Drill Bits

Faithfull Impact Rated Flat Bits are designed to perform fast, clean cuts, will bore all types of timber and are equally efficient when drilling with or against the grain. All bits have a precision ground point and cutting surfaces with extended spurs for faster cutting. All sizes except the 6mm, have a non-slip hexagonal shank with a locking mechanism compatible with adaptors or chucks with a built-in quick-release feature. A 300mm extension shank is available for use with flat bits of 16mm and above, for deep drill applications. Ideal for use with both mains or cordless drills. Made to DIN 3126 quality with 1/4in hexagonal non-slip shaft.

Milwaukee HSS-G Thunderweb Drill Bit design is characterised by a conical shaped web which gets thicker towards the back of the drill bit. Standard drill bits have a constant thickness throughout their length. Even at the narrowest point the Tunderweb core is thicker than that of a standard drill bit. Specifications • Cutting Width: 2.3mm • Length: 53mm • Pack Quantity: 10Features & Benefits• Parabolic web cross section: Large web thickness and strength built in • Thunderweb flute form ejects hot chips rapidly • Dissipates heat better increasing life time • Precision starting, drill bit won't walk on material surface • Polished finish reduces friction …

Lasts up to 3x longer than a standard drill bitDrilling through reinforced concrete is a tough job, and it has traditionally taken its toll on drill bits. Regular two-cutter bits get stuck in rebar and they eventually break. The Full Carbide Head on the Expert SDS plus-7X is an advanced 4-cutter design made from a single piece of the toughest metal: It doesn’t jam and presents no weakness on impact.Thanks to Bosch Carbide Technology and the Full Carbide Head, the Expert SDS plus-7X lasts far longer than regular hammer drill bits. It punches through rebar effectively so there is no need to stop, re-target or change bits when you strike steel.For construction professionals drilling concrete an…

High quality metal twist drill bits for precise drilling in metal. Made out of high speed steel (HSS). A finely-tuned material elasticity provides for a long service life. Very good concentricity. Tough viscous tempered bits ensure a particularly long service life. The hexagonal shaft ensures very good power transfer. Drive: ¼" hexagon, suitable for holders as per DIN ISO 1173-D 6.3. Features and Benefits: • Twist bit for metal applications • Hex shaft for very good power transfer • HSS = high speed steel with split point • Finely-tuned material elasticity for great durability • Very good concentricity Contents: 848 HSS Metal Twist Drill Bits, 3.1 x 40 mm

The Faithfull Bevel Edged Chisel range are quality tools for professional work as well as DIY users. The blue PVC handles on these chisels are impact resistant and designed for use with a mallet or an occasional hammer blow. Each blade is manufactured from drop-forged chrome vanadium steel that is hardened and tempered to exacting standards, ensuring that the cutting edge remains sharper for longer. The bevelled edges make these chisels ideal for fine work and for cutting into tight corners. All the chisels in this range are supplied with blade guards.

Ideal for clean accurate drilling in metal, laminates, plastics and wood. Straight shank HSS jobber drill bit

Irwin Speedhammer Pointed Chisels are for use with SDS Max machines. Suitable for a wide range of applications: breaking through, breaking up concrete, light demolition work and chasing of channels for pipes and electrical conduit. Suitable for use on concrete and masonry and are supplied in a grey sandblasted professional finish.The Irwin IRW10502184 Speedhammer Max pointed chisel 280mm.Additional Information:• Type: Point• Size: 280mm

Osborn Goldex 81504 series jobber drill bits.High Quaility HSS fully ground Titanium Coated Drill point for longer life. Suitable for drilling in steel, cast steel (alloyed and non alloyed), grey cast iron, graphite and malleable cast iron. Specifications • Standards: DIN 338 • Composition: High Speed Steel • Point Angle: 118° • Point Type & Helix Angle: N ~ 30° • Drill Body Tolerance: h8

