Drill Bits

Faithfull Cold Chisels are made from high-quality grade steel which is hardened and ground to maximise safety and to ensure longer lasting cutting edges. For cutting brick, concrete and paving slabs. The cutting edge has an angle of approximately 60. Manufactured to BS 3066.

Lasts up to 3x longer than a standard drill bitDrilling through reinforced concrete is a tough job, and it has traditionally taken its toll on drill bits. Regular two-cutter bits get stuck in rebar and they eventually break. The Full Carbide Head on the Expert SDS plus-7X is an advanced 4-cutter design made from a single piece of the toughest metal: It doesn’t jam and presents no weakness on impact.Thanks to Bosch Carbide Technology and the Full Carbide Head, the Expert SDS plus-7X lasts far longer than regular hammer drill bits. It punches through rebar effectively so there is no need to stop, re-target or change bits when you strike steel.For construction professionals drilling concrete an…

An economical bit for cutting quick holes in timber. With centre point, back tapered cutting edge and ground chip breakers. Specifications: • Shank Diameter: 1/4 hex • Dia Metric: 12 • Overall Length Metric: 152

Faithfull Combination Wood Auger Bits can be used in either a hand or power drill at low speeds. Machined from high quality carbon steel, they feature a pitched screw point for accurate starting with a wide flat spiral for improved stability, straight tracking and fast waste removal. Augers may be used in timber, plywood, MDF and blockwood and can be resharpened using a hand file.

The SDS plus-3 Drill Bit offers durability when drilling in concrete. To prevent heat development, the 4-flute dura design provides effective dust removal for increased endurance. It is made of high-alloy steel, which is produced with an optimised hardening technology to withstand wear. For additional resistance, indented cutting edges are made from an ideal Bosch-controlled carbide blend. As proof of quality, the drill bit bears the test mark of the PGM Masonry Drill Bit Association Board, guaranteeing compliance with tight tolerances, exact drilling and the firm hold of fixings. The bit is intended for work on concrete and masonry and is to be used with rotary hammers with SDS plus holders.…

Expert Quality, tungsten carbide tipped straight shank drills with milled flute. Suitable for use with power drills. Display packed.

Osborn Goldex 81504 series jobber drill bits.High Quaility HSS fully ground Titanium Coated Drill point for longer life. Suitable for drilling in steel, cast steel (alloyed and non alloyed), grey cast iron, graphite and malleable cast iron. Specifications • Standards: DIN 338 • Composition: High Speed Steel • Point Angle: 118° • Point Type & Helix Angle: N ~ 30° • Drill Body Tolerance: h8

The Irwin masonry drills bits are designed for fast and efficient drilling in brickwork, concrete and breeze block, especially with cordless drills. They drill up to 60% faster than competitive drill bits whilst maintaining the same high durability. The single flute design ensures faster dust removal for increased drilling speed, with the unique, pressed diamond-ground carbide tip allows for aggressive cutting and the carbide tip design also ensures 20% longer life compared to previous Irwin masonry drill bits. The bits are made with a chrome vanadium body with high carbon content which allows more hardening and a stronger bit for maximum rupture strength.

Faithfull Impact Rated Flat Bits are designed to perform fast, clean cuts, will bore all types of timber and are equally efficient when drilling with or against the grain. All bits have a precision ground point and cutting surfaces with extended spurs for faster cutting. All sizes except the 6mm, have a non-slip hexagonal shank with a locking mechanism compatible with adaptors or chucks with a built-in quick-release feature. A 300mm extension shank is available for use with flat bits of 16mm and above, for deep drill applications. Ideal for use with both mains or cordless drills. Made to DIN 3126 quality with 1/4in hexagonal non-slip shaft.

• Width: 20mm. • Model No. X1CHTechnical Specification:Length: 300mmWidth: 20mmWeight: 2KgWarranty: Consumable

Drilling into reinforced concrete is no longer a hit and miss application, reinforcing bar being no obstacle for the nemesis drill. Also perfect for use in the hardest of natural stone. Its unique symmetrical head geometry ensures precision drill holes. Perfect for critical anchor fixings and where spot drilling is required. Features & Benefits:• Symmetrical head-geometry with centring-tip for optimised results in the event of reinforcement• The nemesis will drill up to 50% more holes than the normal rotary hammer drill bits.Specifications:Diameter (D) - 12 mmOverall Length - 160 mmShank - SDS-PLUS Working Length - 100 mmPack Quantity - 1

The HSS Twist Drill Bit Titanium offers maximum lifetime while drilling holes in metal. When using the appropriate cooling system, the drill bit has the lowest possible level of friction and minimal wear, due to its titanium-nitride coating. The high surface quality of this ground twist drill bit, which is made from HSS (high-speed steel), allows for extended usage. It is suitable for use on alloyed and non-alloyed steel, malleable cast iron, sintered iron, new silver, copper, bronze and hard plastics such as perspex. The HSS Twist Drill Bit Titanium is manufactured to DIN 338. The drill bit is Type N (flute angle) with a 135-degree tip and a diameter tolerance of h8. Active cutting and perfect …

Lasts up to 3x longer than a standard drill bitDrilling through reinforced concrete is a tough job, and it has traditionally taken its toll on drill bits. Regular two-cutter bits get stuck in rebar and they eventually break. The Full Carbide Head on the Expert SDS plus-7X is an advanced 4-cutter design made from a single piece of the toughest metal: It doesn’t jam and presents no weakness on impact.Thanks to Bosch Carbide Technology and the Full Carbide Head, the Expert SDS plus-7X lasts far longer than regular hammer drill bits. It punches through rebar effectively so there is no need to stop, re-target or change bits when you strike steel.For construction professionals drilling concrete an…

Ideal for clean accurate drilling in metal, laminates, plastics and wood. Straight shank HSS jobber drill bit

The CWCL TCT series Pilot Pins are compatible with Rotabroach TCT cutters from 66mm to 100mm diameter and 50mm depth of cut.

