Comparison Dahua NVR4216-4KS2 vs Dahua NVR5416-4KS2

The number of USB 3.2 gen1 ports in the design of the registrar. This interface is used to connect various peripheral devices: USB drives for copying files or updating firmware, keyboards, mice, etc.

Specifically, USB 3.2 gen1 is the successor to USB 2.0. It supports higher data transfer (up to 4.8Gbps) and higher power supply.

The total number of LAN ports (RJ-45) provided in the design of the registrar for connecting to an external network.

LAN (RJ-45) is a standard computer network connector. In this case, they can be found both in traditional DVRs that work only with analog cameras, and in NVRs and HVRs. As a rule, the registrar is equipped with one port of this type, however, there are exception models with two or more ports.

Note that many NVRs are supplemented with RJ-45 connectors for connecting cameras and powering them using PoE. Since these ports are not intended for connection of the registrar with an external network, in this case they are not taken into account, but are indicated separately (see the corresponding paragraph).

The number of alarm inputs provided in the design of the registrar.

Alarm inputs allow the recorder to respond to various events and signals from other elements of the security system. For example, a door opening sensor can be connected to such an input, and upon a signal from it, the registrar will turn on the camera above this door. This ensures the automation of the security system and makes it less dependent on the human factor.

The number of alarm outputs provided in the design of the registrar.

Alarm outputs are used to transmit signals from the recorder to other elements of the security system — an alarm siren, electronic locks, spotlights, etc. Thus, the system can automatically respond to events recorded by the registrar — for example, block the doors when moving in the frame.

The maximum data stream in Mbit/s that the NVR is capable of processing when recording and displaying. The throughput parameter is specified as the maximum incoming/outgoing speed, or as the sum of incoming and outgoing streams (total throughput). It is calculated in such a way that the throughput exceeds the total flow of all IP cameras connected to the DVR, and another 25–30% is put in reserve for playing video or viewing it via network access.

Standards (codecs) used by the recorder to compress the recorded video.

This parameter is important when viewing recorded materials on another device — for example, a media centre, into which a "flash drive" with files from the recorder is inserted. For normal viewing, it is necessary that the player supports the appropriate codec — otherwise the video will be displayed with distortion or will not work at all. Technical details on various standards can be found in special sources.

Note that if you plan to view the materials on a computer, you can not pay much attention to this parameter: most modern operating systems have extensive built-in sets of codecs, and if you don’t have the right codec, you can easily find it on the Internet.

The maximum supported resolution of IP cameras with which the NVR is technically capable of working (primarily recording). With rare exceptions, devices record in maximum resolution from all connected IP cameras. However, the limiting factor here is bandwidth (see the relevant paragraph) – depending on the shooting conditions, it may not be enough.

High resolution allows you to get a more detailed image in which fine details are better visible. On the other hand, such videos take up large amounts of disk space, and their support significantly affects the cost of the device.

The number of SATA connectors provided in the design of the registrar.

SATA is the most popular modern interface for connecting internal drives. One connector allows you to connect one hard drive (or other internal media), that is, the number of such connectors is, in fact, the largest number of separate drives that can be installed inside the recorder at the same time. Basic versions can be equipped with one SATA connector or two. More advanced ones have 4 SATA connectors, and already models for serious objects have much greater connectivity.

The largest total storage capacity with which the recorder is able to work correctly. By default, it is indicated only for internal media with a SATA interface (see above), however, in some models, data is also provided separately for external devices connected via eSATA.

Note that the limit on the total capacity follows from the fact that each individual port has its own limit on the capacity of the drive. In this case, the maximum capacity is distributed equally between the ports. This should be taken into account when choosing drives for the registrar: for example, in a 32 TB model with 8 SATA connectors, the limit for each connector will be 32/8 = 4 TB. This means that installing two internal 8 TB disks in such a registrar will not work, although their total capacity will be less than the maximum.