Drill Bits

The SDS plus-5X Drill Bit offers highly efficient drilling in reinforced concrete. The geometrical form of the 4-cutter head prevents jamming and breakage for optimal results. The “turn-angle” head and the large and short dust removal channels within the 4-flute design provide fast dust removal so the bit can slice through concrete and rebar quickly with reduced wear. For efficient work and exact hole diameters, the centring tip guides drilling from the start, to prevent wandering, which can falsify the hole diameter. The bit is intended for use on masonry, concrete and reinforced concrete. As proof of quality, the drill bit bears the test mark of the PGM Masonry Drill Bit Association Board, gua…

Faithfull Standard masonry bits are for use in chucks up to 13mm capacity and are suitable for general purpose drilling including bricks, blocks and cement render when used in an impact or percussion drill. A roll formed and treated body with a heavy-duty Tungsten Carbide tip and fast spiral for quick waste removal.Manufactured to DIN 8039. Zinc plated finish and packed individually. Size.16 mm x 150 mm.Additional Information:• Diameter: 16.0mm• Overall Length: 150mm• Pack Qty.: 1

Lasts up to 3x longer than a standard drill bitDrilling through reinforced concrete is a tough job, and it has traditionally taken its toll on drill bits. Regular two-cutter bits get stuck in rebar and they eventually break. The Full Carbide Head on the Expert SDS plus-7X is an advanced 4-cutter design made from a single piece of the toughest metal: It doesn’t jam and presents no weakness on impact.Thanks to Bosch Carbide Technology and the Full Carbide Head, the Expert SDS plus-7X lasts far longer than regular hammer drill bits. It punches through rebar effectively so there is no need to stop, re-target or change bits when you strike steel.For construction professionals drilling concrete an…

The HSS Twist Drill Bit Titanium offers maximum lifetime while drilling holes in metal. When using the appropriate cooling system, the drill bit has the lowest possible level of friction and minimal wear, due to its titanium-nitride coating. The high surface quality of this ground twist drill bit, which is made from HSS (high-speed steel), allows for extended usage. It is suitable for use on alloyed and non-alloyed steel, malleable cast iron, sintered iron, new silver, copper, bronze and hard plastics such as perspex. The HSS Twist Drill Bit Titanium is manufactured to DIN 338. The drill bit is Type N (flute angle) with a 135-degree tip and a diameter tolerance of h8. Active cutting and perfect …

The SDS plus-7 Drill Bit performs precision-drilling in reinforced concrete. Its full carbide head with 5 cutters is fused with IDS welding technology to drill with a very high level of accuracy. A vibration-reduced power transfer from the rotary hammer to the full carbide head is provided by the 2 + 2 flute design, which is made of high-alloy steel and created using optimised hardening technology. This offers the stability necessary for exact results. To prevent wandering and obtain a precise hole diameter, the Activeteq centring tip guides the drill position from the start. The bit is intended for use on masonry, concrete and reinforced concrete. To achieve accurate results, the visibility …

Stanley drill bits are designed to resist the impacts and fast drilling on concrete. The flute design removes the debris from the hole contribution for longer drill bit life. The hardened steel construction of the drill bit ensures exceptional strength, allowing it to withstand the toughest drilling applications. Whether you are working on soft or hard surfaces, its reinforced carbide tip provides maximum durability and longevity, ensuring consistent performance throughout projects. Features & Benefits • For drilling into house bricks and masonry • Shank diameter of drill bits 10-13mm is reduced to 9.5mm • Diameters larger than 13mm shank is reduced to 12.7mm • For use with …

Expert Quality, tungsten carbide tipped straight shank drills with milled flute. Suitable for use with power drills. Display packed.

