Drill Bits

The SDS plus-5X Drill Bit offers highly efficient drilling in reinforced concrete. The geometrical form of the 4-cutter head prevents jamming and breakage for optimal results. The “turn-angle” head and the large and short dust removal channels within the 4-flute design provide fast dust removal so the bit can slice through concrete and rebar quickly with reduced wear. For efficient work and exact hole diameters, the centring tip guides drilling from the start, to prevent wandering, which can falsify the hole diameter. The bit is intended for use on masonry, concrete and reinforced concrete. As proof of quality, the drill bit bears the test mark of the PGM Masonry Drill Bit Association Board, gua…

The Faithfull Professional Long Series HSS Jobber Drill Bits have a longer length for deeper drilling requirements. Designed to meet the requirement of the professional user, these drills are manufactured from M2 grade steel and are fully ground to meet the requirements of DIN 338 and feature a 135 degree non slip split point. Their robust design gives less breakage, easier hole start and improved penetration. Suitable for use in: Alloy Steels, Carbon Steels, Cast Iron, Hardened Alloy Steels, Stainless Steels.The Faithfull FAIPP420LS Pre Pack HSS Jobber Drills(2) Long Series 4.20mm have the following specifications:Diameter: 4.2mm Overall Length: 119mmAdditional Information:• Tip Diameter: …

Lasts up to 3x longer than a standard drill bitDrilling through reinforced concrete is a tough job, and it has traditionally taken its toll on drill bits. Regular two-cutter bits get stuck in rebar and they eventually break. The Full Carbide Head on the Expert SDS plus-7X is an advanced 4-cutter design made from a single piece of the toughest metal: It doesn’t jam and presents no weakness on impact.Thanks to Bosch Carbide Technology and the Full Carbide Head, the Expert SDS plus-7X lasts far longer than regular hammer drill bits. It punches through rebar effectively so there is no need to stop, re-target or change bits when you strike steel.For construction professionals drilling concrete an…

These Faithfull SDS Plus Chisel Bits are made from drop-forged chrome molybdenum with a heat-treated tempered edge. Molybdenum is ideally suited for chisels because of its known reputation for hardness, toughness and wear resistance. Used mainly for light demolition, chiselling, stripping plaster, mortar chasing, channelling and breaking through brickwork.1 x Faithfull SDS Plus Chasing Gouge 22mm Length 250mmAdditional Information:• Type: Gouge• Size: 22 x 250mm

Lasts up to 3x longer than a standard drill bitDrilling through reinforced concrete is a tough job, and it has traditionally taken its toll on drill bits. Regular two-cutter bits get stuck in rebar and they eventually break. The Full Carbide Head on the Expert SDS plus-7X is an advanced 4-cutter design made from a single piece of the toughest metal: It doesn’t jam and presents no weakness on impact.Thanks to Bosch Carbide Technology and the Full Carbide Head, the Expert SDS plus-7X lasts far longer than regular hammer drill bits. It punches through rebar effectively so there is no need to stop, re-target or change bits when you strike steel.For construction professionals drilling concrete an…

The Makita Performance SDS Plus range consists of European manufactured hammer drill bits with a patented high volume multi-flute that quickly channels the drilling dust from the hole, saving both time and money. Due to its aggressive design, the fast and durable carbide tip allows easy centering and spot drilling. Designed for regular professional use, providing excellent performance in the toughest of materials. Also excellent for drilling in high resistance materials such as Green Concrete or Engineering Brick. The unique reinforced flute geometry transfers more impact energy from the rotary hammer to the drill head, reducing stress for user and power tool. The design and technology innovations …

The SDS plus-7 Drill Bit performs precision-drilling in reinforced concrete. Its full carbide head with 5 cutters is fused with IDS welding technology to drill with a very high level of accuracy. A vibration-reduced power transfer from the rotary hammer to the full carbide head is provided by the 2 + 2 flute design, which is made of high-alloy steel and created using optimised hardening technology. This offers the stability necessary for exact results. To prevent wandering and obtain a precise hole diameter, the Activeteq centring tip guides the drill position from the start. The bit is intended for use on masonry, concrete and reinforced concrete. To achieve accurate results, the visibility …

