Drill Bits

The HSS Twist Drill Bit Titanium offers maximum lifetime while drilling holes in metal. When using the appropriate cooling system, the drill bit has the lowest possible level of friction and minimal wear, due to its titanium-nitride coating. The high surface quality of this ground twist drill bit, which is made from HSS (high-speed steel), allows for extended usage. It is suitable for use on alloyed and non-alloyed steel, malleable cast iron, sintered iron, new silver, copper, bronze and hard plastics such as perspex. The HSS Twist Drill Bit Titanium is manufactured to DIN 338. The drill bit is Type N (flute angle) with a 135-degree tip and a diameter tolerance of h8. Active cutting and perfect …

For use with all multi-tooth milling cutters with 6mm bore. Features and Benefits Pilots locate into pre-drilled pilot holes ensuring positional accuracy of the cutter Suitable for 'blind' or 'through' pilot holes, pin will retract into cutter adaptor upon 'bottoming' Notes Short Series = 12mm cutter For 12mm cutters only Long Series = 13 - 52mm cutters

Ideal for clean accurate drilling in metal, laminates, plastics and wood. Straight shank HSS jobber drill bit

This drill bit has a hexagonal shank system and works with all drill drivers with a 13-mm chuck. The Auger Bit is ideal for fast drilling-accuracy when producing through-holes, pre-drilling for rafter nails and drilling deep dowel holes in wood. The heavy-duty self-feeding tip pulls the bit through completely, which allows for quick and effortless precision-drilling. Straight holes and a high chip removal rate and increased speed are made possible by the bit's optimised low-friction flute geometry with a solid centre. Its optimised scoring spur and precision-ground main cutting edge produce accurate holes. It is ideal for use in the ancillary building trades, for carpenters and roofers, and …

Lasts up to 3x longer than a standard drill bitDrilling through reinforced concrete is a tough job, and it has traditionally taken its toll on drill bits. Regular two-cutter bits get stuck in rebar and they eventually break. The Full Carbide Head on the Expert SDS plus-7X is an advanced 4-cutter design made from a single piece of the toughest metal: It doesn’t jam and presents no weakness on impact.Thanks to Bosch Carbide Technology and the Full Carbide Head, the Expert SDS plus-7X lasts far longer than regular hammer drill bits. It punches through rebar effectively so there is no need to stop, re-target or change bits when you strike steel.For construction professionals drilling concrete an…

High quality metal twist drill bits for precise drilling in metal. Made out of high speed steel (HSS). A finely-tuned material elasticity provides for a long service life. Very good concentricity. Tough viscous tempered bits ensure a particularly long service life. The hexagonal shaft ensures very good power transfer. Drive: ¼" hexagon, suitable for holders as per DIN ISO 1173-D 6.3. Features and Benefits: • Twist bit for metal applications • Hex shaft for very good power transfer • HSS = high speed steel with split point • Finely-tuned material elasticity for great durability • Very good concentricity Contents: 848 HSS Metal Twist Drill Bits, 5.1 x 50 mm

The SDS plus-3 Drill Bit offers durability when drilling in concrete. To prevent heat development, the 4-flute dura design provides effective dust removal for increased endurance. It is made of high-alloy steel, which is produced with an optimised hardening technology to withstand wear. For additional resistance, indented cutting edges are made from an ideal Bosch-controlled carbide blend. As proof of quality, the drill bit bears the test mark of the PGM Masonry Drill Bit Association Board, guaranteeing compliance with tight tolerances, exact drilling and the firm hold of fixings. The bit is intended for work on concrete and masonry and is to be used with rotary hammers with SDS plus holders.…

Expert Quality, tungsten carbide tipped straight shank drills with milled flute. Suitable for use with power drills. Display packed.

Milwaukee SDS Plus 2-Cut drill bits have 3 offset aggressive power breakers. These produce a demolition effect and create micro cracks in the drilled material. Centering tip ensures immediate spot drilling with pin point accuracy and prevents skidding on smooth surfaces. Enlarged rebar chamfers prevent side tip damage when hitting rebar, this reduces the risk of the drill bit jamming when hitting rebar. Tapered shoulder design provides a thinner shoulder towards drill tip for less friction providing for greater speed. This is Ideal for cordless hammers identified from its tapered shoulder geometry. Reinforced flute has high volume flute geometry for optimum dust removal. Reinforced flute design …

Bahco 9629 Series Flat Bit have a positive cutting angle which drills holes twice as fast and lasts 3x longer than a conventional bit. Made from high-carbon steel and heat-treated all over. The hardened blade is forged directly from the round shaft. Its winged shoulders enable the bit to first cut the wood and then remove the material from the centre section, ensuring a smooth finish and superior swarf clearance. 1 x Bahco 9629-40 Flat Bit 40mm

A must for every Engineers toolbox! StepPower is the perfect tool for precise drilling with a cordless screwdriver or handheld drill without punching or pre-drilling. The innovative step geometry ensures that the material is gradually removed until the desired diameter is achieved. This makes for effortless drilling without exerting force and saves battery power. The stepped twist drill allows the drilling of virtually burr-free holes in all common materials such as hardwood, plastic or metal. The tool also easily drills composite materials. Suited for cordless drills.This makes StepPower an indispensable all-rounder for every workshop. Features & Benefits • 118° Point geometry with …