Faithfull Tri-Point Speed Auger Bits will drill fast and clean holes in all types of wood. The three spurs and cutting edges create perfectly round holes with less chance of binding in the workpiece. Three flutes offer efficient waste removal making them much faster than traditional bits. A self-feeding screw tip enables accurate centring and pulls the bit through the wood. Precision machined from high quality carbon steel with ground and honed cutting edges. The quick release 1/4in hex shank is impact rated for use in impact drivers as well as all other corded and cordless drills. These stubby drill bits are 102mm (4in) long making them ideal for drilling through joists or in enclosed areas.…

The SDS plus-5 Drill Bit allows for effortless drilling. For smooth work, the carbide plate is grooved and bears notches that penetrate material more easily and prevent jamming in concrete. Drill guidance for easy starts without jarring or wandering is provided by the Activeteq centring tip, which keeps the drill in place for a precise hole diameter. Furthermore, AWB brazing and hardening technology reduces vibration during drilling to minimise strain on the user. The bit is intended for use on masonry and concrete. To achieve accurate results, the visibility of the wear mark indicates if the diameter of the hole is still in tolerance for metal anchor setting. As proof of quality, the drill …

Expert Quality, metric-sized high speed steel drills (with 5% cobalt). The addition of cobalt to HSS prevents wear for longer life. Display packed.

The Makita Performance SDS Plus range consists of European manufactured hammer drill bits with a patented high volume multi-flute that quickly channels the drilling dust from the hole, saving both time and money. Due to its aggressive design, the fast and durable carbide tip allows easy centering and spot drilling. Designed for regular professional use, providing excellent performance in the toughest of materials. Also excellent for drilling in high resistance materials such as Green Concrete or Engineering Brick. The unique reinforced flute geometry transfers more impact energy from the rotary hammer to the drill head, reducing stress for user and power tool. The design and technology innovations …

Faithfull Standard masonry bits are for use in chucks up to 13mm capacity and are suitable for general purpose drilling including bricks, blocks and cement render when used in an impact or percussion drill. A roll formed and treated body with a heavy-duty Tungsten Carbide tip and fast spiral for quick waste removal.Size.8 mm x 400 mm.Additional Information:• Diameter: 8.0mm• Overall Length: 400mm• Pack Qty.: 1

The HSS Twist Drill Bit Ground is for drilling through metal with maximum precision. The bit's exposed 135-degree self-centring split-point tip combines active cutting and perfect centring without wandering, delivering maximum precision. The split-point tip also eliminates any need to pre-punch or pilot drill for up to 10 mm. This precision-ground bit made of HSS (high-speed steel) enables up to 40% faster drilling rate and up to 50% lower feed pressure than standard-ground HSS drill bits with chisel edges. This bit is designed for drilling holes in alloyed and non-alloyed steel, cast steel, cast iron, sintered iron, malleable cast iron, non-ferrous metals and hard plastics. The HSS Twist Drill …

Faithfull Combination Wood Auger Bits can be used in either a hand or power drill at low speeds. Machined from high quality carbon steel, they feature a pitched screw point for accurate starting with a wide flat spiral for improved stability, straight tracking and fast waste removal. Augers may be used in timber, plywood, MDF and blockwood and can be resharpened using a hand file.

Bahco 9629 Series Flat Bit have a positive cutting angle which drills holes twice as fast and lasts 3x longer than a conventional bit. Made from high-carbon steel and heat-treated all over. The hardened blade is forged directly from the round shaft. Its winged shoulders enable the bit to first cut the wood and then remove the material from the centre section, ensuring a smooth finish and superior swarf clearance. Sizes 10mm and above feature cutting spurs.1 x Bahco 9629-40 Flat Bit 40mmAdditional Information:• Diameter: 40mm• Overall Length: 160mm• Pack Qty.: 1

• Superior quality auger wood drill bit has a hexagonal shank for higher torque ranges demanded by this drill type.• Fully hardened with a screw point to aid location and smooth drilling.• Supplied in a plastic wallet.Superior quality auger wood drill bit has a hexagonal shank for higher torque ranges demanded by this drill type. Fully hardened with a screw point to aid location and smooth drilling. Supplied in a plastic wallet.Technical Specification:Size: ø18 x 460mmDimensions: Length: 5mm x Height: 525mmWeight: 0.406KgWarranty: Consumable

