Comparison iJoy Shogun Univ Mod vs Eleaf iJust ECM Battery

Additional functions of the board provided in the electronic battery mod (see "Battery mod").

— Varivolt. Battery mods that allow you to adjust the voltage supplied to the atomizer. Due to this, the power supply changes and, accordingly, the heating power and the general vaping mode are regulated. At the same time, unlike the varivolt (see below), the voltage change in the varivolt is carried out only manually, regardless of the resistance of the atomizer. In fact, this means that if the user wants to get the same power on an atomizer with a different resistance, he will have to reconfigure the varivolt.

— Variwatt. Battery mods with the ability to automatically maintain the specified power supplied to the atomizer. An automated version of varivolts, which is able to automatically adjust to changes in the resistance of the atomizer. The voltage in the variatt is set for a specific resistance of the atomizer; if the resistance changes, then the electronics automatically sets the voltage at the output of the battery mod so that the power remains unchanged. Thanks to this, you can put heaters with different resistances on the battery pack without worrying about reconfiguring the power parameters — the variatt will independently select the desired voltage, keeping the intensity of soaring at the usual level. The main disadvantage of this option compared to...the varivolt is the relatively high cost, and compared to thermal control(see below), the need to choose the power experimentally, by trial and error.

— Variwatt + Varivolt. Battery mods capable of operating in two different modes — varivolt or variwatt, at the request of the user. These modes are described in more detail separately, and their combination in one battery pack can be useful for those who appreciate the advantages of vari-watt, but are not averse to experimenting with vari-volt as well.

— Thermal control + variatt. Battery mods that combine the variatt capabilities described above with the thermal control function. Thermal control allows you to monitor the temperature of the spiral, maintain it at an optimal level and turn off the power when approaching critical heating. The combination of these two adjustments is the most advanced option for today, in fact, eliminating the need for the vaper to manually select the optimal power settings. At the same time, the steam turns out to be pleasant to the taste (both due to its own temperature, and due to the fact that the probability of burning the wick is reduced to almost zero), and the battery charge is consumed in an optimal way. A serious drawback of thermal control, in addition to a rather high cost, is limited compatibility with atomizers: for this function to work correctly, a “head” with a coil made of nickel or titanium is required, and such models are relatively rare, and they are not cheap in themselves.

— Thermal control. Battery mods, the settings of which are limited only by thermal control. This function is described in more detail above; here we note that thermal control itself does not allow controlling the intensity of soaring, therefore this option has not received much distribution.

The ability to update the firmware of an electronic cigarette — more precisely, a battery mod (this is where all the control electronics are usually located).

This feature is most often found in models with advanced adjustments such as wattage or thermal control (see "Battery mod") — simpler devices do not require complex firmware (although there are exceptions). Major manufacturers of electronic cigarettes periodically release software updates for their equipment that improve the quality of work and eliminate errors noticed by consumers. So this feature is highly desirable for a device with extensive functionality and complex electronics.

The smallest resistance of the heating coil of an electronic cigarette.

The meaning of this parameter will be different, depending on which part of the device is in question (see "Type"). So, for atomizers, this parameter is given if spare heaters are supplied in the kit — accordingly, it is indicated for the “head” with the lowest resistance. For a battery mod, this is the smallest resistance that can be connected to it. And in starter kits, the minimum resistance is also usually indicated by the battery mod; low-resistance "heads" in such cases may or may not be included in the delivery.

Anyway, data on the minimum resistance is important in the mutual selection of an atomizer and a battery mod (including when creating custom windings) — connecting an atomizer with too low resistance is fraught with overloads and various unpleasant consequences, up to fire. However, this parameter is of particular importance for lovers of the so-called subohm — soaring at a low heater resistance (up to 1 ohm), which allows you to achieve high steam saturation (when the resistance decreases, the power increases). Not all batteries are capable of working with sub-ohm heaters, so the suitability of a battery mod for such vaping needs to be clarified.

The type of battery that the battery mod is equipped with or designed for (if the battery is not included).

Modern vapes can use both removable and non- removable batteries. The former are convenient in that a dead battery can be quickly replaced with a fresh one, and while one battery is in use, the second can be charged. However, for many vapes with such a power supply, you have to separately purchase both the batteries themselves and “chargers” for them (for more information about this type of batteries, see the “Removable” section). Non-removable elements, in turn, cannot be quickly changed, but they are more compact, immediately included in the delivery package and extremely easy to use: when the charge is exhausted, you do not need to mess with external chargers, just connect the supplied charger (or even just a USB cable). ).