Bahco 9629 Series Flat Bit have a positive cutting angle which drills holes twice as fast and lasts 3x longer than a conventional bit. Made from high-carbon steel and heat-treated all over. The hardened blade is forged directly from the round shaft. Its winged shoulders enable the bit to first cut the wood and then remove the material from the centre section, ensuring a smooth finish and superior swarf clearance. 1 x Bahco 9629-38 Flat Bit 38mm

The HSS Twist Drill Bit Titanium offers maximum lifetime while drilling holes in metal. When using the appropriate cooling system, the drill bit has the lowest possible level of friction and minimal wear, due to its titanium-nitride coating. The high surface quality of this ground twist drill bit, which is made from HSS (high-speed steel), allows for extended usage. It is suitable for use on alloyed and non-alloyed steel, malleable cast iron, sintered iron, new silver, copper, bronze and hard plastics such as perspex. The HSS Twist Drill Bit Titanium is manufactured to DIN 338. The drill bit is Type N (flute angle) with a 135-degree tip and a diameter tolerance of h8. Active cutting and perfect …

Osborn Goldex 81504 series jobber drill bits.High Quaility HSS fully ground Titanium Coated Drill point for longer life. Suitable for drilling in steel, cast steel (alloyed and non alloyed), grey cast iron, graphite and malleable cast iron. Specifications • Standards: DIN 338 • Composition: High Speed Steel • Point Angle: 118° • Point Type & Helix Angle: N ~ 30° • Drill Body Tolerance: h8

Expert Quality, tungsten carbide tipped straight shank drills with milled flute. Suitable for use with power drills. Display packed.

Faithfull Standard masonry bits are for use in chucks up to 13mm capacity and are suitable for general purpose drilling including bricks, blocks and cement render when used in an impact or percussion drill. A roll formed and treated body with a heavy-duty Tungsten Carbide tip and fast spiral for quick waste removal.Size.8 mm x 400 mm.Additional Information:• Diameter: 8.0mm• Overall Length: 400mm• Pack Qty.: 1

The Dormer A225 HSS Centre Drill is a precision tool designed for creating accurate centre holes in workpieces, essential for facilitating subsequent drilling operations. Made from High-Speed Steel, this centre drill offers exceptional durability and performance, capable of handling various materials including steel, stainless steel, and non-ferrous metals. Its high-quality construction ensures excellent resistance to wear and heat, maintaining sharpness and precision even under demanding conditions. The 60-degree included angle of the centre drill guarantees precise centering and optimal hole preparation, reducing the risk of tool deflection and ensuring accurate alignment for follow-up drilling.…

The HSS Twist Drill Bit Ground is for drilling through metal with maximum precision. The bit's exposed 135-degree self-centring split-point tip combines active cutting and perfect centring without wandering, delivering maximum precision. The split-point tip also eliminates any need to pre-punch or pilot drill for up to 10 mm. This precision-ground bit made of HSS (high-speed steel) enables up to 40% faster drilling rate and up to 50% lower feed pressure than standard-ground HSS drill bits with chisel edges. This bit is designed for drilling holes in alloyed and non-alloyed steel, cast steel, cast iron, sintered iron, malleable cast iron, non-ferrous metals and hard plastics. The HSS Twist Drill …

Ideal for clean accurate drilling in metal, laminates, plastics and wood. Straight shank HSS jobber drill bit

The Faithfull Bevel Edged Chisel range are quality tools for professional work as well as DIY users. The blue PVC handles on these chisels are impact resistant and designed for use with a mallet or an occasional hammer blow. Each blade is manufactured from drop-forged chrome vanadium steel that is hardened and tempered to exacting standards, ensuring that the cutting edge remains sharper for longer. The bevelled edges make these chisels ideal for fine work and for cutting into tight corners. All the chisels in this range are supplied with blade guards.

Lasts up to 3x longer than a standard drill bitDrilling through reinforced concrete is a tough job, and it has traditionally taken its toll on drill bits. Regular two-cutter bits get stuck in rebar and they eventually break. The Full Carbide Head on the Expert SDS plus-7X is an advanced 4-cutter design made from a single piece of the toughest metal: It doesn’t jam and presents no weakness on impact.Thanks to Bosch Carbide Technology and the Full Carbide Head, the Expert SDS plus-7X lasts far longer than regular hammer drill bits. It punches through rebar effectively so there is no need to stop, re-target or change bits when you strike steel.For construction professionals drilling concrete an…

The CYL-5 Drill Bit guarantees extra-long durability when drilling concrete and stone. The combination of a carbide blend developed in-house by Bosch and diamond-ground cutting edges makes the bit extremely wear-resistant. Friction on the flute from drilled material is notably reduced thanks to a 2-flute vario design with a short, variable incline providing good dust removal and wear reduction. The Bosch Power Grip Shank System enables 100% power transfer from machine to drill bit. This allows a direct use of power for drilling with no power loss and thus less wear. For use when drilling holes for fixings in concrete, natural and artificial stone. As proof of quality, the drill bit bears the …

Full length bevel edged blades manufactured from carbon steel hardened, tempered, finely ground and clear lacquer coated for corrosion protection. Impact - resistant polypropylene handles. All blades have blade guards. Display packed.

Faithfull Standard masonry bits are for use in chucks up to 13mm capacity and are suitable for general purpose drilling including bricks, blocks and cement render when used in an impact or percussion drill. A roll formed and treated body with a heavy-duty Tungsten Carbide tip and fast spiral for quick waste removal.Manufactured to DIN 8039. Zinc plated finish and packed individually. Size.10 mm x 300 mm.Additional Information:• Diameter: 10.0mm• Overall Length: 300mm• Pack Qty.: 1