These Faithfull Professional Cobalt Jobber Drill Bits are manufactured from M35 HSSE grade steel with a 5% cobalt content for increased heat resistance and cutting performance. All bits are fully ground and feature a 135° non-slip split point for precise centring and are produced in accordance to DIN 388 for high precision tolerances and geometric accuracy. Cobalt bits cut faster and last longer and are suitable for heavy-duty industrial work in: Alloy steels, carbon steels, cast iron, hardened alloy steels, stainless steels, high temperature alloys, Titanium alloy, high strength steel and carbon fibre composite materials.These Faithfull Professional Cobalt Jobber Drill Bits are supplied …

The HSS Twist Drill Bit Titanium offers maximum lifetime while drilling holes in metal. When using the appropriate cooling system, the drill bit has the lowest possible level of friction and minimal wear, due to its titanium-nitride coating. The high surface quality of this ground twist drill bit, which is made from HSS (high-speed steel), allows for extended usage. It is suitable for use on alloyed and non-alloyed steel, malleable cast iron, sintered iron, new silver, copper, bronze and hard plastics such as perspex. The HSS Twist Drill Bit Titanium is manufactured to DIN 338. The drill bit is Type N (flute angle) with a 135-degree tip and a diameter tolerance of h8. Active cutting and perfect …

Lasts up to 3x longer than a standard drill bitDrilling through reinforced concrete is a tough job, and it has traditionally taken its toll on drill bits. Regular two-cutter bits get stuck in rebar and they eventually break. The Full Carbide Head on the Expert SDS plus-7X is an advanced 4-cutter design made from a single piece of the toughest metal: It doesn’t jam and presents no weakness on impact.Thanks to Bosch Carbide Technology and the Full Carbide Head, the Expert SDS plus-7X lasts far longer than regular hammer drill bits. It punches through rebar effectively so there is no need to stop, re-target or change bits when you strike steel.For construction professionals drilling concrete an…

The Faithfull Bevel Edged Chisel range are quality tools for professional work as well as DIY users. The blue PVC handles on these chisels are impact resistant and designed for use with a mallet or an occasional hammer blow. Each blade is manufactured from drop-forged chrome vanadium steel that is hardened and tempered to exacting standards, ensuring that the cutting edge remains sharper for longer. The bevelled edges make these chisels ideal for fine work and for cutting into tight corners. All the chisels in this range are supplied with blade guards.

The Rotabroach RA356 pilot pin is compatible with Rotabroach TCT cutters from 18mm - 65mm diameter with 50mm depth of cut and Rotabroach Imperial cutters from 11/16" - 2 3/8" diameter with 2" depth of cut.

The HSS Twist Drill Bit Ground is for drilling through metal with maximum precision. The bit's exposed 135-degree self-centring split-point tip combines active cutting and perfect centring without wandering, delivering maximum precision. The split-point tip also eliminates any need to pre-punch or pilot drill for up to 10 mm. This precision-ground bit made of HSS (high-speed steel) enables up to 40% faster drilling rate and up to 50% lower feed pressure than standard-ground HSS drill bits with chisel edges. This bit is designed for drilling holes in alloyed and non-alloyed steel, cast steel, cast iron, sintered iron, malleable cast iron, non-ferrous metals and hard plastics. The HSS Twist Drill …

Expert Quality, tungsten carbide tipped straight shank drills with milled flute. Suitable for use with power drills. Manufactured to ISO 5468 Specifications Contents: 1 x Masonry Drill Bit, 12 x 200mm

These high-performance Faithfull Tungsten Carbide Tipped Drill Bits fit into SDS Plus chucks which provide a particularly secure non-slip grip that transmits maximum power for rotary percussion drilling, mainly into concrete. The SDS Plus bits ensure maximum power transmission due to their unique fluted shaft. This effectively removes situations where a perfectly serviceable cutting edge is rendered useless by a worn shank. The SDS Plus system also enables faster changing of drills using a quick release keyless chuck. For use in bricks, blocks, concrete containing aggregates, marble and hard stone, and other hard masonry materials.

