Drill Bits

The HSS Twist Drill Bit Ground is for drilling through metal with maximum precision. The bit's exposed 135-degree self-centring split-point tip combines active cutting and perfect centring without wandering, delivering maximum precision. The split-point tip also eliminates any need to pre-punch or pilot drill for up to 10 mm. This precision-ground bit made of HSS (high-speed steel) enables up to 40% faster drilling rate and up to 50% lower feed pressure than standard-ground HSS drill bits with chisel edges. This bit is designed for drilling holes in alloyed and non-alloyed steel, cast steel, cast iron, sintered iron, malleable cast iron, non-ferrous metals and hard plastics. The HSS Twist Drill …

Lasts up to 3x longer than a standard drill bitDrilling through reinforced concrete is a tough job, and it has traditionally taken its toll on drill bits. Regular two-cutter bits get stuck in rebar and they eventually break. The Full Carbide Head on the Expert SDS plus-7X is an advanced 4-cutter design made from a single piece of the toughest metal: It doesn’t jam and presents no weakness on impact.Thanks to Bosch Carbide Technology and the Full Carbide Head, the Expert SDS plus-7X lasts far longer than regular hammer drill bits. It punches through rebar effectively so there is no need to stop, re-target or change bits when you strike steel.For construction professionals drilling concrete an…

Faithfull Plug Cutters are used in combination with screwsinks to prepare perfectly sized plugs to fill counterbored holes. For best performance, the power drill should be held in a stand. For a perfect grain match use an offcut from the timber being plugged. To ensure an accurate fit we suggest you use the same screwsink from the Faithfull brand. The set of 4 contains sizes No 6, 8, 10 and 12.Cuts Size 13 mm PlugsAdditional Information:• Type: Plug Cutter• Screw Compatibility: 13mm

Expert Quality, flat wood bits with a precision ground central point and enhanced design cutting edge spurs, which deliver greater waste removal compared with standard flat wood bits. Made from high quality carbon steel that's correctly hardened and tempered. Each cutting edge is expertly ground and finished for maximum performance. Ideal for use with combi drills, drill drivers and impact drivers. All sizes have a strong 6mm shank.

The HSS Twist Drill Bit Ground is for drilling through metal with maximum precision. The bit's exposed 135-degree self-centring split-point tip combines active cutting and perfect centring without wandering, delivering maximum precision. The split-point tip also eliminates any need to pre-punch or pilot drill for up to 10 mm. This precision-ground bit made of HSS (high-speed steel) enables up to 40% faster drilling rate and up to 50% lower feed pressure than standard-ground HSS drill bits with chisel edges. This bit is designed for drilling holes in alloyed and non-alloyed steel, cast steel, cast iron, sintered iron, malleable cast iron, non-ferrous metals and hard plastics. The HSS Twist Drill …

The Blue Spot Tools 4-22mm Step Drill is specially designed for precision drilling of holes in aluminium, brass, copper, plastic, steel and wood. Manufactured from high steel for increased durability and cutting power. Titanium coated to reduce friction and heat. 2mm step increments. Additional Information:• Size Range: 4-22mm• No. of Steps: 10

Ideal for clean accurate drilling in metal, laminates, plastics and wood. Straight shank HSS jobber drill bit

Up to 5x more precise than a standard drill bitThe modern construction site requires working on many different materials, and you never know what you will need to drill next. Finding the right drill bit can be difficult and time-consuming – unless you have the Expert MultiConstruction Drill Bit.This highly versatile drill bit can drill accurately into hard materials such as tile and granite without skidding, thanks to its sharp tip and advanced geometric design. Made from optimised carbide using our fine grinding manufacturing technique, it can also tackle concrete, brick, wood and metal. It can always do a professional job – whatever the material.The Bosch Expert CYL-9 MultiConstruction Cyli…

Stanley drill bits are designed to resist the impacts and fast drilling on concrete. The flute design removes the debris from the hole contribution for longer drill bit life. The hardened steel construction of the drill bit ensures exceptional strength, allowing it to withstand the toughest drilling applications. Whether you are working on soft or hard surfaces, its reinforced carbide tip provides maximum durability and longevity, ensuring consistent performance throughout projects. Features & Benefits • For drilling into house bricks and masonry • Shank diameter of drill bits 10-13mm is reduced to 9.5mm • Diameters larger than 13mm shank is reduced to 12.7mm • For use with …

High quality metal twist drill bits for precise drilling in metal. Made out of high speed steel (HSS). A finely-tuned material elasticity provides for a long service life. Very good concentricity. Tough viscous tempered bits ensure a particularly long service life. The hexagonal shaft ensures very good power transfer. Drive: ¼" hexagon, suitable for holders as per DIN ISO 1173-D 6.3. Features and Benefits: • Twist bit for metal applications • Hex shaft for very good power transfer • HSS = high speed steel with split point • Finely-tuned material elasticity for great durability • Very good concentricity Contents: 848 HSS Metal Twist Drill Bits, 6 x 50 mm

The HSS Twist Drill Bit Titanium offers maximum lifetime while drilling holes in metal. When using the appropriate cooling system, the drill bit has the lowest possible level of friction and minimal wear, due to its titanium-nitride coating. The high surface quality of this ground twist drill bit, which is made from HSS (high-speed steel), allows for extended usage. It is suitable for use on alloyed and non-alloyed steel, malleable cast iron, sintered iron, new silver, copper, bronze and hard plastics such as perspex. The HSS Twist Drill Bit Titanium is manufactured to DIN 338. The drill bit is Type N (flute angle) with a 135-degree tip and a diameter tolerance of h8. Active cutting and perfect …

