Drill Bits

Faithfull Impact Rated Flat Bits are designed to perform fast, clean cuts, will bore all types of timber and are equally efficient when drilling with or against the grain. All bits have a precision ground point and cutting surfaces with extended spurs for faster cutting. All sizes except the 6mm, have a non-slip hexagonal shank with a locking mechanism compatible with adaptors or chucks with a built-in quick-release feature. A 300mm extension shank is available for use with flat bits of 16mm and above, for deep drill applications. Ideal for use with both mains or cordless drills. Made to DIN 3126 quality with 1/4in hexagonal non-slip shaft.Diameter: 38mm.Overall Length: 152mm.Additional Information:• …

The HSS-R construction of this drill bit guarantees exceptional durability and heat resistance, owing to the high-speed steel composition. Rapid chip removal during drilling minimizes heat buildup, extending the drill bit's lifespan. The precision-ground tip enhances cutting efficiency, allowing for smooth and precise drilling in metal surfaces. With a diameter of 11mm and a length of 142mm, this drill bit excels in drilling through various metals, including steel and aluminium. Its design ensures clean and accurate holes, making it an indispensable addition to your toolkit for metal fabrication, construction, and other demanding applications. The 11mm diameter provides the strength and precision …

The SDS plus-3 Drill Bit offers durability when drilling in concrete. To prevent heat development, the 4-flute dura design provides effective dust removal for increased endurance. It is made of high-alloy steel, which is produced with an optimised hardening technology to withstand wear. For additional resistance, indented cutting edges are made from an ideal Bosch-controlled carbide blend. As proof of quality, the drill bit bears the test mark of the PGM Masonry Drill Bit Association Board, guaranteeing compliance with tight tolerances, exact drilling and the firm hold of fixings. The bit is intended for work on concrete and masonry and is to be used with rotary hammers with SDS plus holders.…

Faithfull Cold Chisels are made from high-quality grade steel which is hardened and ground to maximise safety and to ensure longer lasting cutting edges. For cutting brick, concrete and paving slabs. The cutting edge has an angle of approximately 60°. Manufactured to BS 3066.Size: 250 x 25mm (10 x 1 in).Additional Information:• Length: 250mm (10in)• Width: 25mm (1in)

These high-performance Faithfull Tungsten Carbide Tipped Drill Bits fit into SDS Plus chucks which provide a particularly secure non-slip grip that transmits maximum power for rotary percussion drilling, mainly into concrete. The SDS Plus bits ensure maximum power transmission due to their unique fluted shaft. This effectively removes situations where a perfectly serviceable cutting edge is rendered useless by a worn shank. The SDS Plus system also enables faster changing of drills using a quick release keyless chuck. For use in bricks, blocks, concrete containing aggregates, marble and hard stone, and other hard masonry materials.The Faithfull FAISDS13260 SDS Drill has a heavy-duty tungsten …

Faithfull Combination Wood Auger Bits can be used in either a hand or power drill at low speeds. Machined from high quality carbon steel, they feature a pitched screw point for accurate starting with a wide flat spiral for improved stability, straight tracking and fast waste removal. Augers may be used in timber, plywood, MDF and blockwood and can be resharpened using a hand file.Size. 8 mm x 200 mmAdditional Information:• Diameter: 8mm• Overall Length: 200mm• Pack Qty.: 1

• Ideal for general-purpose drilling into most masonry materials. For use in a 1/2" chuck with percussion. • Supplied in a plastic wallet.Ideal for general-purpose drilling into most masonry materials. For use in a 1/2" chuck with percussion. Supplied in a plastic wallet.Technical Specification:Size: ø13 x 600mmDimensions: Length: 12mm x Height: 680mmWeight: 0.306KgWarranty: Consumable

14.0 x 150 x 210mm Drill Bit The Bosch SDS-Plus-3 14.0x150x210mm with entring tip and 4-flute design, Suitable for masonry and concrete. 4-flute design Rienforced core section 2-cutter

The SDS plus-5 Drill Bit allows for effortless drilling. For smooth work, the carbide plate is grooved and bears notches that penetrate material more easily and prevent jamming in concrete. Drill guidance for easy starts without jarring or wandering is provided by the Activeteq centring tip, which keeps the drill in place for a precise hole diameter. Furthermore, AWB brazing and hardening technology reduces vibration during drilling to minimise strain on the user. The bit is intended for use on masonry and concrete. To achieve accurate results, the visibility of the wear mark indicates if the diameter of the hole is still in tolerance for metal anchor setting. As proof of quality, the drill …

Osborn Goldex 81504 series jobber drill bits. High quality HSS fully ground titanium coated drill point for longer life. Suitable for drilling in steel, cast steel (alloyed and non-alloyed), grey cast iron, graphite and malleable cast iron. Features & Benefits • High speed steel TiN coated jobber drills • For drilling in steel, cast steel- alloyed and non-alloyed, stainless steel, titanium and aluminium • Standards DIN 338 • Self centering split point above 1.6mm • Bright finish body for maximum chip clearance Specifications • Size: 1.1mm • Flute Length: 14mm • Quantity: Pack of 10 • Point Angle: 118° • Point Type & Helix Angle: N ~ 30° …

Lasts up to 3x longer than a standard drill bitDrilling through reinforced concrete is a tough job, and it has traditionally taken its toll on drill bits. Regular two-cutter bits get stuck in rebar and they eventually break. The Full Carbide Head on the Expert SDS plus-7X is an advanced 4-cutter design made from a single piece of the toughest metal: It doesn’t jam and presents no weakness on impact.Thanks to Bosch Carbide Technology and the Full Carbide Head, the Expert SDS plus-7X lasts far longer than regular hammer drill bits. It punches through rebar effectively so there is no need to stop, re-target or change bits when you strike steel.For construction professionals drilling concrete an…

