Drill Bits

This drill bit has a hexagonal shank system and works with all drill drivers with a 13-mm chuck. The Auger Bit is ideal for fast drilling-accuracy when producing through-holes, pre-drilling for rafter nails and drilling deep dowel holes in wood. The heavy-duty self-feeding tip pulls the bit through completely, which allows for quick and effortless precision-drilling. Straight holes and a high chip removal rate and increased speed are made possible by the bit's optimised low-friction flute geometry with a solid centre. Its optimised scoring spur and precision-ground main cutting edge produce accurate holes. It is ideal for use in the ancillary building trades, for carpenters and roofers, and …

Osborn Goldex 81504 series jobber drill bits.High Quaility HSS fully ground Titanium Coated Drill point for longer life. Suitable for drilling in steel, cast steel (alloyed and non alloyed), grey cast iron, graphite and malleable cast iron. Specifications • Standards: DIN 338 • Composition: High Speed Steel • Point Angle: 118° • Point Type & Helix Angle: N ~ 30° • Drill Body Tolerance: h8

Ideal for clean accurate drilling in metal, laminates, plastics and wood. Straight shank HSS jobber drill bit

Faithfull Plug Cutters are used in combination with screwsinks to prepare perfectly sized plugs to fill counterbored holes. For best performance, the power drill should be held in a stand. For a perfect grain match use an offcut from the timber being plugged. To ensure an accurate fit we suggest you use the same screwsink from the Faithfull brand. The set of 4 contains sizes No 6, 8, 10 and 12.Cuts Size 13 mm PlugsAdditional Information:• Type: Plug Cutter• Screw Compatibility: 13mm

These Faithfull SDS Plus Chisel Bits are made from drop-forged chrome molybdenum with a heat-treated tempered edge. Molybdenum is ideally suited for chisels because of its known reputation for hardness, toughness and wear resistance. Used mainly for light demolition, chiselling, stripping plaster, mortar chasing, channelling and breaking through brickwork.

Lasts up to 3x longer than a standard drill bitDrilling through reinforced concrete is a tough job, and it has traditionally taken its toll on drill bits. Regular two-cutter bits get stuck in rebar and they eventually break. The Full Carbide Head on the Expert SDS plus-7X is an advanced 4-cutter design made from a single piece of the toughest metal: It doesn’t jam and presents no weakness on impact.Thanks to Bosch Carbide Technology and the Full Carbide Head, the Expert SDS plus-7X lasts far longer than regular hammer drill bits. It punches through rebar effectively so there is no need to stop, re-target or change bits when you strike steel.For construction professionals drilling concrete an…

Crafted from high-speed steel (HSS) with a titanium nitride (TiN) coating, this drill bit offers exceptional durability and heat resistance, ensuring long-lasting performance in a variety of drilling applications. This jobber drill bit is ideal for creating precise and accurate holes in metal, wood, plastic, and other materials. The TiN coating reduces friction and heat buildup during drilling, resulting in smoother drilling and extended tool life. Features & Benefits • Versatile bit for both hand-held and machine drilling • Titanium Nitride Tipped (2mm and above) • Bright finish and conventional point (below 2mm) • DIN 338 • Specially designed 118° Point Angle Specifications …

The Irwin masonry drills bits are designed for fast and efficient drilling in brickwork, concrete and breeze block, especially with cordless drills. They drill up to 60% faster than competitive drill bits whilst maintaining the same high durability. The single flute design ensures faster dust removal for increased drilling speed, with the unique, pressed diamond-ground carbide tip allows for aggressive cutting and the carbide tip design also ensures 20% longer life compared to previous Irwin masonry drill bits. The bits are made with a chrome vanadium body with high carbon content which allows more hardening and a stronger bit for maximum rupture strength.Irwin Masonry Drill Bit for Cordless …

For use with all multi-tooth milling cutters with 6mm bore. Features and Benefits Pilots locate into pre-drilled pilot holes ensuring positional accuracy of the cutter Suitable for 'blind' or 'through' pilot holes, pin will retract into cutter adaptor upon 'bottoming' Notes Short Series = 12mm cutter For 12mm cutters only Long Series = 13 - 52mm cutters

