Drill Bits

The Faithfull Bevel Edged Chisel range are quality tools for professional work as well as DIY users. The blue PVC handles on these chisels are impact resistant and designed for use with a mallet or an occasional hammer blow. Each blade is manufactured from drop-forged chrome vanadium steel that is hardened and tempered to exacting standards, ensuring that the cutting edge remains sharper for longer. The bevelled edges make these chisels ideal for fine work and for cutting into tight corners. All the chisels in this range are supplied with blade guards.The Faithfull FAIWCB38 bevel edged chisel is blue and has the following dimensions:Blade Width: 10mm (3/8in)Blade Length: 140mmAdditional Information:• …

Faithfull Tri-Point Speed Auger Bits will drill fast and clean holes in all types of wood. The three spurs and cutting edges create perfectly round holes with less chance of binding in the workpiece. Three flutes offer efficient waste removal making them much faster than traditional bits. A self-feeding screw tip enables accurate centring and pulls the bit through the wood. Precision machined from high-quality carbon steel with ground and honed cutting edges. The quick-release 1/4in hex shank is impact rated for use in impact drivers as well as all other corded and cordless drills. Specification: Overall Length: 159mm1 x Faithfull Tri-Point Speed Auger Bit 16mmAdditional Information:• Diameter: …

The RAPL120 series pilot pins are compatible with rotabroach 12mm M2 RAPL 50mm depth of cut rotabroach cutters only.

These Faithfull SDS Plus Chisel Bits are made from drop-forged chrome molybdenum with a heat-treated tempered edge. Molybdenum is ideally suited for chisels because of its known reputation for hardness, toughness and wear resistance. Used mainly for light demolition, chiselling, stripping plaster, mortar chasing, channelling and breaking through brickwork.1 x Faithfull SDS Plus Chisel Bit Angled 40mm Length 250mmAdditional Information:• Type: Angled• Size: 40 x 250mm

The HSS Twist Drill Bit Ground is for drilling through metal with maximum precision. The bit's exposed 135-degree self-centring split-point tip combines active cutting and perfect centring without wandering, delivering maximum precision. The split-point tip also eliminates any need to pre-punch or pilot drill for up to 10 mm. This precision-ground bit made of HSS (high-speed steel) enables up to 40% faster drilling rate and up to 50% lower feed pressure than standard-ground HSS drill bits with chisel edges. This bit is designed for drilling holes in alloyed and non-alloyed steel, cast steel, cast iron, sintered iron, malleable cast iron, non-ferrous metals and hard plastics. The HSS Twist Drill …

The HSS-R construction of this drill bit guarantees exceptional durability and heat resistance, owing to the high-speed steel composition. Rapid chip removal during drilling minimizes heat buildup, extending the drill bit's lifespan. The precision-ground tip enhances cutting efficiency, allowing for smooth and precise drilling in metal surfaces. With a diameter of 11mm and a length of 142mm, this drill bit excels in drilling through various metals, including steel and aluminium. Its design ensures clean and accurate holes, making it an indispensable addition to your toolkit for metal fabrication, construction, and other demanding applications. The 11mm diameter provides the strength and precision …

The Faithfull Professional Pre Pack Metric HSS Jobber Drill Bits are designed to meet the requirements of the professional user, these pre-packed drills are manufactured from M2 grade steel and are fully ground to meet the standard of DIN 338 and feature a 135° non-slip split point. Suitable for use in: Alloy steels, carbon steels, cast iron, hardened alloy steels and stainless steels.Diameter: 9.0mmAdditional Information:• Tip Diameter: 9.0mm• Working Length: 76mm• Overall Length: 125mm• Pack Qty.: 1

Up to 5x more precise than a standard drill bitThe modern construction site requires working on many different materials, and you never know what you will need to drill next. Finding the right drill bit can be difficult and time-consuming – unless you have the Expert MultiConstruction Drill Bit.This highly versatile drill bit can drill accurately into hard materials such as tile and granite without skidding, thanks to its sharp tip and advanced geometric design. Made from optimised carbide using our fine grinding manufacturing technique, it can also tackle concrete, brick, wood and metal. It can always do a professional job – whatever the material.The Bosch Expert CYL-9 MultiConstruction Cyli…