High quality metal twist drill bits for precise drilling in metal. Made out of high speed steel (HSS). A finely-tuned material elasticity provides for a long service life. Very good concentricity. Tough viscous tempered bits ensure a particularly long service life. The hexagonal shaft ensures very good power transfer. Drive: ¼" hexagon, suitable for holders as per DIN ISO 1173-D 6.3. Features and Benefits: • Twist bit for metal applications • Hex shaft for very good power transfer • HSS = high speed steel with split point • Finely-tuned material elasticity for great durability • Very good concentricity Contents: 848 HSS Metal Twist Drill Bits, 6 x 50 mm

Osborn Goldex 81504 series jobber drill bits.High Quaility HSS fully ground Titanium Coated Drill point for longer life. Suitable for drilling in steel, cast steel (alloyed and non alloyed), grey cast iron, graphite and malleable cast iron. Specifications • Standards: DIN 338 • Composition: High Speed Steel • Point Angle: 118° • Point Type & Helix Angle: N ~ 30° • Drill Body Tolerance: h8

Up to 5x more precise than a standard drill bitThe modern construction site requires working on many different materials, and you never know what you will need to drill next. Finding the right drill bit can be difficult and time-consuming – unless you have the Expert MultiConstruction Drill Bit.This highly versatile drill bit can drill accurately into hard materials such as tile and granite without skidding, thanks to its sharp tip and advanced geometric design. Made from optimised carbide using our fine grinding manufacturing technique, it can also tackle concrete, brick, wood and metal. It can always do a professional job – whatever the material.The Bosch Expert CYL-9 MultiConstruction Cyli…

The HSS Twist Drill Bit Ground is for drilling through metal with maximum precision. The bit's exposed 135-degree self-centring split-point tip combines active cutting and perfect centring without wandering, delivering maximum precision. The split-point tip also eliminates any need to pre-punch or pilot drill for up to 10 mm. This precision-ground bit made of HSS (high-speed steel) enables up to 40% faster drilling rate and up to 50% lower feed pressure than standard-ground HSS drill bits with chisel edges. This bit is designed for drilling holes in alloyed and non-alloyed steel, cast steel, cast iron, sintered iron, malleable cast iron, non-ferrous metals and hard plastics. The HSS Twist Drill …

Faithfull Tri-Point Speed Auger Bits will drill fast and clean holes in all types of wood. The three spurs and cutting edges create perfectly round holes with less chance of binding in the workpiece. Three flutes offer efficient waste removal making them much faster than traditional bits. A self-feeding screw tip enables accurate centring and pulls the bit through the wood. Precision machined from high-quality carbon steel with ground and honed cutting edges. The quick-release 1/4in hex shank is impact rated for use in impact drivers as well as all other corded and cordless drills. Specification: Overall Length: 159mm1 x Faithfull Tri-Point Speed Auger Bit 16mmAdditional Information:• Diameter: …

The Irwin IRW10502184 Speedhammer Max pointed chisel 280mm.

Faithfull Cold Chisels are made from high-quality grade steel which is hardened and ground to maximise safety and to ensure longer lasting cutting edges. For cutting brick, concrete and paving slabs. The cutting edge has an angle of approximately 60. Manufactured to BS 3066.

Faithfull Combination Wood Auger Bits can be used in either a hand or power drill at low speeds. Machined from high quality carbon steel, they feature a pitched screw point for accurate starting with a wide flat spiral for improved stability, straight tracking and fast waste removal. Augers may be used in timber, plywood, MDF and blockwood and can be resharpened using a hand file.

• Width: 20mm. • Model No. X2CHTechnical Specification:Length: 400mmWidth: 20mmDimensions: Length: 20mm x Height: 480mmWeight: 0.728KgWarranty: Consumable

Expert Quality, flat wood bits with a precision ground central point and enhanced design cutting edge spurs, which deliver greater waste removal compared with standard flat wood bits. Made from high quality carbon steel that's correctly hardened and tempered. Each cutting edge is expertly ground and finished for maximum performance. Ideal for use with combi drills, drill drivers and impact drivers. All sizes have a strong 6mm shank.