The HSS Twist Drill Bit Ground is for drilling through metal with maximum precision. The bit's exposed 135-degree self-centring split-point tip combines active cutting and perfect centring without wandering, delivering maximum precision. The split-point tip also eliminates any need to pre-punch or pilot drill for up to 10 mm. This precision-ground bit made of HSS (high-speed steel) enables up to 40% faster drilling rate and up to 50% lower feed pressure than standard-ground HSS drill bits with chisel edges. This bit is designed for drilling holes in alloyed and non-alloyed steel, cast steel, cast iron, sintered iron, malleable cast iron, non-ferrous metals and hard plastics. The HSS Twist Drill …

High quality metal twist drill bits for precise drilling in metal. Made out of high speed steel (HSS). A finely-tuned material elasticity provides for a long service life. Very good concentricity. Tough viscous tempered bits ensure a particularly long service life. The hexagonal shaft ensures very good power transfer. Drive: ¼" hexagon, suitable for holders as per DIN ISO 1173-D 6.3. Features and Benefits: • Twist bit for metal applications • Hex shaft for very good power transfer • HSS = high speed steel with split point • Finely-tuned material elasticity for great durability • Very good concentricity Contents: 848 HSS Metal Twist Drill Bits, 4.1 x 44 mm

High quality metal twist drill bits for precise drilling in metal. Made out of high speed steel (HSS). A finely-tuned material elasticity provides for a long service life. Very good concentricity. Tough viscous tempered bits ensure a particularly long service life. The hexagonal shaft ensures very good power transfer. Drive: ¼" hexagon, suitable for holders as per DIN ISO 1173-D 6.3. Features and Benefits: • Twist bit for metal applications • Hex shaft for very good power transfer • HSS = high speed steel with split point • Finely-tuned material elasticity for great durability • Very good concentricity Contents: 848 HSS Metal Twist Drill Bits, 5 x 50 mm

The Irwin IRW10502187 Speedhammer Max flat chisel has the following dimensions:Size: 25 x 280mm

This spade bit has a 1/4-inch hex shank system and it is best for use with portable power drills. The Self-Cut Speed Spade Bit performs extremely fast hole drilling. Its self-feeding threaded tip enables the drill bit to effortlessly pull itself into the wood for high-speed drilling with little exertion. Fast chip removal for rapid results is made possible by the specially shaped spade. In product tests, this drill bit produces holes 10 times faster than a standard spade bit. It is suitable for use on soft and hard wood, light building materials and plasterboard. Total length 152 mm • Extremely Fast Holes • Self-Cut Speed Spade Bit performs extremely fast hole drilling • Self-feeding …

Milwaukee HSS-G Thunderweb Drill Bit design is characterised by a conical shaped web which gets thicker towards the back of the drill bit. Standard drill bits have a constant thickness throughout their length. Even at the narrowest point the Tunderweb core is thicker than that of a standard drill bit. Specifications • Cutting Width: 2.3mm • Length: 53mm • Pack Quantity: 10Features & Benefits• Parabolic web cross section: Large web thickness and strength built in • Thunderweb flute form ejects hot chips rapidly • Dissipates heat better increasing life time • Precision starting, drill bit won't walk on material surface • Polished finish reduces friction …

The Blue Spot Tools 4-22mm Step Drill is specially designed for precision drilling of holes in aluminium, brass, copper, plastic, steel and wood. Manufactured from high steel for increased durability and cutting power. Titanium coated to reduce friction and heat. 2mm step increments. Additional Information:• Size Range: 4-22mm• No. of Steps: 10

Irwin Blue Groove 6X Stubby Wood Bits are ideal for drilling wood and offer 6 times faster drilling penetration than a standard flat bit. Their 'Tri-Flute' design allows for faster chip ejection and their full screw tips ensure ease of use and pull through. The cutting spurs produce clean holes with minimal breakout and the tapered flute reduces binding. The drill bits are also heat treated for extra durability. Stubby drill bits are 10cm (4in) long, making them ideal for drilling through joists or in enclosed areas. Suitable for holes up to 5cm (2in) deep.Specifications:Diameter: 22mm.Working length: 50mm (2in).Overall length: 100mm (4in).Additional Information:• Diameter: 22mm• Overall …

The CYL-5 Drill Bit guarantees extra-long durability when drilling concrete and stone. The combination of a carbide blend developed in-house by Bosch and diamond-ground cutting edges makes the bit extremely wear-resistant. Friction on the flute from drilled material is notably reduced thanks to a 2-flute vario design with a short, variable incline providing good dust removal and wear reduction. The Bosch Power Grip Shank System enables 100% power transfer from machine to drill bit. This allows a direct use of power for drilling with no power loss and thus less wear. For use when drilling holes for fixings in concrete, natural and artificial stone. As proof of quality, the drill bit bears the …