As removable elements in vapes, 3.7-volt cylindrical lithium-ion batteries are mainly used, here are their main sizes:

— 18650. The most popular size of 3.7 V replacement batteries nowadays. Such cells have a diameter of 18 mm and a length of 65 mm, and their prevalence is due to a combination of good performance with relatively compact dimensions. The number of batteries of this type can be different: for models of relatively low power (up to 100 W), one 18650 battery is enough, in more powerful mods there are 2,...and in some models even 3 or more 18650 batteries.

— 20700. The format of replaceable batteries, used much less frequently than 18650 — due to its larger size (diameter 20 mm, length 70 mm). The number of such elements can also be different — from one in relatively low-power models to two or even three.

— 21700. Another relatively rare size of replaceable batteries; has the same length as 20700 (70mm) but larger diameter (21mm). Such elements are used mainly one at a time, vapes for two 21700 batteries are almost never produced.

— 26650. A rather specific size: such elements are the same 65 mm long as 18650, but their diameter is almost one and a half times larger — 26 mm. This provides high capacity and power, but the large size limits the use of this type of power supply, it is found only in single vape models (although there are devices even for two batteries). And in some battery mods for such elements, it is allowed to replace 26650 with 18650 due to the same length.

Built-in batteries, in turn, differ in the technology by which they are made. Nowadays, Li-Ion (lithium-ion) or Li-Pol (lithium-polymer) non-removable batteries are mainly used. They are similar in their main characteristics: they are compact, have a good capacity, lack the "memory effect", but they do not tolerate both frost and heat. The main difference is that in the first variety the electrolyte is liquid, and in the second it is a solid polymer. Thanks to this, Li-Ion cells are somewhat cheaper, and Li-Pol are less sensitive to overloads and safer in emergency conditions.

The battery capacity of an e-cigarette or separately sold battery mod. This parameter is indicated only for models with non-removable batteries (see "Battery type"): replaceable cells can be produced in different capacities.

The larger the battery, the longer you can use the device without recharging the battery. However the actual power consumption and, accordingly, the battery life of different models will be different, therefore, only devices with similar operating voltages and atomizer resistances can be compared in terms of capacity.

In general, if battery life is important to you, it is quite possible to proceed from the principle “the more capacious the battery, the better”; and to save money, you can choose a relatively weak battery. It is also worth mentioning that there are schemes for calculating the optimal battery capacity depending on the power, atomizer resistance, etc.; these schemes can be found in special sources.

The maximum power supplied by the battery.

This is one of the main parameters of the battery pack that determines its compatibility with the atomizer. Starter kits (see "Type"), by definition, include atomizers that are optimally suited to a given battery in terms of power, and this parameter is mainly of reference value. But when choosing components separately, you should pay special attention to it. Higher power allows you to achieve more saturated steam, but only up to certain limits — too much heating leads to a deterioration in taste, and even burning of the wick (which, all the more, does not contribute to improving the sensation of soaring). So the atomizer must normally transfer the power of the battery, otherwise, at best, you will have to constantly limit the power with the help of a varivolt or variwatt (see "Battery mod"), and at worst, normal use will be impossible at all.

Note that for classic evaporator tanks with one spiral, power up to 40 W is considered sufficient; more powerful batteries are designed mainly for advanced serviced models, drip atomizers and bacodrips(see "Type of atomizer") that have more than one coil and, accordingly, are more high consumption in terms of energy consumption. Also note that the actual heating power depends on the voltage, and in fact it may be lower than the claimed one, depending on the resistance of the atomizer. See “Maximum voltage".

This feature is indicated for battery mods that are designed to use removable batteries — usually 18650 or 26650 (see "Battery Type"). However, such batteries are most often not included in the delivery package, they must be purchased separately. This, on the one hand, does not allow using the device “out of the box”, on the other hand, it makes it possible to choose batteries at your discretion, depending on which atomizer is supposed to be used and what battery power is needed.

