Routers & Trimmers Trend

Cutters are chosen for fast free cutting, when cutting speed takes preference over finish. Cutters with prefix S are Solid Carbide. Cutters of 2.0mm diameter and below should have a maximum of 1.0mm depth of cut per pass. Small diameter tools must be handled with care to avoid breakage. Single flute cutters should not be used in eccentric chucks.

Two flute straight plunging bits General-purpose tool suitable for profiling, rebating and through slotting. Plunge cut when on the move.

Two flute straight plunging bits General-purpose tool suitable for profiling, rebating and through slotting. Plunge cut when on the move.

Two flute straight cutters produce a cleaner finish than the single flute cutters. Suitable for grooving, rebating, mortising and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood, certain hardwoods and hard plastic. Two flutes give a clean finish to cut edges. All cutters above and including 9.5mm diameter, have TCT plunge centre tips.

Combination pierce and trim cutters. Pierce and cut out apertures in laminate worktops. Base of the cutter acting as a guide follower. Single fluted.

Trend C019AX1/4TC Two Flute Cutter 12mm Diameter The Trend C019AX1/4TC is suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. This Cutter has an extended shank length to suit Trend Hinge Jigs. Features: Use on softwoods, hardwoods, MDF, plywood and chipboard. Cutter has a bottom cut feature. Microgranular TC tips ensure perfect sharpness Highly groundtip face maintains its edge PTFE non-stick coated body Extra long shank Suitable for all makes of router Specification: D: 15/32 inch D: 12 mm C: 19 mm C: 3/4 inch OL: 71mm Shank Diameter:1/4 inch

Trend Craft Pro 1/2in shank worktop joint cutter - 12.7mm diameter Two Flute Carbide tips. 12.7mm diameter X 50mm cutting depth; the essential cutter for routing post formed joints with worktop jigs in tops up to 40mm thick. Cut crisp and clean precision fit joints every time; especially suited for use on abrasive chipboard core laminate faced worktops. Bottom cut feature for plunge work including stopped grooving and morticing applications. PTFE coating to minimise heat and resin build up for increased cutter performance and longevity. 1/2in shank for use in bigger routers and heavier applications with 'K'mark shank to ensure safe working practices. Specifications: • Shank Diameter: …

The Trend PH/JIG Pocket Hole Jig is great for fast and accurate joining of timber and plywood, giving strong instant joints. Solid hardened bushes with a variable pitch of 29 to 63mm. Use on timber, MDF, plywood and blockboard. It allows a variety of joints to be created individually. Uses square drive self-tapping screws. Workpiece can be handled immediately after gluing and screwing, creating time-saving benefits. No clamps required. This replacement stepped drill bit for the Pocket Hole Jig has a diameter of 9.5mm (3/8in).

Trend SET/SS11X1/2TC 6 Piece Router Starter Cutter Set 1/2 Inch Shank TCT This six piece cutter set contains a range of Tungsten Carbide Tipped cutters for decorative woodworking. Features: Suitable for various materials such as softwood, hardwood, chipboard, plywood and MDF Excellent value for money Supplied in a robust secure plastic carry case with a handle grip Specification: 1 x Straight 6.3mm dia x 16mm cut 1 x Straight 12.7mm dia x 25mm cut 1 x V-groove 45 deg x 12.7mm dia 1 x Guided round over R6.35mm 1 x Guided round over R9.5mm 1 x Guided ogee R4mm

Trend TR47X1/2TC Roman Ogee 4mm Radius x 15.9mm Cut The Trend TR47X1/2TC Roman Ogee features 2mm micrograin Tungsten Carbide tips, for cutting the most abrasive materials and give extra long life. Features:
- PTFE coated, indicated by distinctive black colouring
- Can be used on hardwood & softwood, fibreboard, plywood and particle board
- Etched dimensions on extra long 40mm shanks, for quick identification
- By raising the cutter, the top quirk is removed  Specification:
- D1:  25.4mm
- C:  5/8 Inch
- C:  15.9mm
- OL:  64mm
- B:  9.5mm
- R1:  4mm
- Shank Diameter:  1/2 Inch

