Drill Bits

The HSS Twist Drill Bit PointTeQ enables fast drilling in metal due to its PointTeQ tip design. Quick and easy drilling starts are possible as the self-centering tip prevents wandering. Because of its increased drilling rate, less heat and wear are generated. The PointTeQ tip design remains sharp and ensures continuous durability. This bit is suitable for drilling clearance and pilot holes in alloyed and non-alloyed steel, non-ferrous metals, cast steel, cast iron and plastics. There is a low risk of breakage, especially for drill bits below 6 mm in diameter as the bit is manufactured to have a highly elastic body. Its black-oxide coated flute provides fast chip removal. The HSS Twist Drill …

Faithfull Cold Chisels are made from high-quality grade steel which is hardened and ground to maximise safety and to ensure longer lasting cutting edges. For cutting brick, concrete and paving slabs. The cutting edge has an angle of approximately 60. Manufactured to BS 3066.

The SDS plus-3 Drill Bit offers durability when drilling in concrete. To prevent heat development, the 4-flute dura design provides effective dust removal for increased endurance. It is made of high-alloy steel, which is produced with an optimised hardening technology to withstand wear. For additional resistance, indented cutting edges are made from an ideal Bosch-controlled carbide blend. As proof of quality, the drill bit bears the test mark of the PGM Masonry Drill Bit Association Board, guaranteeing compliance with tight tolerances, exact drilling and the firm hold of fixings. The bit is intended for work on concrete and masonry and is to be used with rotary hammers with SDS plus holders.…

Superior quality auger wood drill bit has a hexagonal shank for higher torque ranges demanded by this drill type. Fully hardened with a screw point to aid location and smooth drilling. Supplied in a plastic wallet. Features & Benefits: • Superior quality auger wood drill bit has a hexagonal shank for higher torque ranges demanded by this drill type. • Fully hardened with a screw point to aid location and smooth drilling. • Supplied in a plastic wallet. • Model No. AW18X460 Specifications: Model No AW18x460 Brand: Worksafe Size: Ø18 x 460mm

The HSS Twist Drill Bit Titanium offers maximum lifetime while drilling holes in metal. When using the appropriate cooling system, the drill bit has the lowest possible level of friction and minimal wear, due to its titanium-nitride coating. The high surface quality of this ground twist drill bit, which is made from HSS (high-speed steel), allows for extended usage. It is suitable for use on alloyed and non-alloyed steel, malleable cast iron, sintered iron, new silver, copper, bronze and hard plastics such as perspex. The HSS Twist Drill Bit Titanium is manufactured to DIN 338. The drill bit is Type N (flute angle) with a 135-degree tip and a diameter tolerance of h8. Active cutting and perfect …

An economical bit for cutting quick holes in timber. With centre point, back tapered cutting edge and ground chip breakers. Specifications: • Shank Diameter: 1/4 hex • Dia Metric: 16 • Overall Length Metric: 152

The Irwin Turbomax range of drill bits are suitable for portable and cordless drills. They are primarily designed for drilling metal and sheet metal but also performs exceedingly well in all types of wood and plastics and can be used for drilling stainless steel. Please note that if used for drilling stainless steel, a coolant should always be used.Irwin Turbomax HSS Drill Bit (2). Size: 10.0 x 133mm.Working Length: 83mmAdditional Information:• Tip Diameter: 10.0mm• Working Length: 83mm• Overall Length: 133mm• Pack Qty.: 1

The CWC TCT series pilot pins are compatible with rotabroach TCT cutters from a 18mm to 52mm diameter and 35mm depth of cut.

The SDS plus-5 Drill Bit allows for effortless drilling. For smooth work, the carbide plate is grooved and bears notches that penetrate material more easily and prevent jamming in concrete. Drill guidance for easy starts without jarring or wandering is provided by the Activeteq centring tip, which keeps the drill in place for a precise hole diameter. Furthermore, AWB brazing and hardening technology reduces vibration during drilling to minimise strain on the user. The bit is intended for use on masonry and concrete. To achieve accurate results, the visibility of the wear mark indicates if the diameter of the hole is still in tolerance for metal anchor setting. As proof of quality, the drill …

The SDS plus-7 Drill Bit performs precision-drilling in reinforced concrete. Its full carbide head with 5 cutters is fused with IDS welding technology to drill with a very high level of accuracy. A vibration-reduced power transfer from the rotary hammer to the full carbide head is provided by the 2 + 2 flute design, which is made of high-alloy steel and created using optimised hardening technology. This offers the stability necessary for exact results. To prevent wandering and obtain a precise hole diameter, the Activeteq centring tip guides the drill position from the start. The bit is intended for use on masonry, concrete and reinforced concrete. To achieve accurate results, the visibility …

Expert Quality, tungsten carbide tipped straight shank drills with milled flute. Suitable for use with power drills. Manufactured to ISO 5468 Specifications Contents: 1 x Masonry Drill Bit, 13 x 200mm

Lasts up to 3x longer than a standard drill bitDrilling through reinforced concrete is a tough job, and it has traditionally taken its toll on drill bits. Regular two-cutter bits get stuck in rebar and they eventually break. The Full Carbide Head on the Expert SDS plus-7X is an advanced 4-cutter design made from a single piece of the toughest metal: It doesn’t jam and presents no weakness on impact.Thanks to Bosch Carbide Technology and the Full Carbide Head, the Expert SDS plus-7X lasts far longer than regular hammer drill bits. It punches through rebar effectively so there is no need to stop, re-target or change bits when you strike steel.For construction professionals drilling concrete an…

