Comparison Pioneer VSX-935 vs Yamaha RX-V6A

A digital-to-analogue converter (DAC) is an indispensable element of any system designed to reproduce digital sound. The DAC is an electronic module that translates sound information into pulses that are sent to the speakers. The technical features of such a conversion are such that the higher the sampling frequency, the better the signal at the output of the DAC, the less it is distorted during conversion. The most popular option in receivers today is 192 kHz — it corresponds to a very high sound quality (DVD-Audio) and at the same time avoids unnecessary increase in the cost of devices.

In this case, the function of automatic adjustment of each individual sound channel in terms of level and delay is implied so that all of them together provide surround sound that best matches the intention of the creators of the film or musical composition. The need for such a setting is due to the fact that practically no room (neither residential, nor even specialized) is acoustically perfect: the sound propagation is affected by the wall material, floor covering, furniture (sofas, wardrobes, etc.) and other factors. Therefore, the technically correct arrangement of the speakers alone does not guarantee a full-fledged surround sound.

Typically, automatic tuning uses a microphone placed at the intended listening position. During the calibration process, the device outputs test sound signals through the acoustics and “listens” to the features of the sound through the microphone, if necessary, independently changing the audio parameters.

Such a function can greatly simplify the preparation for work — after all, the device will carry out the main part of the setup on its own. However, keep in mind that even in the most advanced receiver models, automatic calibration algorithms are not perfect. As a result, it is highly likely that the automatically set parameters will not meet the tastes of demanding audiophiles. In addition, the reliability of the calibration is also highly dependent on the characteristics of the microphone used — and options with high...sound quality can be quite expensive.

Possibility to simulate multi-channel (for example, 5.1) sound in traditional two-channel headphones. For this, a Dolby Headphone decoder is usually used, which processes the sound in such a way that the sound heard in the headphones is perceived as multi-channel — in particular, the intended position of its sources can be determined much more accurately. And considering that modern Hi-Fi class headphones are not inferior in sound quality to acoustics (and are significantly cheaper), this feature may well come in handy even for demanding audiophiles.

The ability of the receiver to output a video signal in 3D format — that is, a "volumetric" image that has three full dimensions (including depth). Since 3D uses the division of the “picture” of the image into two parts (for the left and right eyes), the format of such a signal differs from the usual two-dimensional one, and not every model is able to work with it. Also keep in mind that viewing 3D content requires not only a receiver, but also a TV (or other playback device) with the appropriate screen capabilities.

The possibility of using the receiver for simultaneous transmission of signals from different sources to screens and speakers located in different places (zones). For example, in a large house, you can simultaneously stream a movie from a Blu-ray player to a screen in a large room, a TV show to a TV in the kitchen, and a radio programme to speakers in a library. Another option for using Multi-Zone is entertainment centers with several rooms of different types (for example, a cinema hall, a roller skating rink and a cafe).

the maximum sound power that can be delivered by the power amplifier (if the receiver has one, see "Type") per speaker channel. It is worth noting here that in this case it is customary to indicate the so-called RMS (Rated Maximum Sinusoidal), or rated power. Rated is considered the highest power that the amplifier is guaranteed to be able to produce without interruption for an hour without any failures or breakdowns. Short-term jumps in the signal level can significantly exceed this value, but the main indicator is still the rated power.

The power of the amplifier largely determines the sound volume of the speaker system connected to the device. In fact, the loudness also depends on the characteristics of the speakers — sensitivity, impedance, etc.; however, other things being equal, the same acoustics on a more powerful amplifier will sound louder. In addition, this parameter also affects the compatibility of the speakers and the amplifier — it is believed that the difference in the nominal powers of these components should not exceed 10-15% (and ideally, the powers should generally match). And since different rooms require speakers of different power, this also affects the choice of amplifier for a particular environment; specific recommendations on the ratio of room characteristics and acoustic power can be found in special sources.

Also note that if the amplifier can operate with a load of different resistance (see..."Permissible acoustic impedance"), then for different options the power per channel will be different — the lower the resistance, the higher the power. In the characteristics, in this case, the maximum value of this parameter is usually indicated — that is, the power at the minimum allowable resistance.

This indicator determines the amount of extraneous noise that accompanies the sound output by the receiver's amplifier. It is convenient because it takes into account almost all possible significant noise — both created by the device itself and due to external causes. The higher the signal-to-noise ratio, the lower the noise volume compared to the main signal, the cleaner the amplifier will sound. A reading of 70-80 dB is considered normal for most consumer electronics, but in AV receivers, which are usually premium devices, this can only be called satisfactory. In the most advanced models, this figure can significantly exceed 100 dB.

The lowest impedance of the loudspeakers of the speaker system, with which the amplifier is able to work normally. The nominal impedance of the speakers, also referred to as the term "impedance", is one of the key parameters in the selection of audio system components: for normal operation, it is necessary that the speaker impedance match the characteristics of the amplifier. If the speaker impedance is greater, the sound volume will decrease significantly, if it is less, distortion will appear in it, and in the worst case, even overloads and breakdowns are possible. Therefore, in the characteristics of receivers, it is usually the minimum resistance that is indicated — after all, connecting a load of too low impedance is fraught with more serious consequences than too high.

The ability of the receiver to work in Bi-amping and/or Tri-amping mode.

The basic principle of both of these modes is that the audio signal is divided into several frequency bands (LF and HF for Bi-amping, in the case of Tri-amping, mid frequencies are separated separately), and each band is processed by its own amplifier and output to its own specialized set of speakers. . In this way, a noticeable improvement in sound quality can be achieved. However, note that the specific implementation of this function in AV receivers may be different. The simplest option involves two or three built-in power amplifiers, each of which outputs the entire audio range to its own set of connectors. To such a device, you need to connect an external crossover (frequency filter) or speakers with built-in filters for each frequency band. More advanced receivers may have their own built-in crossovers, in which case only part of the frequency range is output to each amplifier with a set of connectors; this eliminates the need for external frequency filters. However, anyway, to use Bi/Tri-amping, you will need speakers that support this connection format.