For use with all multi-tooth milling cutters with 6mm bore. Features and Benefits Pilots locate into pre-drilled pilot holes ensuring positional accuracy of the cutter Suitable for 'blind' or 'through' pilot holes, pin will retract into cutter adaptor upon 'bottoming' Notes Short Series = 12mm cutter For 12mm cutters only Long Series = 13 - 52mm cutters

The Dormer A225 HSS Centre Drill is a precision tool designed for creating accurate centre holes in workpieces, essential for facilitating subsequent drilling operations. Made from High-Speed Steel, this centre drill offers exceptional durability and performance, capable of handling various materials including steel, stainless steel, and non-ferrous metals. Its high-quality construction ensures excellent resistance to wear and heat, maintaining sharpness and precision even under demanding conditions. The 60-degree included angle of the centre drill guarantees precise centering and optimal hole preparation, reducing the risk of tool deflection and ensuring accurate alignment for follow-up drilling.…

The Makita Performance SDS Plus range consists of European manufactured hammer drill bits with a patented high volume multi-flute that quickly channels the drilling dust from the hole, saving both time and money. Due to its aggressive design, the fast and durable carbide tip allows easy centering and spot drilling. Designed for regular professional use, providing excellent performance in the toughest of materials. Also excellent for drilling in high resistance materials such as Green Concrete or Engineering Brick. The unique reinforced flute geometry transfers more impact energy from the rotary hammer to the drill head, reducing stress for user and power tool. The design and technology innovations …

Faithfull Standard masonry bits are for use in chucks up to 13mm capacity and are suitable for general purpose drilling including bricks, blocks and cement render when used in an impact or percussion drill. A roll formed and treated body with a heavy-duty Tungsten Carbide tip and fast spiral for quick waste removal.Manufactured to DIN 8039. Zinc plated finish and packed individually. Size.10 mm x 300 mm.Additional Information:• Diameter: 10.0mm• Overall Length: 300mm• Pack Qty.: 1

Expert Quality, flat wood bits with a precision ground central point and enhanced design cutting edge spurs, which deliver greater waste removal compared with standard flat wood bits. Made from high quality carbon steel that's correctly hardened and tempered. Each cutting edge is expertly ground and finished for maximum performance. Ideal for use with combi drills, drill drivers and impact drivers. All sizes have a strong 6mm shank.

Lasts up to 3x longer than a standard drill bitDrilling through reinforced concrete is a tough job, and it has traditionally taken its toll on drill bits. Regular two-cutter bits get stuck in rebar and they eventually break. The Full Carbide Head on the Expert SDS plus-7X is an advanced 4-cutter design made from a single piece of the toughest metal: It doesn’t jam and presents no weakness on impact.Thanks to Bosch Carbide Technology and the Full Carbide Head, the Expert SDS plus-7X lasts far longer than regular hammer drill bits. It punches through rebar effectively so there is no need to stop, re-target or change bits when you strike steel.For construction professionals drilling concrete an…

Up to 3x faster than a standard drill bitSpade bits are a great accessory for electricians and other installation and building workers. What if they could be even faster and more efficient? With Bosch Tip Technology, they can.The Expert SelfCut Speed features the most advanced designs for spade bits, making it easy to use and highly practical for heavy professional users. Its Bosch patent threaded tip draws the spade bit into wood with only the lightest pressure from the user, which is especially helpful when drilling upside down or in tight niches. Its advanced paddle design ensures extra speed.Equally at home in softwoods, chipboard or particleboard, the Bosch Expert SelfCut Speed Spade Bit …

Bosch 2608833800 SDS Plus-5X Hammer Drill Bit 10mm x 200mm x 260mm The Bosch 2608833800 SDS Plus bits offer highly efficient drilling in reinforced concrete and masonry. They have a 4-flute design which provides fast dust removal so the bit can slice through concrete and rebar quickly with reduced wear. The centring tip prevents wandering and geometrical form prevents jamming. Features:
- SDS plus-5X Drill Bit offers highly efficient drilling in reinforced concrete
- Geometrical form of the 4-cutter head prevents jamming and breakage for optimal results
- “Turn-angle” head and 4-flute design provide fast dust removal for increased drilling speeds and reduced wear
- Centring tip guid…