Actually, the ability to select batteries at the discretion of the user is one of the key advantages of this option over non-removable batteries (see "Battery type"). Another advantage is that you can buy several sets of batteries and quickly change dead batteries for fresh ones (and charge the removed batteries separately without taking up a battery mod for this). On the other hand, the battery mods themselves turn out to be heavier and larger than non-separable counterparts, and with comparable quality of the batteries themselves, they are often even more expensive. In addition, to charge the batteries, you will also need a separate charger — even if there is a microUSB port, it is recommended to use it only as a last resort (see below for more details), and many models do not have such a connector at all.

The presence of a display in the design of an electronic cigarette — more precisely, a battery mod (see "Type"): putting a display on an atomizer does not make sense for a number of reasons, in particular, because there is not enough space there. But on the battery pack, even a small one, it is quite possible to place a screen. Usually this is the simplest monochrome matrix (black and white or in another colour, say, white characters on a blue background), capable of displaying data in one, at most two lines. However, even with such equipment, control becomes more convenient and intuitive: a variety of digital and textual data can be displayed on the screen, for example, the set voltage or power value, operating mode (variatt / varivolt, if both are supported), battery charge, start message and the end of charging, failure notifications, etc. And some models may even provide advanced touch displays (see below)

The material from which the body of the device is made.

This parameter is relevant primarily for battery mods: they can be made from a wide variety of materials, while atomizers do not differ in variety (the standard option is stainless steel, with a few exceptions; see below for details). Actually, for ready-made kits (including POD systems, see "Type"), this paragraph just indicates the material of the battery mod. Here is a more detailed description of specific options:

— Stainless steel. Perhaps the most popular material for electronic cigarettes and their components — of all types and price categories. At a relatively low cost, stainless steel is strong, reliable, durable and not subject to scratches and corrosion. Of the shortcomings of this material, one can only note a rather large weight, but some, on the contrary, consider this moment an advantage: a massive metal case gives the impression of solidity and quality. Also, steel, like any metal, can cool the skin at low air temperatures and slide in the hands; however, in order to avoid all this, various linings (for example, made of rubber or soft-touch plastic) can be provided on the case to eliminate this drawback.

— Zinc alloy. Another fairly popular material, which is actually a compromise between stainless steel and aluminium. Zinc weighs less than steel and costs less than aluminium alloys; at the same time, this...material perfectly resists corrosion and has high strength, which led to its prevalence.

— Aluminium. Perhaps the most advanced metal in terms of practical characteristics: aluminium is light, strong and absolutely insensitive to corrosion. Its main disadvantage is a rather high price, while the described advantages are rarely decisive in comparison with the same steel or zinc. Therefore, aluminium cases are quite rare; at the same time, it is worth noting that this material is found not only in battery mods, but also in atomizers.

— Plastic. Inexpensive material, which also has a small weight and is able to take on a wide variety of colours. However, this is where the advantages of plastic, in fact, are exhausted: in terms of strength and scratch resistance, it is noticeably inferior to metals, and it can melt from strong heat. However there are advanced grades of plastic, but instead of them, most manufacturers prefer to use steel or other metal in vapes. As a result, plastic cases are rare, and mostly among entry-level models.

— Copper. The material used mainly as a design material — to give the case an unusual appearance (copper has a characteristic reddish tint). From the point of view of practical properties, such cases are similar to steel ones — in particular, they are strong, massive and scratch resistant. On the other hand, copper tolerates moisture worse, stains can appear on it even from constant contact with the skin. However, the main drawback of this material is its high price, which determined the specifics of its application.

— Brass. Another metal used primarily for aesthetic rather than practical reasons. It is similar in properties to copper described above and differs only in colour (shades of yellow) and somewhat greater resistance to oxidation (although it all depends on the specific type of brass).

— Wood. Wooden cases look interesting due to the characteristic colours and patterns. At the same time, this material is not very practical: it is prone to cracks and splits from impacts, it is easily scratched, and it can swell and warp from prolonged exposure to moisture. In addition, wooden cases are quite expensive (in part, this is a payment for the style). So, choosing a battery mod in such a design is worth it only in cases where the ability to “stand out from the crowd” is more important for you than the shortcomings described.

— Ceramics, Special high-strength ceramics are highly resistant to wear: such a case is very difficult to scratch, so it looks like new for a long time. On the other hand, this material may crack on impact (whereas metal is more likely to only slightly bend). Therefore, ceramic cases are extremely rare — especially since they are not cheap.