The IRWIN® HSS Pro Drill Bits are made from high-performance, high-speed steel. They have a 118° split point shape for increased performance and very good centring. The drill bits ensure precision starting, with no need to pre-punch or pilot drill. They penetrate the material quickly, requiring little effort and feed pressure. Manufactured to DIN 338 standards. DIN 338 drill bits are suitable for many trade and industrial applications in alloyed and unalloyed steel, non-ferrous metal, cast iron and plastics.This IRWIN® HSS Reduced Shank Pro Drill Bit has the following specification: Diameter: 11.0mmWorking Length: 94mmTotal Length: 142mmShank Diameter: 10mmAdditional Information:• …

Osborn Goldex 81504 series jobber drill bits.High Quaility HSS fully ground Titanium Coated Drill point for longer life. Suitable for drilling in steel, cast steel (alloyed and non alloyed), grey cast iron, graphite and malleable cast iron. Specifications • Standards: DIN 338 • Composition: High Speed Steel • Point Angle: 118° • Point Type & Helix Angle: N ~ 30° • Drill Body Tolerance: h8

The HSS Twist Drill Bit PointTeQ enables fast drilling in metal due to its PointTeQ tip design. Quick and easy drilling starts are possible as the self-centering tip prevents wandering. Because of its increased drilling rate, less heat and wear are generated. The PointTeQ tip design remains sharp and ensures continuous durability. This bit is suitable for drilling clearance and pilot holes in alloyed and non-alloyed steel, non-ferrous metals, cast steel, cast iron and plastics. There is a low risk of breakage, especially for drill bits below 6 mm in diameter as the bit is manufactured to have a highly elastic body. Its black-oxide coated flute provides fast chip removal. The HSS Twist Drill …

Faithfull Impact Rated Flat Bits are designed to perform fast, clean cuts, will bore all types of timber and are equally efficient when drilling with or against the grain. All bits have a precision ground point and cutting surfaces with extended spurs for faster cutting. All sizes except the 6mm, have a non-slip hexagonal shank with a locking mechanism compatible with adaptors or chucks with a built-in quick-release feature. A 300mm extension shank is available for use with flat bits of 16mm and above, for deep drill applications. Ideal for use with both mains or cordless drills. Made to DIN 3126 quality with 1/4in hexagonal non-slip shaft.

This drill bit has a hexagonal shank system and works with all drill drivers with a 13-mm chuck. The Auger Bit is ideal for fast drilling-accuracy when producing through-holes, pre-drilling for rafter nails and drilling deep dowel holes in wood. The heavy-duty self-feeding tip pulls the bit through completely, which allows for quick and effortless precision-drilling. Straight holes and a high chip removal rate and increased speed are made possible by the bit's optimised low-friction flute geometry with a solid centre. Its optimised scoring spur and precision-ground main cutting edge produce accurate holes. It is ideal for use in the ancillary building trades, for carpenters and roofers, and …

Impact rated drill bit with 1/4" hex shank optimised for impact drivers. Titanium Nitride coating dispenses heat and makes the drill bit suitable for use also in high speed. Quad Edge Tip unique combination of 135° split point and four cutting edges 135° split point allows for precise and fast drilling start without walking. Four cutting edges create smaller chips to prevent heat build up for longer life. Variable flute geometry for faster material ejection and helps the bit run cooler and prevent it from burning out faster. Wider core towards the shank of the drill bit strengthens the core to increase overall flute durability. Specifications • Diameter: 9mm • Total Length: …

Stanley drill bits are designed to resist the impacts and fast drilling on concrete. The flute design removes the debris from the hole contribution for longer drill bit life. The hardened steel construction of the drill bit ensures exceptional strength, allowing it to withstand the toughest drilling applications. Whether you are working on soft or hard surfaces, its reinforced carbide tip provides maximum durability and longevity, ensuring consistent performance throughout projects. Features & Benefits • For drilling into house bricks and masonry • Shank diameter of drill bits 10-13mm is reduced to 9.5mm • Diameters larger than 13mm shank is reduced to 12.7mm • For use with …