Lasts up to 3x longer than a standard drill bitDrilling through reinforced concrete is a tough job, and it has traditionally taken its toll on drill bits. Regular two-cutter bits get stuck in rebar and they eventually break. The Full Carbide Head on the Expert SDS plus-7X is an advanced 4-cutter design made from a single piece of the toughest metal: It doesn’t jam and presents no weakness on impact.Thanks to Bosch Carbide Technology and the Full Carbide Head, the Expert SDS plus-7X lasts far longer than regular hammer drill bits. It punches through rebar effectively so there is no need to stop, re-target or change bits when you strike steel.For construction professionals drilling concrete an…

Lasts up to 3x longer than a standard drill bitDrilling through reinforced concrete is a tough job, and it has traditionally taken its toll on drill bits. Regular two-cutter bits get stuck in rebar and they eventually break. The Full Carbide Head on the Expert SDS plus-7X is an advanced 4-cutter design made from a single piece of the toughest metal: It doesn’t jam and presents no weakness on impact.Thanks to Bosch Carbide Technology and the Full Carbide Head, the Expert SDS plus-7X lasts far longer than regular hammer drill bits. It punches through rebar effectively so there is no need to stop, re-target or change bits when you strike steel.For construction professionals drilling concrete an…

These Faithfull SDS Plus Chisel Bits are made from drop-forged chrome molybdenum with a heat-treated tempered edge. Molybdenum is ideally suited for chisels because of its known reputation for hardness, toughness and wear resistance. Used mainly for light demolition, chiselling, stripping plaster, mortar chasing, channelling and breaking through brickwork.1 x Faithfull SDS Plus Chasing Gouge 22mm Length 250mmAdditional Information:• Type: Gouge• Size: 22 x 250mm

The HSS Twist Drill Bit PointTeQ enables fast drilling in metal due to its PointTeQ tip design. Quick and easy drilling starts are possible as the self-centering tip prevents wandering. Because of its increased drilling rate, less heat and wear are generated. The PointTeQ tip design remains sharp and ensures continuous durability. This bit is suitable for drilling clearance and pilot holes in alloyed and non-alloyed steel, non-ferrous metals, cast steel, cast iron and plastics. There is a low risk of breakage, especially for drill bits below 6 mm in diameter as the bit is manufactured to have a highly elastic body. Its black-oxide coated flute provides fast chip removal. The HSS Twist Drill …

The HSS-R construction of this drill bit guarantees exceptional durability and heat resistance, owing to the high-speed steel composition. Rapid chip removal during drilling minimizes heat buildup, extending the drill bit's lifespan. The precision-ground tip enhances cutting efficiency, allowing for smooth and precise drilling in metal surfaces. With a diameter of 11mm and a length of 142mm, this drill bit excels in drilling through various metals, including steel and aluminium. Its design ensures clean and accurate holes, making it an indispensable addition to your toolkit for metal fabrication, construction, and other demanding applications. The 11mm diameter provides the strength and precision …

Ideal for clean accurate drilling in metal, laminates, plastics and wood. Straight shank HSS jobber drill bit

Osborn Goldex 81504 series jobber drill bits.High Quaility HSS fully ground Titanium Coated Drill point for longer life. Suitable for drilling in steel, cast steel (alloyed and non alloyed), grey cast iron, graphite and malleable cast iron. Specifications • Standards: DIN 338 • Composition: High Speed Steel • Point Angle: 118° • Point Type & Helix Angle: N ~ 30° • Drill Body Tolerance: h8

The solid carbide construction ensures exceptional hardness and wear resistance, making it perfect for drilling through tough materials like stainless steel, cast iron, and hardened metals. The TiN (Titanium Nitride) tip coating enhances the drill's cutting efficiency and longevity by reducing friction and heat buildup. This allows for faster drilling speeds and extended tool life. Designed with a jobber length, the Dormer R003 offers optimal balance between rigidity and reach, ensuring accurate and clean holes every time. Features & Benefits • Bright and TiN tip coating • Hard material solid carbide • 120° drill point • Cylindrical shank/straight shank • Standard …

Crafted from high-speed steel (HSS) with a titanium nitride (TiN) coating, this drill bit offers exceptional durability and heat resistance, ensuring long-lasting performance in a variety of drilling applications. This jobber drill bit is ideal for creating precise and accurate holes in metal, wood, plastic, and other materials. The TiN coating reduces friction and heat buildup during drilling, resulting in smoother drilling and extended tool life. Features & Benefits • Versatile bit for both hand-held and machine drilling • Titanium Nitride Tipped (2mm and above) • Bright finish and conventional point (below 2mm) • DIN 338 • Specially designed 118° Point Angle Specifications …

Faithfull Combination Wood Auger Bits can be used in either a hand or power drill at low speeds. Machined from high quality carbon steel, they feature a pitched screw point for accurate starting with a wide flat spiral for improved stability, straight tracking and fast waste removal. Augers may be used in timber, plywood, MDF and blockwood and can be resharpened using a hand file.

• Forged steel with tungsten carbide tip • Optimised design for fast and accurate drilling of concrete, stone & brick • Diameter: 16 mm • Total length: 150 mm Specifications: Diameter = 16mm Overall length = 150mm

Ideal for general-purpose drilling into most masonry materials. For use in a 1/2" chuck with percussion. Supplied in a plastic wallet. Features & Benefits: • Ideal for general-purpose drilling into most masonry materials. For use in a 1/2" chuck with percussion. • Supplied in a plastic wallet. • Model No. SS13X600 Specifications: Model No SS13X600 Brand: Worksafe Size: Ø13 x 600mm