Width
Nominal tyre width (section width) in millimetres. This is one of the notation options; in addition to it, there may also be a designation in inches, for more details, see "Width" above.
Width — whether in millimetres or inches — is one of the parameters that determine compatibility with a particular rim (the other parameter is the fit diameter, see above about it). The main criterion for choosing a tyre in width is the manufacturer's recommendations for a given motorcycle model. It is highly undesirable to deviate from these recommendations: although some types of motorcycles (for example, road bikes) allow a width deviation of +/— 10 mm on the rear wheel, such a wheel will still function in a mode that differs from the standard one. On the front wheel, no deviations are allowed at all.
Profile
Tyre profile height. This parameter is specified as a percentage of the profile width (see above).
The higher the profile, the better the motorcycle can carry heavy weight and increased loads when driving on rough roads and the lower its stability at high speeds. Therefore, for high-speed driving on high-quality flat tracks, hard-surface motorcycle tracks, etc. use ultra-low-profile rubber, with a profile height of up to 60%. For most east european roads, given their overall quality, rather low-profile tyres are recommended — 60 — 80%. And tyres with a profile height of more than 80% should be chosen when the key points are not speed, but cross-country ability and resistance to stress.
Now on the market there are tyres with the following profile height:
40%,
50%,
55%,
60%,
65%,
70%,
75%,
80%,
90%,
100%.
Rim diameter
Tyre inner diameter. This value must correspond to the rim diameter of the wheel on which the rubber is planned to be installed — otherwise the installation will not be possible. You can find out the size of the wheel from the documentation for the motorcycle, from the markings on it, according to the characteristics of the old rubber (if the tyres are bought for replacement), in extreme cases, you can measure the diameter of the disk yourself.
Now on the market tyres with the following diameters:
10",
11",
12",
13",
14",
15",
16",
17",
18",
19",
21".
Load index
The load index indicates
the maximum weight load that the tyre can safely carry in normal operation. To shorten the marking, this parameter is denoted by a two-digit number; you can translate this designation into a specific weight in kilograms using special tables.
This value must not be exceeded — otherwise the tyre may burst at any time due to off-design loads. At the same time, when choosing motor tyres for this parameter, it is worth remembering that the load is distributed unevenly between the front and rear wheels. However, the task is facilitated by the fact that motorcycle manufacturers can indicate the minimum or recommended load indices for the front and rear axles in the documentation for their equipment.
Speed rating
The speed rating characterizes the maximum speed at which the tyre maintains performance, in other words, the highest speed at which you can safely drive when using this tyre in normal mode (on the “native” axle, with normal load, etc.). This parameter is indicated by Latin letters, each of which corresponds to its own maximum speed value — for example, a value of 210 km/h is denoted as H. The most modest modern tyres, used mainly for scooters and motocross motorcycles, have the index J (100 km/h), and in high-speed sports models there are models of the
W level (270 km/h).
You should choose a tyre for this parameter based on the recommendations of the motorcycle manufacturer, and if there are no such recommendations, then with a margin of at least 10-15 km/h in excess of the maximum speed with which you plan to ride; this will give an additional guarantee of safety in case of emergency situations. It is technically OK for most motorcycles to use tyres that are less fast than recommended, but in fact this should not be done. And the point is not only that the driver will have to limit the speed of movement — such tyres are generally less durable than high-speed ones and may not tolerate sharp accelerations well.
Tyre type
—
Chamber (TT). Tyres, consisting of a tyre and an internal sealed chamber into which air is pumped. Despite the "double walls", such tyres are inferior in reliability to tubeless ones — they quickly release air when punctured, and in general they have more modest performance characteristics. At the same time, chamber tyres also have advantages: they are insensitive to rim deformations and retain their tightness even when there is a gap between the rim and the tyre. Thus, there are two main areas of application for such tyres today. Firstly, these are spoked wheels, where the rim does not provide tightness and you cannot do without a chamber; such wheels are installed on many east european motorcycles, as well as some choppers. Secondly, tube tyres are used by some extreme riders or long "
enduro " style travel enthusiasts (see "Directionally").
—
Tubeless (TL). Tyres that do not use an inner tube — the air in such models is pumped into the space between the tyre and the wheel rim. This design requires a one-piece rim that does not allow air to pass through, and only works properly on cast wheels, without spokes. On the other hand, the vast majority of modern motorcycles are equipped with such wheels. Tubeless tyres are considered more reliable and safer than tube tyres, they tolerate punctures better (in particular, they hold air longer), and they are easier to rep
...air. Therefore, in general, such tyres are preferable to tube tyres (with the exception of some specific cases described above).
— TT/TL. Tyres that can be installed in both tube and tubeless ways — depending on which option is required in this case, taking into account the type of wheel and application.Design
The design of the tire depends on the arrangement of the cord threads - a special fiber that gives the rubber base additional strength and rigidity.
-
Radial. In radial models, the cord fibers are located across the tire, parallel to its radius. Such tires are not as prone to heating up as diagonal tires, so they can easily provide a high speed rating (see below). At the same time, radial models are poorly adapted to high weight loads, and their profile is generally flatter and lowered. Therefore, a similar design is found mainly in high-speed tires for sports and road use (see “In the direction”), intended for sport bikes and other relatively light equipment. However, enduro class models can also use this option; but among cross-country ones it is practically not used.
-
Diagonal. In bias-ply tires, the fibers are arranged in the form of a characteristic grid, intersecting each other at an angle of about 40–60°. Such tires heat up more when driving than radial tires, which is why they are poorly suited for high-speed driving. On the other hand, the bias-ply design makes it possible to create high-profile tires with a high load index that can withstand driving well on uneven roads. Therefore, this particular option is used in road tires designed for heavy equipment such as choppers and cruisers, as well as in cross-country models.
