Drill Bits

Bahco 9629 Series Flat Bit have a positive cutting angle which drills holes twice as fast and lasts 3x longer than a conventional bit. Made from high-carbon steel and heat-treated all over. The hardened blade is forged directly from the round shaft. Its winged shoulders enable the bit to first cut the wood and then remove the material from the centre section, ensuring a smooth finish and superior swarf clearance. Sizes 10mm and above feature cutting spurs.1 x Bahco 9629-40 Flat Bit 40mmAdditional Information:• Diameter (mm): 40• Overall Length (mm): 160• Pack Qty.: 1

These Faithfull chisels are suited to cutting bricks during building work. This chisel has a suitably hardened cutting edge, but should not be used on concrete containing reinforcing bars.

The Milwaukee Hammer Drill Bits have been designed with a 2 cutter carbide tip to allow for drilling into concrete, brick, block and soft material for electrical installations, lighting fixtures and holders. Our Hammer Drill Bits also features a red flute for easy identification along with a wide flute design to remove dust faster, while also reducing heat build-up, resulting in more holes per charge. Specifications • Cutting Width: 10mm • Length: 260mm • Pack Quantity: 1Features & Benefits• Tungsten carbide tipped drill bit allow drilling into concrete, aerated concrete blocks, masonry and granite • Wide red flute for optimal material extraction and easy identifiable …

An economical bit for cutting quick holes in timber. With centre point, back tapered cutting edge and ground chip breakers. Specifications: • Shank Diameter: 1/4 hex • Dia Metric: 16 • Overall Length Metric: 152

Its full carbide head with 5 cutters is fused with IDS welding technology to drill with a very high level of accuracy. A vibration-reduced power transfer from the rotary hammer to the full carbide head is provided by the 2 + 2 flute design, which is made of high-alloy steel and created using optimised hardening technology. This offers the stability necessary for exact results. To prevent wandering and obtain a precise hole diameter, the Activeteq centring tip guides the drill position from the start. The bit is intended for use on masonry, concrete and reinforced concrete. It is compatible with rotary hammers with SDS plus holders. To achieve accurate results, the visibility of the wear mark …

Fast Drilling-Accuracy - The Auger Bit is ideal for fast drilling-accuracy when producing through-holes, pre-drilling for rafter nails and drilling deep dowel holes in wood. The heavy-duty self-feeding tip pulls the bit through completely, which allows for quick and effortless precision-drilling. Straight holes and a high chip removal rate and increased speed are made possible by the bit's optimised low-friction flute geometry with a solid centre. Its optimised scoring spur and precision-ground main cutting edge produce accurate holes. It is ideal for use in the ancillary building trades, for carpenters and roofers, and is suitable for soft and hard wood This drill bit has a hexagonal shank …

Stanley drill bits are designed to resist the impacts and fast drilling on concrete. The flute design removes the debris from the hole contribution for longer drill bit life. The hardened steel construction of the drill bit ensures exceptional strength, allowing it to withstand the toughest drilling applications. Whether you are working on soft or hard surfaces, its reinforced carbide tip provides maximum durability and longevity, ensuring consistent performance throughout projects. Features & Benefits • For drilling into house bricks and masonry • Shank diameter of drill bits 10-13mm is reduced to 9.5mm • Diameters larger than 13mm shank is reduced to 12.7mm • For use with …

These Faithfull SDS Plus Chisel Bits are made from drop-forged chrome molybdenum with a heat-treated tempered edge. Molybdenum is ideally suited for chisels because of its known reputation for hardness, toughness and wear resistance. Used mainly for light demolition, chiselling, stripping plaster, mortar chasing, channelling and breaking through brickwork.

Ideal for clean accurate drilling in metal, laminates, plastics and wood. Straight shank HSS jobber drill bit

A great and versatile all-around drill with a 118° conventional point, which provides strength and is easy to regrind, making it very cost-effective. Usable for hand-held and machine drilling. Steam tempered finish retains cutting fluid and prevents chip tool welding. Suitable for many materials. Features and Benefits: • Shank: Cylindrical shank Specifications: Hand (Cutting direction): Right Cutting diameter tolerance class (TCDC): h8 Basic standard group (BSG): DIN 338 Material code (BMC): High Speed Steel Point Angle (SIG): 118° Material Application Priority Usage: K - Cast Iron, P - Steel and cast steel Country of origin: Brazil Spiral form: Standard Spiral Coating: Steam Tempered Br…

The CWCL TCT series Pilot Pins are compatible with Rotabroach TCT cutters from 66mm to 100mm diameter and 50mm depth of cut.

The IRWIN® SDS Speedhammer Plus Drill Bits are designed for SDS drilling. They drill exceptionally fast into brick, block, masonry, concrete and granite. The patented, unique single flute design ensures efficient, speedy removal of dust and lower vibrations and 28% greater capacity meaning more efficient waste removal. They have a patented extra-short drill bit head which means the head takes 80% of the workload, ensuring higher durability and speed. Clears drilling dust directly into the flute, reducing the risk of clogging. The bits have 25% more tungsten carbide for extra strength and they drill 25% faster than competitive drill bits with the same high durability. In addition, they have …

Lasts up to 3x longer than a standard drill bit - Drilling through reinforced concrete is a tough job, and it has traditionally taken its toll on drill bits. Regular two-cutter bits get stuck in rebar and they eventually break. The Full Carbide Head on the EXPERT SDS plus-7X is an advanced 4-cutter design made from a single piece of the toughest metal: It doesn’t jam and presents no weakness on impact. Thanks to Bosch Carbide Technology and the Full Carbide Head, the EXPERT SDS plus-7X lasts far longer than regular hammer drill bits. It punches through rebar effectively so there is no need to stop, re-target or change bits when you strike steel. For construction professionals drilling concrete an…