Irwin Blue Groove 6X Stubby Wood Bits are ideal for drilling wood and offer 6 times faster drilling penetration than a standard flat bit. Their 'Tri-Flute' design allows for faster chip ejection and their full screw tips ensure ease of use and pull through. The cutting spurs produce clean holes with minimal breakout and the tapered flute reduces binding. The drill bits are also heat treated for extra durability. Stubby drill bits are 10cm (4in) long, making them ideal for drilling through joists or in enclosed areas. Suitable for holes up to 5cm (2in) deep.Specifications:Diameter: 22mm.Working length: 50mm (2in).Overall length: 100mm (4in).Additional Information:• Diameter: 22mm• Overall …

The HSS Twist Drill Bit Ground is for drilling through metal with maximum precision. The bit's exposed 135-degree self-centring split-point tip combines active cutting and perfect centring without wandering, delivering maximum precision. The split-point tip also eliminates any need to pre-punch or pilot drill for up to 10 mm. This precision-ground bit made of HSS (high-speed steel) enables up to 40% faster drilling rate and up to 50% lower feed pressure than standard-ground HSS drill bits with chisel edges. This bit is designed for drilling holes in alloyed and non-alloyed steel, cast steel, cast iron, sintered iron, malleable cast iron, non-ferrous metals and hard plastics. The HSS Twist Drill …

Ideal for clean accurate drilling in metal, laminates, plastics and wood. Straight shank HSS jobber drill bit

• Width: 20mm. • Model No. X2CHTechnical Specification:Length: 400mmWidth: 20mmDimensions: Length: 20mm x Height: 480mmWeight: 0.728KgWarranty: Consumable

This drill bit has a hexagonal shank system and works with all drill drivers with a 13-mm chuck. The Auger Bit is ideal for fast drilling-accuracy when producing through-holes, pre-drilling for rafter nails and drilling deep dowel holes in wood. The heavy-duty self-feeding tip pulls the bit through completely, which allows for quick and effortless precision-drilling. Straight holes and a high chip removal rate and increased speed are made possible by the bit's optimised low-friction flute geometry with a solid centre. Its optimised scoring spur and precision-ground main cutting edge produce accurate holes. It is ideal for use in the ancillary building trades, for carpenters and roofers, and …

Faithfull Tri-Point Speed Auger Bits will drill fast and clean holes in all types of wood. The three spurs and cutting edges create perfectly round holes with less chance of binding in the workpiece. Three flutes offer efficient waste removal making them much faster than traditional bits. A self-feeding screw tip enables accurate centring and pulls the bit through the wood. Precision machined from high quality carbon steel with ground and honed cutting edges. The quick release 1/4in hex shank is impact rated for use in impact drivers as well as all other corded and cordless drills. These stubby drill bits are 102mm (4in) long making them ideal for drilling through joists or in enclosed areas.…

Ideal for clean accurate drilling in metal, laminates, plastics and wood. Straight shank HSS jobber drill bit

The CWC Pilot Pins are compatable with Rotabroach TCT series CWC 35mm cutters from 13mm - 17mm

This drill bit has a hexagonal shank system and works with all drill drivers with a 13-mm chuck. The Auger Bit is ideal for fast drilling-accuracy when producing through-holes, pre-drilling for rafter nails and drilling deep dowel holes in wood. The heavy-duty self-feeding tip pulls the bit through completely, which allows for quick and effortless precision-drilling. Straight holes and a high chip removal rate and increased speed are made possible by the bit's optimised low-friction flute geometry with a solid centre. Its optimised scoring spur and precision-ground main cutting edge produce accurate holes. It is ideal for use in the ancillary building trades, for carpenters and roofers, and …

• Ideal for general-purpose drilling into most masonry materials. For use in a 1/2" chuck with percussion. • Supplied in a plastic wallet.Ideal for general-purpose drilling into most masonry materials. For use in a 1/2" chuck with percussion. Supplied in a plastic wallet.Technical Specification:Size: ø18 x 300mmDimensions: Length: 20mm x Height: 377mmWeight: 0.265KgWarranty: Consumable

Rotabroach RAP120 Pilot Pin For 12mm Cutters Only

Osborn Goldex 81504 series jobber drill bits. High quality HSS fully ground titanium coated drill point for longer life. Suitable for drilling in steel, cast steel (alloyed and non-alloyed), grey cast iron, graphite and malleable cast iron. Features & Benefits • High speed steel TiN coated jobber drills • For drilling in steel, cast steel- alloyed and non-alloyed, stainless steel, titanium and aluminium • Standards DIN 338 • Self centering split point above 1.6mm • Bright finish body for maximum chip clearance Specifications • Size: 1.4mm • Flute Length: 18mm • Quantity: Pack of 10 • Point Angle: 118° • Point Type & Helix Angle: N ~ 30° …

The HSS Twist Drill Bit Titanium offers maximum lifetime while drilling holes in metal. When using the appropriate cooling system, the drill bit has the lowest possible level of friction and minimal wear, due to its titanium-nitride coating. The high surface quality of this ground twist drill bit, which is made from HSS (high-speed steel), allows for extended usage. It is suitable for use on alloyed and non-alloyed steel, malleable cast iron, sintered iron, new silver, copper, bronze and hard plastics such as perspex. The HSS Twist Drill Bit Titanium is manufactured to DIN 338. The drill bit is Type N (flute angle) with a 135-degree tip and a diameter tolerance of h8. Active cutting and perfect …