It is compatible with impact drills. The CYL-1 Drill Bit is optimised for drilling in masonry. Its 2-flute U-shape provides good dust removal while its standard carbide tip makes the bit more wear-resistant. This product is intended for use in masonry and limestone. Pack of 1 • Optimised for Drilling in Masonry • CYL-1 Drill Bit is optimised for drilling in masonry • 2-flute U-shape provides good dust removal • Standard carbide tip makes the bit more wear-resistant Specifications: Diameter (D) mm: 6,00 Working length (L1) mm: 350 Total length (L2) mm: 400 Materials: Stone Materials in Detail: Masonry

High quality metal twist drill bits for precise drilling in metal. Made out of high speed steel (HSS). A finely-tuned material elasticity provides for a long service life. Very good concentricity. Tough viscous tempered bits ensure a particularly long service life. The hexagonal shaft ensures very good power transfer. Drive: ¼" hexagon, suitable for holders as per DIN ISO 1173-D 6.3. Features and Benefits: • Twist bit for metal applications • Hex shaft for very good power transfer • HSS = high speed steel with split point • Finely-tuned material elasticity for great durability • Very good concentricity Contents: 848 HSS Metal Twist Drill Bits, 5 x 50 mm

• Ideal for general-purpose drilling into most masonry materials. For use in a 1/2" chuck with percussion. • Supplied in a plastic wallet.Ideal for general-purpose drilling into most masonry materials. For use in a 1/2" chuck with percussion. Supplied in a plastic wallet.Technical Specification:Size: ø18 x 300mmDimensions: Length: 20mm x Height: 377mmWeight: 0.265KgWarranty: Consumable

Milwaukee Hex Shank Flat Drill Bit for fast drilling of big diameters. Suitable for drilling in natural hard and softwood and chipboard. Ideal for door locks, morticing, electrical and plumbing work. 1/4? Hex shank reception for direct insertion into the power tool or for secure chuck grip. Ground centre point for accurate positioning and sharp wings for improved cutting performance. Specifications • Cutting Width: 38mm • Length: 160mm • Pack Quantity: 1Features & Benefits• Fast drilling of big diameters • Suitable for drilling in natural hard and softwood and chipboard • Ideal for door locks, morticing, electrical and plumbing work • 1/4? Hex shank reception …

Osborn Goldex 81504 series jobber drill bits.High Quaility HSS fully ground Titanium Coated Drill point for longer life. Suitable for drilling in steel, cast steel (alloyed and non alloyed), grey cast iron, graphite and malleable cast iron. Specifications • Standards: DIN 338 • Composition: High Speed Steel • Point Angle: 118° • Point Type & Helix Angle: N ~ 30° • Drill Body Tolerance: h8

The HSS Twist Drill Bit Ground is for drilling through metal with maximum precision. The bit's exposed 135-degree self-centring split-point tip combines active cutting and perfect centring without wandering, delivering maximum precision. The split-point tip also eliminates any need to pre-punch or pilot drill for up to 10 mm. This precision-ground bit made of HSS (high-speed steel) enables up to 40% faster drilling rate and up to 50% lower feed pressure than standard-ground HSS drill bits with chisel edges. This bit is designed for drilling holes in alloyed and non-alloyed steel, cast steel, cast iron, sintered iron, malleable cast iron, non-ferrous metals and hard plastics. The HSS Twist Drill …

SDS Drill Bit 12x140x200mmC.K SDS Concrete Drill Bit 12x140x200mm~ Tungsten carbide tipped with optimized geometry for drilling concrete and stone~ Vacuum brazed tips for durability~ Ground flutes designed for optimum debris removal~ SDS-plus shank~ Diameter: 12 mm~ Working length: 140 mm~ Total length: 200 mmTechnical DataDiameter: 12mmWorking length: 140mmOverall length: 200mmComponent Material:Tungsten tipTechnical Specification:CE Certified: NoConflict Materials Content : YesConflict material Country of Origin: GermanyConflict material Name of substance: TungstenREACH Content Status SVHC Free or Contains SVHC: SVHC freeRoSH Regs Within Scope: NoBatteries Included: NoBattery Powered: NoCharger …

