Car Subwoofers BOSS

On b W O or fe R 40hz-400hz Rear High Pass 50hz-1.5Khz Front high pass 50hz-7.5Khz.

12 inch subwoofer 4 ohm impedance Blue LED illumination from inside the cone Best suited for 0.65 cubic foot sealed or 1.5 cubic foot ported enclosure Provides more wiring configuration possibilities. If you add subs, the wiring configurations can be easily matched to optimize the amp's power output and the power handling.

Space Saver - The combination of amplifier and subwoofer all into one, makes this ideal for spatially challenged vehicles. With a slim design, there are a few installation options. Embrace the Bass. Built-in Amplifier - A built-in 800 Max watt amplifier powers the subwoofer Pulse Width Modulated - This design controls the output voltage and current precisely by not only removing the output current sensing loss, but also eliminating all secondary feedback circuitry. It increases efficiency, is lighter, smaller reliable Variable Low-Pass Filter - A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily …

Boss Audio Systems BX-10 Subwoofer Ripper Series 350 RMS, 700 Watt max. Factory packaging

Power - 3400 Watts Max x 1 @1-Ohm, 1700 Watts Max x 1 @2-Ohms, 850 Watts Max x 1 @4-Ohms 1 Ohm Stable - Able to continuously power loads of 1 Ohm without encountering difficulties such as overheating. Typically made to power up subwoofers that demand the heavier power load requirements to be able to perform the way they were made to Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage and current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry Strapping Capable - You are able to strap two R3400D amplifiers and double the power that is being sent to your subwoofer(…

Sensitivity SPL (1W / 1m) 86 dB, Resonant Frequency 44 Hz Poly Injection Cone, 2 Inch Copper Voice Coil, Rubber Surround Sealed Enclosure Internal Volume: .75 Cubic Feet 3.9 Inch Mounting Height, 11 Inch Mounting Hole Diameter Dimensions: Depth 13” x Width 13” x Height 4.5”

Sensitivity SPL (1W / 1m) 88 dB, Resonant Frequency 28 Hz Polypropylene & Paper Cone, 2 Inch Aluminum Voice Coil, Rubber Surround Sealed Enclosure Internal Volume: .65 Cubic Feet, Ported Enclosure Internal Volume: 1.5 Cubic Feet 1.5" x 12.5" Slotted Inch Port Dimension , 30 Inch Port Length, 35 Hz Port Frequency Dimensions: Depth 12.5” x Width 12.5” x Height 6.4” 3 Year Platinum Online Dealer Warranty

Boss Audio CXX124DVC 12" 1200 Watt Car Stereo Subwoofer Dual-4 Ohm Sub. Chaos Exxtreme - 12 inch DUAL Voice Coil (4 Ohm) 1200-watt Subwoofer One 12" Woofer with DUAL 4 ohm 2.5" Voice Coil. 1200 Watts MAX 600 Watts RMS Power Handling. 85dB Sensitivity, 32 Hz Resonant Frequency Polypropylene Cone and Rubber Surround. Works in .9 - 1.4 CuFt Sealed or 1.44 - 2.16 CuFt Ported enclosures

1000 Watts MAX / 500 watts RMS 42 Hz frequency response and 88dB sensitivity Aluminium Voice Coil Subwoofer with treated paper membrane and rubber base

Boss R935, 5-Channel Mosfet Power Amplifier, Riot Series + Subwoofer Remote Control, 4 x 80 Watts RMS + 1 x 150 watts @ 4 ohms stereo, 4x 150 Watt RMS + 1 x 300 Watts @ 2 ohm stereo

Single 4-ohm aluminum voice coil subwoofer Treated paper cone and foam surround Works in 0.7 cubic feet sealed or 1.3 cubic feet ported enclosure For ported or sealed enclosure Can be powered by matched amp to achieve a variety of impedances

BUILT-IN AMPLIFIER: A built-in 1200 Max watt amplifier powers the subwoofer PULSE WIDTH MODULATED: This design controls the output voltage and current precisely by not only removing the output current sensing loss, but also eliminating all secondary feedback circuitry. It increases efficiency, is lighter, smaller reliable VARIABLE LOW-PASS FILTER: A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily keep high notes out of your subwoofer(s) HIGH LEVEL INPUTS: Speaker level inputs are commonly referred to as high-level inputs. It will be used to connect the BAB10 to your factory radio or an …