The HSS Twist Drill Bit Ground is for drilling through metal with maximum precision. The bit's exposed 135-degree self-centring split-point tip combines active cutting and perfect centring without wandering, delivering maximum precision. The split-point tip also eliminates any need to pre-punch or pilot drill for up to 10 mm. This precision-ground bit made of HSS (high-speed steel) enables up to 40% faster drilling rate and up to 50% lower feed pressure than standard-ground HSS drill bits with chisel edges. This bit is designed for drilling holes in alloyed and non-alloyed steel, cast steel, cast iron, sintered iron, malleable cast iron, non-ferrous metals and hard plastics. The HSS Twist Drill …

The HEX-9 Ceramic Tile Drill Bit performs fast drilling in tiles. High-speed drilling is made possible by the 7-sided asymmetrical diamond-ground cutting edges, which efficiently slice through materials. The 2-flute U-shape design provides effective dust removal, which allows the drill to glide through the material quickly for fast results. This drill bit is intended for work in soft-to-medium density tiles, porcelain and ceramic. Only use this drill bit at low speeds and without the impact and hammer function. No cooling is required. It is compatible with impact drivers due to its hex-shank and it is suitable for use with standard drivers with chucks. Pack of 1 • Fast Drilling in Tiles …

This spade bit has a 1/4-inch hex shank system and it is best for use with portable power drills. The Self-Cut Speed Spade Bit performs extremely fast hole drilling. Its self-feeding threaded tip enables the drill bit to effortlessly pull itself into the wood for high-speed drilling with little exertion. Fast chip removal for rapid results is made possible by the specially shaped spade. In product tests, this drill bit produces holes 10 times faster than a standard spade bit. It is suitable for use on soft and hard wood, light building materials and plasterboard. Total length 152 mm • Extremely Fast Holes • Self-Cut Speed Spade Bit performs extremely fast hole drilling • Self-feeding …

Bahco 9629 Series Flat Bit have a positive cutting angle which drills holes twice as fast and lasts 3x longer than a conventional bit. Made from high-carbon steel and heat-treated all over. The hardened blade is forged directly from the round shaft. Its winged shoulders enable the bit to first cut the wood and then remove the material from the centre section, ensuring a smooth finish and superior swarf clearance. Sizes 10mm and above feature cutting spurs.1 x Bahco 9629-38 Flat Bit 38mmAdditional Information:• Diameter: 38mm• Overall Length: 160mm• Pack Qty.: 1

Lasts up to 3x longer than a standard drill bitDrilling through reinforced concrete is a tough job, and it has traditionally taken its toll on drill bits. Regular two-cutter bits get stuck in rebar and they eventually break. The Full Carbide Head on the Expert SDS plus-7X is an advanced 4-cutter design made from a single piece of the toughest metal: It doesn’t jam and presents no weakness on impact.Thanks to Bosch Carbide Technology and the Full Carbide Head, the Expert SDS plus-7X lasts far longer than regular hammer drill bits. It punches through rebar effectively so there is no need to stop, re-target or change bits when you strike steel.For construction professionals drilling concrete an…

Osborn Goldex 81504 series jobber drill bits.High Quaility HSS fully ground Titanium Coated Drill point for longer life. Suitable for drilling in steel, cast steel (alloyed and non alloyed), grey cast iron, graphite and malleable cast iron. Specifications • Standards: DIN 338 • Composition: High Speed Steel • Point Angle: 118° • Point Type & Helix Angle: N ~ 30° • Drill Body Tolerance: h8

Faithfull Combination Wood Auger Bits can be used in either a hand or power drill at low speeds. Machined from high quality carbon steel, they feature a pitched screw point for accurate starting with a wide flat spiral for improved stability, straight tracking and fast waste removal. Augers may be used in timber, plywood, MDF and blockwood and can be resharpened using a hand file.Size. 8 mm x 200 mmAdditional Information:• Diameter: 8mm• Overall Length: 200mm• Pack Qty.: 1

