United Kingdom
Catalog   /   Camping & Fishing   /   Air Guns & Weapons   /   Flobert Guns & Starting Pistols

Comparison Latek Safari Sport vs Alfa 441 4"

Add to comparison
Latek Safari Sport
Alfa 441 4"
Latek Safari SportAlfa 441 4"
from $140.40
Outdated Product
from $253.80 up to $356.40
Outdated Product
TOP sellers
Main
Barrel, drum and USM made of steel. Adjustment of smoothness of descent of a cock. Rifled stem.
TypeFlobert gunFlobert gun
Form factorrevolverrevolver
Specs
Barrel length16.8 "4 "
Caliber4 mm4 mm
Muzzle velocity160 m/sec180 m/sec
Cocking systemauto-cockingauto-cocking
Barrelrifledrifled
Charging capacitymultiply chargedmultiply charged
Type of ammunitionflaubert's cartridgeflaubert's cartridge
Magazine capacity9 pcs9 pcs
Sighting deviceunregulatedadjustable
Fuse
General
Total length835 mm231 mm
Grip material
wood
 
wood
plastic
Materialmetal
Weight1000 g860 g
Added to E-Catalogdecember 2014september 2013

Barrel length

The working length of the barrel installed in the pistol / revolver is from the chamber to the muzzle. In airsoft models (primarily AEGs, see "Type"), the length of the inner barrel is indicated, along which the bullet directly moves. Three main points directly depend on this parameter: the initial velocity of the bullet, the length of the aiming line and the dimensions of the weapon.

In short-barreled (up to 20 – 25 cm) pneumatics and Flaubert's revolvers, a long barrel allows you to achieve higher initial speeds. However there is no rigid dependence here, and models with the same barrel sizes can differ markedly in initial speed (especially since the latter also depends on a number of parameters, primarily the principle of operation — see "Type"). However, long-barreled pistols are generally better for long-range shooting than short-barreled pistols. This is due to the second nuance — the length of the sighting line: a long barrel allows you to increase the distance between the front sight and the whole, thereby reducing errors in aiming. However, with regard to dimensions, the increase in the length of the barrel not only makes the weapon more cumbersome, but also worsens its balance, since the centre of gravity shifts forward because of this.

There are a couple more nuances associated with this indicator. So, in copies of combat pistols (see above), the barrel length is selected in accordance with the size of the weapon from which this model wa...s copied. And for products chambered for a blank cartridge (see "Type"), this parameter is not indicated at all, since there is virtually no full-fledged barrel in such pistols.

Muzzle velocity

Muzzle velocity — that is, the speed of the bullet at the exit from the barrel — provided by the pistol / revolver. Note that for some weapons, the actual muzzle velocity may vary; for more on this, see "Type", and here we note that for such models, the characteristics usually indicate the average value for perfect conditions.

In general, the greater the speed of the bullet, the more long-range the weapon and the higher its penetrating ability. Thus, in some countries this indicator is the basis for legal restrictions on the sale of pneumatics (usually, bona fide sellers have the relevant information). And for airsoft weapons, this moment is important for safety reasons: too high a ball speed increases the likelihood of injury. However, airsoft guns usually give out less than 100 m / s. By the standards of classical pneumatics, this is very little: most short-barreled pneumatics fall in the range of 100 – 125 m / s, in some models the initial speed can reach 125 – 150 m / s and even more.

In "flobers" speeds are higher: an indicator up to 175 m / s is considered relatively low, up to 200 m / s — average, and some long-barreled models give out more than 200 m / s. However, note that we are talking about the speeds claim...ed by the manufacturer, while the actual performance will greatly depend on the characteristics of the cartridge (load, composition, build quality). Therefore, the actual initial speeds in such weapons may differ markedly from those claimed.

Sighting device

The type of sighting device provided in the design of the pistol / revolver.