• HSS roll forged blacksmith’s drill bit with a reduced shank to enable use with a standard chuck. • Drill has a black oxide finish. • 130mm Working length. • Supplied in a plastic wallet.HSS roll forged blacksmith’s drill bit with a reduced shank to enable use with a standard chuck. Drill has a black oxide finish and 130mm Working length. Supplied in a plastic wallet.• HSS roll forged blacksmith’s drill bit with a reduced shank to enable use with a standard chuck. • Drill has a black oxide finish. • 130mm Working length. • Supplied in a plastic wallet. • Model No. BSB17.5Technical Specification:Size: ø17.5 x 190mmDimensions: Length: 20mm x Height: 210mmWeight: 0.205KgWarranty: Consumabl…

Lasts up to 3x longer than a standard drill bitDrilling through reinforced concrete is a tough job, and it has traditionally taken its toll on drill bits. Regular two-cutter bits get stuck in rebar and they eventually break. The Full Carbide Head on the Expert SDS plus-7X is an advanced 4-cutter design made from a single piece of the toughest metal: It doesn’t jam and presents no weakness on impact.Thanks to Bosch Carbide Technology and the Full Carbide Head, the Expert SDS plus-7X lasts far longer than regular hammer drill bits. It punches through rebar effectively so there is no need to stop, re-target or change bits when you strike steel.For construction professionals drilling concrete an…

Faithfull Impact Rated Flat Bits are designed to perform fast, clean cuts, will bore all types of timber and are equally efficient when drilling with or against the grain. All bits have a precision ground point and cutting surfaces with extended spurs for faster cutting. All sizes except the 6mm, have a non-slip hexagonal shank with a locking mechanism compatible with adaptors or chucks with a built-in quick-release feature. A 300mm extension shank is available for use with flat bits of 16mm and above, for deep drill applications. Ideal for use with both mains or cordless drills. Made to DIN 3126 quality with 1/4in hexagonal non-slip shaft.

Expert Quality, tungsten carbide tipped straight shank drills with milled flute. Suitable for use with power drills. Display packed.

The SDS plus-5 Drill Bit allows for effortless drilling. For smooth work, the carbide plate is grooved and bears notches that penetrate material more easily and prevent jamming in concrete. Drill guidance for easy starts without jarring or wandering is provided by the Activeteq centring tip, which keeps the drill in place for a precise hole diameter. Furthermore, AWB brazing and hardening technology reduces vibration during drilling to minimise strain on the user. The bit is intended for use on masonry and concrete. To achieve accurate results, the visibility of the wear mark indicates if the diameter of the hole is still in tolerance for metal anchor setting. As proof of quality, the drill …

Faithfull Combination Wood Auger Bits can be used in either a hand or power drill at low speeds. Machined from high quality carbon steel, they feature a pitched screw point for accurate starting with a wide flat spiral for improved stability, straight tracking and fast waste removal. Augers may be used in timber, plywood, MDF and blockwood and can be resharpened using a hand file.

This spade bit has a 1/4-inch hex shank system and it is best for use with portable power drills. The Self-Cut Speed Spade Bit performs extremely fast hole drilling. Its self-feeding threaded tip enables the drill bit to effortlessly pull itself into the wood for high-speed drilling with little exertion. Fast chip removal for rapid results is made possible by the specially shaped spade. In product tests, this drill bit produces holes 10 times faster than a standard spade bit. It is suitable for use on soft and hard wood, light building materials and plasterboard. Total length 152 mm • Extremely Fast Holes • Self-Cut Speed Spade Bit performs extremely fast hole drilling • Self-feeding …

Full length bevel edged blades manufactured from carbon steel hardened, tempered, finely ground and clear lacquer coated for corrosion protection. Impact - resistant polypropylene handles. All blades have blade guards. Display packed.

The SDS plus-5 Drill Bit allows for effortless drilling. For smooth work, the carbide plate is grooved and bears notches that penetrate material more easily and prevent jamming in concrete. Drill guidance for easy starts without jarring or wandering is provided by the Activeteq centring tip, which keeps the drill in place for a precise hole diameter. Furthermore, AWB brazing and hardening technology reduces vibration during drilling to minimise strain on the user. The bit is intended for use on masonry and concrete. To achieve accurate results, the visibility of the wear mark indicates if the diameter of the hole is still in tolerance for metal anchor setting. As proof of quality, the drill …

The name of a pro
6 mm diameter drill bit
Compatible with corded and cordless drills
Manufactured from quality steel with a tungsten carbide tip to provide clean, precise drilling in ceramic and glazed tiles, and non-toughened glass

Expert Quality, tungsten carbide tipped straight shank drills with milled flute. Suitable for use with power drills. Display packed.

Designed with efficiency in mind, the innovative flute design promotes swift material removal and efficient debris evacuation, reducing the risk of bit binding and ensuring a smooth drilling experience. The robust construction of the bit ensures it can withstand the demands of tough applications, maintaining its sharpness and performance over time. The carbide tip ensures durability and longevity, making it the ideal tool for drilling into concrete, brick, stone, and other masonry materials. Features & Benefits • Flat carbide tip design for less breakage in the hardest of materials • Four flute design removes debris quickly for fast drilling • Hardened steel body for maximum strength …

The HEX-9 Ceramic Tile Drill Bit performs fast drilling in tiles. High-speed drilling is made possible by the 7-sided asymmetrical diamond-ground cutting edges, which efficiently slice through materials. The 2-flute U-shape design provides effective dust removal, which allows the drill to glide through the material quickly for fast results. This drill bit is intended for work in soft-to-medium density tiles, porcelain and ceramic. Only use this drill bit at low speeds and without the impact and hammer function. No cooling is required. It is compatible with impact drivers due to its hex-shank and it is suitable for use with standard drivers with chucks. Pack of 1 • Fast Drilling in Tiles …