it's ok to make sure that the selected pistol provides for exactly the standard mount, and not an external imitation, unsuitable for installing a “body kit”.

The overall length of the weapon is usually from the muzzle to the part protruding farthest back (usually the bottom of the handle). This parameter not only allows you to evaluate the overall compactness of the pistol, but can also be useful for selecting accessories for it — for example, a holster, case or carrying bag.

A material used in the finish of a pistol/revolver grip.

The base of the handle is usually made of the same material as the body (see below), however, for additional convenience, the design may include pads that differ in composition from the body. Therefore, the material of the handle (material of the overlays) is specified separately in the characteristics. Also note that many models are available in several finishes at once. As for specific options, they are as follows:

— Plastic. The most popular material nowadays: models with plastic handles make up the majority among pneumatics, and among “floberts” and starting pistols(specifically, models for a blank cartridge almost all have similar handles). This is due to the fact that plastic is quite durable and practical, pleasant to the touch and at the same time inexpensive.

- Wood. Material designed for fans of the classics. The tree has a characteristic appearance, for which it is mainly valued, it is pleasant to the touch, but inferior to plastic in practicality: such handles are more susceptible to scratches, chips and cracks, and at the same time they cost more. Most models with grips made of this material are flaubert revolvers, and most often wood is not the only finish available. But pneumatics in a tree is extremely rare.

- Rubber. Rubbe...r is somewhat softer than plastic, which makes it more pleasant to the touch, moreover, it does not crack even from strong impacts. On the other hand, it has no other noticeable advantages, but it costs much more. Therefore, pneumatics with rubber grips have not received distribution, and most Flaubert revolvers with this feature are available in other finishes.

The total weight of the weapon. As a rule, the "empty" weight is indicated in the characteristics, without consumables (bullets / cartridges, cartridges).

This parameter has two meanings. On the one hand, a heavy pistol / revolver is tedious to hold on weight for a long time; in addition, the increase in weight is often associated with an increase in the length of the barrel, due to which the center of gravity shifts forward - and this further increases the inconvenience. On the other hand, massiveness gives an additional resemblance to military weapons and an overall impression of solidity, and in models with blow-back (see above) it also reduces the perceived recoil. Therefore, many consider significant weight to be an advantage rather than a disadvantage.

Note that in models chambered for Flaubert and a blank cartridge, the weight more or less corresponds to military weapons of a similar model or size. In pneumatics, the dispersion can be quite large, especially since not every such pistol is copied from a combat one. It is worth noting here that PCP models are the most massive (see "Type"): due to the built-in tank, the weight of such pistols is usually 1 kg or more. Multi-compression pneumatics are a little lighter - here you can find weapons weighing up to 900 g and even up to 800 g. The maximum figure for AEGs is 900 - 1000 g..., and in the lightest models, the weight does not exceed 700 g. And among the spring-piston and gas-balloon models, almost any weight is found - from small ( less than 600 g) to significant (more than 1 kg).