For use with all multi-tooth milling cutters with 6mm bore. Features and Benefits Pilots locate into pre-drilled pilot holes ensuring positional accuracy of the cutter Suitable for 'blind' or 'through' pilot holes, pin will retract into cutter adaptor upon 'bottoming' Notes Short Series = 12mm cutter For 12mm cutters only Long Series = 13 - 52mm cutters

Lasts up to 3x longer than a standard drill bit - Drilling through reinforced concrete is a tough job, and it has traditionally taken its toll on drill bits. Regular two-cutter bits get stuck in rebar and they eventually break. The Full Carbide Head on the EXPERT SDS plus-7X is an advanced 4-cutter design made from a single piece of the toughest metal: It doesn’t jam and presents no weakness on impact. Thanks to Bosch Carbide Technology and the Full Carbide Head, the EXPERT SDS plus-7X lasts far longer than regular hammer drill bits. It punches through rebar effectively so there is no need to stop, re-target or change bits when you strike steel. For construction professionals drilling concrete an…

High quality metal twist drill bits for precise drilling in metal. Made out of high speed steel (HSS). A finely-tuned material elasticity provides for a long service life. Very good concentricity. Tough viscous tempered bits ensure a particularly long service life. The hexagonal shaft ensures very good power transfer. Drive: ¼" hexagon, suitable for holders as per DIN ISO 1173-D 6.3. Features and Benefits: • Twist bit for metal applications • Hex shaft for very good power transfer • HSS = high speed steel with split point • Finely-tuned material elasticity for great durability • Very good concentricity Contents: 848 HSS Metal Twist Drill Bits, 3.3 x 40 mm

Faithfull Tri-Point Speed Auger Bits will drill fast and clean holes in all types of wood. The three spurs and cutting edges create perfectly round holes with less chance of binding in the workpiece. Three flutes offer efficient waste removal making them much faster than traditional bits. A self-feeding screw tip enables accurate centring and pulls the bit through the wood. Precision machined from high-quality carbon steel with ground and honed cutting edges. The quick-release 1/4in hex shank is impact rated for use in impact drivers as well as all other corded and cordless drills. Specification Overall Length 159mm

The SDS plus-5 Drill Bit allows for effortless drilling. For smooth work, the carbide plate is grooved and bears notches that penetrate material more easily and prevent jamming in concrete. Drill guidance for easy starts without jarring or wandering is provided by the Activeteq centring tip, which keeps the drill in place for a precise hole diameter. Furthermore, AWB brazing and hardening technology reduces vibration during drilling to minimise strain on the user. The bit is intended for use on masonry and concrete. To achieve accurate results, the visibility of the wear mark indicates if the diameter of the hole is still in tolerance for metal anchor setting. As proof of quality, the drill …

Faithfull Plug Cutters are used in combination with screwsinks to prepare perfectly sized plugs to fill counterbored holes. For best performance, the power drill should be held in a stand. For a perfect grain match use an offcut from the timber being plugged. To ensure an accurate fit we suggest you use the same screwsink from the Faithfull brand. The set of 4 contains sizes No 6, 8, 10 and 12.Cuts Size 13 mm PlugsAdditional Information:• Plug Type: Plug Cutter• Screw Compatibility (mm): 13

The name of a pro
6 mm diameter drill bit
Compatible with corded and cordless drills
Manufactured from quality steel with a tungsten carbide tip to provide clean, precise drilling in ceramic and glazed tiles, and non-toughened glass

Lasting Performance in Concrete - The CYL-3 Drill Bit provides lasting performance when drilling concrete. Its stamina is a result of a highly durable carbide blend specially developed and manufactured by Bosch. The blend is adapted to meet the demands of repeated use and offers high wear resistance when working with concrete. Moreover, the effective 2-flute U-shape design of the bit provides good dust removal, reducing friction, heat development and wear, resulting in an extended lifetime. The bit delivers lasting performance when drilling holes for fixings in abrasive materials such as concrete and natural stone. It is compatible with cylindrical shank systems for all corded or cordless impact …

Bahco 9629 Series Flat Bit have a positive cutting angle which drills holes twice as fast and lasts 3x longer than a conventional bit. Made from high-carbon steel and heat-treated all over. The hardened blade is forged directly from the round shaft. Its winged shoulders enable the bit to first cut the wood and then remove the material from the centre section, ensuring a smooth finish and superior swarf clearance. 1 x Bahco 9629-38 Flat Bit 38mm

Designed with efficiency in mind, the innovative flute design promotes swift material removal and efficient debris evacuation, reducing the risk of bit binding and ensuring a smooth drilling experience. The robust construction of the bit ensures it can withstand the demands of tough applications, maintaining its sharpness and performance over time. The carbide tip ensures durability and longevity, making it the ideal tool for drilling into concrete, brick, stone, and other masonry materials. Features & Benefits • Flat carbide tip design for less breakage in the hardest of materials • Four flute design removes debris quickly for fast drilling • Hardened steel body for maximum strength …

High quality metal twist drill bits for precise drilling in metal. Made out of high speed steel (HSS). A finely-tuned material elasticity provides for a long service life. Very good concentricity. Tough viscous tempered bits ensure a particularly long service life. The hexagonal shaft ensures very good power transfer. Drive: ¼" hexagon, suitable for holders as per DIN ISO 1173-D 6.3. Features and Benefits: • Twist bit for metal applications • Hex shaft for very good power transfer • HSS = high speed steel with split point • Finely-tuned material elasticity for great durability • Very good concentricity Contents: 848 HSS Metal Twist Drill Bits, 3.1 x 40 mm