Expert Quality, tungsten carbide tipped straight shank drills with milled flute. Suitable for use with power drills. Manufactured to ISO 5468 Specifications Contents: 1 x Masonry Drill Bit, 14 x 150mm

Lasts up to 3x longer than a standard drill bitDrilling through reinforced concrete is a tough job, and it has traditionally taken its toll on drill bits. Regular two-cutter bits get stuck in rebar and they eventually break. The Full Carbide Head on the Expert SDS plus-7X is an advanced 4-cutter design made from a single piece of the toughest metal: It doesn’t jam and presents no weakness on impact.Thanks to Bosch Carbide Technology and the Full Carbide Head, the Expert SDS plus-7X lasts far longer than regular hammer drill bits. It punches through rebar effectively so there is no need to stop, re-target or change bits when you strike steel.For construction professionals drilling concrete an…

High quality metal twist drill bits for precise drilling in metal. Made out of high speed steel (HSS). A finely-tuned material elasticity provides for a long service life. Very good concentricity. Tough viscous tempered bits ensure a particularly long service life. The hexagonal shaft ensures very good power transfer. Drive: ¼" hexagon, suitable for holders as per DIN ISO 1173-D 6.3. Features and Benefits: • Twist bit for metal applications • Hex shaft for very good power transfer • HSS = high speed steel with split point • Finely-tuned material elasticity for great durability • Very good concentricity Contents: 848 HSS Metal Twist Drill Bits, 5.1 x 50 mm

The SDS plus-5X Drill Bit offers highly efficient drilling in reinforced concrete. The geometrical form of the 4-cutter head prevents jamming and breakage for optimal results. The “turn-angle” head and the large and short dust removal channels within the 4-flute design provide fast dust removal so the bit can slice through concrete and rebar quickly with reduced wear. For efficient work and exact hole diameters, the centring tip guides drilling from the start, to prevent wandering, which can falsify the hole diameter. The bit is intended for use on masonry, concrete and reinforced concrete. As proof of quality, the drill bit bears the test mark of the PGM Masonry Drill Bit Association Board, gua…

An economical bit for cutting quick holes in timber. With centre point, back tapered cutting edge and ground chip breakers. Specifications: • Shank Diameter: 1/4 hex • Dia Metric: 12 • Overall Length Metric: 152

SDS Drill Bit 12x140x200mmC.K SDS Concrete Drill Bit 12x140x200mm~ Tungsten carbide tipped with optimized geometry for drilling concrete and stone~ Vacuum brazed tips for durability~ Ground flutes designed for optimum debris removal~ SDS-plus shank~ Diameter: 12 mm~ Working length: 140 mm~ Total length: 200 mmTechnical DataDiameter: 12mmWorking length: 140mmOverall length: 200mmComponent Material:Tungsten tipTechnical Specification:CE Certified: NoConflict Materials Content : YesConflict material Country of Origin: GermanyConflict material Name of substance: TungstenREACH Content Status SVHC Free or Contains SVHC: SVHC freeRoSH Regs Within Scope: NoBatteries Included: NoBattery Powered: NoCharger …

High quality metal twist drill bits for precise drilling in metal. Made out of high speed steel (HSS). A finely-tuned material elasticity provides for a long service life. Very good concentricity. Tough viscous tempered bits ensure a particularly long service life. The hexagonal shaft ensures very good power transfer. Drive: ¼" hexagon, suitable for holders as per DIN ISO 1173-D 6.3. Features and Benefits: • Twist bit for metal applications • Hex shaft for very good power transfer • HSS = high speed steel with split point • Finely-tuned material elasticity for great durability • Very good concentricity Contents: 848 HSS Metal Twist Drill Bits, 4 x 44 mm

The Dormer A225 HSS Centre Drill is a precision tool designed for creating accurate centre holes in workpieces, essential for facilitating subsequent drilling operations. Made from High-Speed Steel, this centre drill offers exceptional durability and performance, capable of handling various materials including steel, stainless steel, and non-ferrous metals. Its high-quality construction ensures excellent resistance to wear and heat, maintaining sharpness and precision even under demanding conditions. The 60-degree included angle of the centre drill guarantees precise centering and optimal hole preparation, reducing the risk of tool deflection and ensuring accurate alignment for follow-up drilling.…