The vast majority of short-barreled pneumatics, "floberts" and starting pistols are equipped with the simplest mechanical sights in the form of a front sight and a rear sight. In pneumatic weapons, models with adjustable and non-adjustable sights are approximately equal; in Flaubert's revolvers, the possibility of adjustment is somewhat less common than non-adjustable front and rear sights ; and in models for a blank cartridge, in principle, it makes no sense to provide adjustment. There are pistols / revolvers without sights at all.

Here are the general features of different types of scope:

— Unregulated. Front sight and rear sight, fixed motionless and without any additional settings. The advantages of this design are simplicity, low cost and reliability; in addition, such a sight is almost impossible to shoot down due to an accidental impact of the front sight or rear sight on a foreign object. The main disadvantage is the actual impossibility of adjustment, which does not allow adjusting the sights for a change in distance, side wind or deviations due to production errors. On the other hand, for recreational shooting at short distances, these moments are not decisive, and serious factory defects are extremely rare in fact. So i...f maximum accuracy is not critical for you, a non-adjustable sight may be enough.

— Adjustable. Sights with the ability to adjust; however, the specific possibilities of such adjustment may be different. One of the most popular options is to adjust the rear sight in height, for zeroing weapons at a specific distance. For this, a micrometer screw is usually used. Another option is a rear sight with the ability to move horizontally, it is mainly designed to compensate for errors in the design of the weapon itself, which give a lateral displacement of the point of impact. The most advanced models — mostly high-precision sports pistols — allow you to adjust the rear sight on both axes. Anyway, an adjustable sight is more complicated and more expensive than an unregulated one, it may require additional adjustment by the user himself, but with such devices you can achieve maximum shooting accuracy.
Also note that on the market you can find pneumatics equipped with optical or collimator sights; they are also adjustable.

— Is absent. The absence of their own sights is an extremely rare option, found in two varieties of pneumatic and similar weapons. The first is some spring-piston and PCP pistols (see "Type") with long barrels and high muzzle velocity, designed for high-precision shooting. They have sight mounts (see below) or slots for such mounts, allowing the shooter to choose the sights to their taste. The second variety is revolvers (mainly chambered for Flaubert) of miniature size, originally not designed for aimed shooting in the classical sense of these words.

Fuse

The presence of a fuse in the weapon — a device that prevents an unwanted shot.

The specific control format for this function may vary. So, the most popular option is the traditional fuse (most often in the form of a characteristic thumb flag), turned on and off by the shooter exclusively manually. In "breaks" (see "Cocking system") automatic systems can be installed that block the descent after each reload; to make a shot, such a weapon after cocking must be manually removed from the safety lock. There is also another kind of automatic fuse — a key on the handle that does not allow a shot to be fired until the shooter tightly takes the weapon in his hand (as in the Colt M1911 pistol), or a protective mechanism directly on the trigger (as, for example, in Glock pistols), thanks to which the shot occurs only with a clear press on the trigger. (At the same time, pneumatic copies of the Glocks may also have a manual safety — usually in the form of a slider under the barrel).

Note that in addition to providing additional security, the fuse can perform another function — in copies of military weapons, it allows you to practice skills in handling such weapons. In terms of prevalence, models with a fuse make up the majority among air pistols. Some specific types of such weapons are not equipped with this device — in particular, inexpensive spring-piston models, where additional equipment was abandoned in order to reduce cost,...as well as high-end single-shot PCP pistols, designed for experienced skilled shooters. As for weapons under the "flobert" and under blank cartridges, the presence of a fuse in them is typical for most models in the form factor of pistols, but in revolvers, on the contrary, such functionality is rare.

In conclusion, we emphasize that the presence of a fuse does not eliminate the need to strictly observe safety rules when handling weapons.

Total length

The overall length of the weapon is usually from the muzzle to the part protruding farthest back (usually the bottom of the handle). This parameter not only allows you to evaluate the overall compactness of the pistol, but can also be useful for selecting accessories for it — for example, a holster, case or carrying bag.

Grip material

A material used in the finish of a pistol/revolver grip.