Tungsten Carbide Tipped for abrasive materials such as Chipboard, MDF, Plywood, Hardwoods and Hard Plastics. Two flutes give a clean finish to the cut edges. All cutters are suitable for plunge routers. Cutters above and including 9.5mm have TCT plunge Centre tip

Two fute flush frimming fits with ball bearing guide. To trim plastic or laminate facings. Used extensively in cabinet making and shop fitting. Features and Benefits Highly durable Tungsten Carbide construction Suitable for straight or shaped work Typical Applications Ideal for trimming and bevelling plastic laminate edges

The Trend CraftPro Cutter with two flute carbide TCT tips for cleaner cutting edges and fast clearance of waste in all timber and timber-based materials. With a bottom cut feature. The PTFE coating minimises heat and resin build-up for increased cutter performance and longevity. The 1/4in shank for easy control in smaller routers with 'K' mark shank to ensure safe working practices. Suitable for a wide range of applications such as engraving, grooving, rebating and shallow morticing. Use on softwoods, hardwoods, MDF, plywood and chipboard. The Trend C022 x 1/4 TCT Two Flute Cutter has the following specification Cutting Diameter 12.7mm (1/2in) Cutting Depth 31.8mm (1.1/4in) Overall Length 72.…

Trend C030X1/4TC CraftPro Two Flute Cutter 19.1mm Diameter x  25.4mm Cut
The Trend C030X1/4TC has a microgranular TC tip ensuring the perfect sharpness. It has a diameter of 19.1mm, 1/4 inch shank and a working depth of 25.4mm.Features:
- VERSATILE 2-FLUTE STRAIGHT CUTTERS: Designed for multiple routing tasks like edge trimming, grooving, and rebating; delivers high-quality finishes at slower feed speeds due to limited waste clearance
- TUNGSTEN CARBIDE TIPPED: 2.0mm micro-granular extra-hard tips for prolonged sharpness and cutter durability. Ideal for cutting softwood, hardwood, and man-made timber boards
- PTFE NON-STICK COATING: Its PTFE non-stick coating reduces friction, minimises re…

Trend Bearing Guided Template Profile Cutter for rebating and trimming edges. Extra care must be taken to avoid breakage of the cutter. Two flute carbide TCT tips for clean, professional finish on timber lippings, plastic laminates and veneers. Specially designed PTFE coated bodies to minimise heat and resin build-up and Micro-granular Tungsten Carbide tips ensure a premium finish in hard and soft woods, and abrasive man-made boards such as ply, MDF and chipboard, to meet the needs of the woodworker and tradesman for quality and performance. All Trend router cutters also have a safety & lsquoK&rsquo mark insertion indicator on each shank to ensure a quick and easy set up whether for hand held …

The Trend UNIBASE is a Router Base Adaptor that allows other makes and models of routers to use the Trend Guide Bushes for increased diversity. The Unibase enables routers with non-standard guide bush fittings to accept the range of Trend guide bushes. It will fit directly to most routers. Features:
- Line-up pin used with a 16mm plastic bush to ensure concentricity of the cutter to the guide bush when fitting the sub-base
- Suits collet sizes 1/4 inch, 8mm, 12mm and 1/2 inch Instructions for fitting:
- The line-up pin fits into the collet and is plunged through the router base 
- The line-up bush is fitted into the Unibase and secured
- This is then placed over the line-up pin a…

Tungsten Carbide Tipped for abrasive materials such as Chipboard, MDF, Plywood, Hardwoods and Hard Plastics. Two flutes give a clean finish to the cut edges. All cutters are suitable for plunge routers. Cutters above and including 9.5mm have TCT plunge Centre tip

Two flute straight plunging bits General-purpose tool suitable for profiling, rebating and through slotting. Plunge cut when on the move.

Two flute straight cutters produce a cleaner finish than the single flute cutters. Suitable for grooving, rebating, mortising and drilling. Use Tungsten Carbide tooling when working with abrasive materials such as chipboard, MDF, plywood, certain hardwoods and hard plastic. Two flutes give a clean finish to cut edges. All cutters above and including 9.5mm diameter, have TCT plunge centre tips.