Ideal for clean accurate drilling in metal, laminates, plastics and wood. Straight shank HSS jobber drill bit

Irwin Speedhammer Flat Chisels for use with SDS Max machines. Suitable for a wide range of applications: breaking through, breaking up concrete, light demolition work and chasing of channels for pipes and electrical conduit. Suitable for use on concrete and masonry and are supplied in a grey sandblasted professional finish.The Irwin IRW10502187 Speedhammer Max flat chisel has the following dimensions:Size: 25 x 280mmAdditional Information:• Type: Flat Chisel• Size: 280mm

The SDS plus-3 Drill Bit offers durability when drilling in concrete. To prevent heat development, the 4-flute dura design provides effective dust removal for increased endurance. It is made of high-alloy steel, which is produced with an optimised hardening technology to withstand wear. For additional resistance, indented cutting edges are made from an ideal Bosch-controlled carbide blend. As proof of quality, the drill bit bears the test mark of the PGM Masonry Drill Bit Association Board, guaranteeing compliance with tight tolerances, exact drilling and the firm hold of fixings. The bit is intended for work on concrete and masonry and is to be used with rotary hammers with SDS plus holders.…

These Faithfull Professional Cobalt Jobber Drill Bits are manufactured from M35 HSSE grade steel with a 5% cobalt content for increased heat resistance and cutting performance. All bits are fully ground and feature a 135° non-slip split point for precise centring and are produced in accordance to DIN 388 for high precision tolerances and geometric accuracy. Cobalt bits cut faster and last longer and are suitable for heavy-duty industrial work in: Alloy steels, carbon steels, cast iron, hardened alloy steels, stainless steels, high temperature alloys, Titanium alloy, high strength steel and carbon fibre composite materials.These Faithfull Professional Cobalt Jobber Drill Bits are supplied …

The IRWIN® HSS Pro Drill Bits are made from high-performance, high-speed steel. They have a 118° split point shape for increased performance and very good centring. The drill bits ensure precision starting, with no need to pre-punch or pilot drill. They penetrate the material quickly, requiring little effort and feed pressure. Manufactured to DIN 338 standards. DIN 338 drill bits are suitable for many trade and industrial applications in alloyed and unalloyed steel, non-ferrous metal, cast iron and plastics.This IRWIN® HSS Reduced Shank Pro Drill Bit has the following specification: Diameter: 11.0mmWorking Length: 94mmTotal Length: 142mmShank Diameter: 10mmAdditional Information:• …

The Faithfull Bevel Edged Chisel range are quality tools for professional work as well as DIY users. The blue PVC handles on these chisels are impact resistant and designed for use with a mallet or an occasional hammer blow. Each blade is manufactured from drop-forged chrome vanadium steel that is hardened and tempered to exacting standards, ensuring that the cutting edge remains sharper for longer. The bevelled edges make these chisels ideal for fine work and for cutting into tight corners. All the chisels in this range are supplied with blade guards.

Milwaukee HSS-G Thunderweb Drill Bit design is characterised by a conical shaped web which gets thicker towards the back of the drill bit. Standard drill bits have a constant thickness throughout their length. Even at the narrowest point the Tunderweb core is thicker than that of a standard drill bit. Specifications • Cutting Width: 2.3mm • Length: 53mm • Pack Quantity: 10Features & Benefits• Parabolic web cross section: Large web thickness and strength built in • Thunderweb flute form ejects hot chips rapidly • Dissipates heat better increasing life time • Precision starting, drill bit won't walk on material surface • Polished finish reduces friction …

Bahco 9629 Series Flat Bit have a positive cutting angle which drills holes twice as fast and lasts 3x longer than a conventional bit. Made from high-carbon steel and heat-treated all over. The hardened blade is forged directly from the round shaft. Its winged shoulders enable the bit to first cut the wood and then remove the material from the centre section, ensuring a smooth finish and superior swarf clearance. Sizes 10mm and above feature cutting spurs.1 x Bahco 9629-38 Flat Bit 38mmAdditional Information:• Diameter: 38mm• Overall Length: 160mm• Pack Qty.: 1