The base of the handle is usually made of the same material as the body (see below), however, for additional convenience, the design may include pads that differ in composition from the body. Therefore, the material of the handle (material of the overlays) is specified separately in the characteristics. Also note that many models are available in several finishes at once. As for specific options, they are as follows:

— Plastic. The most popular material nowadays: models with plastic handles make up the majority among pneumatics, and among “floberts” and starting pistols(specifically, models for a blank cartridge almost all have similar handles). This is due to the fact that plastic is quite durable and practical, pleasant to the touch and at the same time inexpensive.

- Wood. Material designed for fans of the classics. The tree has a characteristic appearance, for which it is mainly valued, it is pleasant to the touch, but inferior to plastic in practicality: such handles are more susceptible to scratches, chips and cracks, and at the same time they cost more. Most models with grips made of this material are flaubert revolvers, and most often wood is not the only finish available. But pneumatics in a tree is extremely rare.

- Rubber. Rubbe...r is somewhat softer than plastic, which makes it more pleasant to the touch, moreover, it does not crack even from strong impacts. On the other hand, it has no other noticeable advantages, but it costs much more. Therefore, pneumatics with rubber grips have not received distribution, and most Flaubert revolvers with this feature are available in other finishes.

Material

The material from which the body of the gun is made.

The main materials found nowadays are metal and plastic. At the same time, the division into metal and plastic cases is actually relevant only for pneumatics; models for "flobert" and for a blank cartridge (see "Type") are almost all made of metal. As for the features of each of the materials, they are as follows:

— Metal. The key advantages of metal are strength, reliability and similarity to materials used in firearms. Such cases weigh much more than plastic ones, but this moment is also often referred to as an advantage — it further enhances the resemblance to combat pistols / revolvers, creates a sense of solidity and allows you to effectively practice skills in working with weapons. The main disadvantage of metal is its rather high cost. In addition, note that the composition of this material may be different: in particular, in low-cost models, a lighter and cheaper, but less durable silumin or other similar alloy can be used instead of steel.
Separately, it should be said that in some modern firearms (in particular, Glock) only the casing-bolt is made of metal, and the frame and handle are made of plastic. For air pistols and starting pistols made of similar materials, our catalog also lists metal as the body material in order to emphasize the similarity with combat prototypes.

— Plastic. Material used mainly...in low-cost models of pneumatics. In this case, it means a body made entirely of plastic — including a casing-shutter, if available in the design. The main advantage of this material in this case is its low cost — this determined the specifics of its application. On the other hand, plastic is noticeably inferior to metal in terms of strength and reliability, and the small weight of such cases is considered by many to be a disadvantage — the weapon is perceived as a "toy". However there are also advanced varieties of plastic — durable, heat-resistant, suitable even for military weapons; however, in pneumatics, such materials are used in rather expensive copies of real pistols, where a plastic frame is combined with a metal casing-bolt — and such cases are already considered metal (see above).

Weight

The total weight of the weapon. As a rule, the "empty" weight is indicated in the characteristics, without consumables (bullets / cartridges, cartridges).

This parameter has two meanings. On the one hand, a heavy pistol / revolver is tedious to hold on weight for a long time; in addition, the increase in weight is often associated with an increase in the length of the barrel, due to which the center of gravity shifts forward - and this further increases the inconvenience. On the other hand, massiveness gives an additional resemblance to military weapons and an overall impression of solidity, and in models with blow-back (see above) it also reduces the perceived recoil. Therefore, many consider significant weight to be an advantage rather than a disadvantage.

Note that in models chambered for Flaubert and a blank cartridge, the weight more or less corresponds to military weapons of a similar model or size. In pneumatics, the dispersion can be quite large, especially since not every such pistol is copied from a combat one. It is worth noting here that PCP models are the most massive (see "Type"): due to the built-in tank, the weight of such pistols is usually 1 kg or more. Multi-compression pneumatics are a little lighter - here you can find weapons weighing up to 900 g and even up to 800 g. The maximum figure for AEGs is 900 - 1000 g..., and in the lightest models, the weight does not exceed 700 g. And among the spring-piston and gas-balloon models, almost any weight is found - from small ( less than 600 g) to significant (more than 1 kg).
Alfa 441 4" often compared