HSS Twist Drill Bit PointTeQ enables fast drilling in metal due to PointTeQ tip design Self-centering tip prevents wandering, making quick and easy drilling starts possible Increased drilling rate generates less heat and wear PointTeQ tip design remains sharp and ensures continuous durability The HSS Twist Drill Bit PointTeQ enables fast drilling in metal due to its PointTeQ tip design. Quick and easy drilling starts are possible as the self-centering tip prevents wandering. Because of its increased drilling rate, less heat and wear are generated. The PointTeQ tip design remains sharp and ensures continuous durability. This bit is suitable for drilling clearance and pilot holes in alloyed and …

These Faithfull chisels are suited to cutting bricks during building work. This chisel has a suitably hardened cutting edge, but should not be used on concrete containing reinforcing bars.Size: 75 x 225mm (3in x 9in).Additional Information:• Width: 75mm

The HEX-9 Ceramic Tile Drill Bit performs fast drilling in tiles. High-speed drilling is made possible by the 7-sided asymmetrical diamond-ground cutting edges, which efficiently slice through materials. The 2-flute U-shape design provides effective dust removal, which allows the drill to glide through the material quickly for fast results. This drill bit is intended for work in soft-to-medium density tiles, porcelain and ceramic. Only use this drill bit at low speeds and without the impact and hammer function. No cooling is required. It is compatible with impact drivers due to its hex-shank and it is suitable for use with standard drivers with chucks. Pack of 1 • Fast Drilling in Tiles …

Faithfull Multi Construction Drill Bits are suitable for use in most materials encountered in the building industry. They can be used on brick, tile, concrete, metal, aluminium, wood and plastic, and are ideal for multi-layer materials. The diamond-ground carbide tip has advanced performance cutting edges for a long working life and the flute is designed for fast debris removal. Perfect for use in cordless drills when used on both rotary or hammer modes, dependent on the material being drilled (4mm bit rotary only).1 x Faithfull Multi Construction Drill Bit 12 x 150mmAdditional Information:• Tip Diameter: Working Length• Overall Length: Pack Qty.• 150mm: 1

Ideal for clean accurate drilling in metal, laminates, plastics and wood. Straight shank HSS jobber drill bit

• Ideal for general-purpose drilling into most masonry materials. For use in a 1/2" chuck with percussion. • Supplied in a plastic wallet.Ideal for general-purpose drilling into most masonry materials. For use in a 1/2" chuck with percussion. Supplied in a plastic wallet.Technical Specification:Size: ø18 x 300mmDimensions: Length: 20mm x Height: 377mmWeight: 0.265KgWarranty: Consumable

Lasts up to 3x longer than a standard drill bitDrilling through reinforced concrete is a tough job, and it has traditionally taken its toll on drill bits. Regular two-cutter bits get stuck in rebar and they eventually break. The Full Carbide Head on the Expert SDS plus-7X is an advanced 4-cutter design made from a single piece of the toughest metal: It doesn’t jam and presents no weakness on impact.Thanks to Bosch Carbide Technology and the Full Carbide Head, the Expert SDS plus-7X lasts far longer than regular hammer drill bits. It punches through rebar effectively so there is no need to stop, re-target or change bits when you strike steel.For construction professionals drilling concrete an…

The solid carbide construction ensures exceptional hardness and wear resistance, making it perfect for drilling through tough materials like stainless steel, cast iron, and hardened metals. The TiN (Titanium Nitride) tip coating enhances the drill's cutting efficiency and longevity by reducing friction and heat buildup. This allows for faster drilling speeds and extended tool life. Designed with a jobber length, the Dormer R003 offers optimal balance between rigidity and reach, ensuring accurate and clean holes every time. Features & Benefits • Bright and TiN tip coating • Hard material solid carbide • 120° drill point • Cylindrical shank/straight shank • Standard …

Lasts up to 3x longer than a standard drill bitDrilling through reinforced concrete is a tough job, and it has traditionally taken its toll on drill bits. Regular two-cutter bits get stuck in rebar and they eventually break. The Full Carbide Head on the Expert SDS plus-7X is an advanced 4-cutter design made from a single piece of the toughest metal: It doesn’t jam and presents no weakness on impact.Thanks to Bosch Carbide Technology and the Full Carbide Head, the Expert SDS plus-7X lasts far longer than regular hammer drill bits. It punches through rebar effectively so there is no need to stop, re-target or change bits when you strike steel.For construction professionals drilling concrete an…