Drill Bits

Full length bevel edged blades manufactured from carbon steel hardened, tempered, finely ground and clear lacquer coated for corrosion protection. Impact - resistant polypropylene handles. All blades have blade guards. Display packed.

The HSS Twist Drill Bit Titanium offers maximum lifetime while drilling holes in metal. When using the appropriate cooling system, the drill bit has the lowest possible level of friction and minimal wear, due to its titanium-nitride coating. The high surface quality of this ground twist drill bit, which is made from HSS (high-speed steel), allows for extended usage. It is suitable for use on alloyed and non-alloyed steel, malleable cast iron, sintered iron, new silver, copper, bronze and hard plastics such as perspex. The HSS Twist Drill Bit Titanium is manufactured to DIN 338. The drill bit is Type N (flute angle) with a 135-degree tip and a diameter tolerance of h8. Active cutting and perfect …

The SDS plus-3 Drill Bit offers durability when drilling in concrete. To prevent heat development, the 4-flute dura design provides effective dust removal for increased endurance. It is made of high-alloy steel, which is produced with an optimised hardening technology to withstand wear. For additional resistance, indented cutting edges are made from an ideal Bosch-controlled carbide blend. As proof of quality, the drill bit bears the test mark of the PGM Masonry Drill Bit Association Board, guaranteeing compliance with tight tolerances, exact drilling and the firm hold of fixings. The bit is intended for work on concrete and masonry and is to be used with rotary hammers with SDS plus holders.…

The HSS Twist Drill Bit PointTeQ enables fast drilling in metal due to its PointTeQ tip design. Quick and easy drilling starts are possible as the self-centering tip prevents wandering. Because of its increased drilling rate, less heat and wear are generated. The PointTeQ tip design remains sharp and ensures continuous durability. This bit is suitable for drilling clearance and pilot holes in alloyed and non-alloyed steel, non-ferrous metals, cast steel, cast iron and plastics. There is a low risk of breakage, especially for drill bits below 6 mm in diameter as the bit is manufactured to have a highly elastic body. Its black-oxide coated flute provides fast chip removal. The HSS Twist Drill …

Faithfull Standard masonry bits are for use in chucks up to 13mm capacity and are suitable for general purpose drilling including bricks, blocks and cement render when used in an impact or percussion drill. A roll formed and treated body with a heavy-duty Tungsten Carbide tip and fast spiral for quick waste removal.Manufactured to DIN 8039. Zinc plated finish and packed individually. Size.10 mm x 400 mm.Additional Information:• Diameter: 10.0mm• Overall Length: 400mm• Pack Qty.: 1

The Makita Performance SDS Plus range consists of European manufactured hammer drill bits with a patented high volume multi-flute that quickly channels the drilling dust from the hole, saving both time and money. Due to its aggressive design, the fast and durable carbide tip allows easy centering and spot drilling. Designed for regular professional use, providing excellent performance in the toughest of materials. Also excellent for drilling in high resistance materials such as Green Concrete or Engineering Brick. The unique reinforced flute geometry transfers more impact energy from the rotary hammer to the drill head, reducing stress for user and power tool. The design and technology innovations …

The HSS Twist Drill Bit Titanium offers maximum lifetime while drilling holes in metal. When using the appropriate cooling system, the drill bit has the lowest possible level of friction and minimal wear, due to its titanium-nitride coating. The high surface quality of this ground twist drill bit, which is made from HSS (high-speed steel), allows for extended usage. It is suitable for use on alloyed and non-alloyed steel, malleable cast iron, sintered iron, new silver, copper, bronze and hard plastics such as perspex. The HSS Twist Drill Bit Titanium is manufactured to DIN 338. The drill bit is Type N (flute angle) with a 135-degree tip and a diameter tolerance of h8. Active cutting and perfect …

Milwaukee SDS Plus 2-Cut drill bits have 3 offset aggressive power breakers. These produce a demolition effect and create micro cracks in the drilled material. Centering tip ensures immediate spot drilling with pin point accuracy and prevents skidding on smooth surfaces. Enlarged rebar chamfers prevent side tip damage when hitting rebar, this reduces the risk of the drill bit jamming when hitting rebar. Tapered shoulder design provides a thinner shoulder towards drill tip for less friction providing for greater speed. This is Ideal for cordless hammers identified from its tapered shoulder geometry. Reinforced flute has high volume flute geometry for optimum dust removal. Reinforced flute design …

The HSS Twist Drill Bit PointTeQ enables fast drilling in metal due to its PointTeQ tip design. Quick and easy drilling starts are possible as the self-centering tip prevents wandering. Because of its increased drilling rate, less heat and wear are generated. The PointTeQ tip design remains sharp and ensures continuous durability. This bit is suitable for drilling clearance and pilot holes in alloyed and non-alloyed steel, non-ferrous metals, cast steel, cast iron and plastics. There is a low risk of breakage, especially for drill bits below 6 mm in diameter as the bit is manufactured to have a highly elastic body. Its black-oxide coated flute provides fast chip removal. The HSS Twist Drill …

HSS Twist Drill Bit PointTeQ enables fast drilling in metal due to PointTeQ tip design Self-centering tip prevents wandering, making quick and easy drilling starts possible Increased drilling rate generates less heat and wear PointTeQ tip design remains sharp and ensures continuous durability The HSS Twist Drill Bit PointTeQ enables fast drilling in metal due to its PointTeQ tip design. Quick and easy drilling starts are possible as the self-centering tip prevents wandering. Because of its increased drilling rate, less heat and wear are generated. The PointTeQ tip design remains sharp and ensures continuous durability. This bit is suitable for drilling clearance and pilot holes in alloyed and …

Irwin Speedhammer Pointed Chisels are for use with SDS Max machines. Suitable for a wide range of applications: breaking through, breaking up concrete, light demolition work and chasing of channels for pipes and electrical conduit. Suitable for use on concrete and masonry and are supplied in a grey sandblasted professional finish.The Irwin IRW10502184 Speedhammer Max pointed chisel 280mm.Additional Information:• Type: Point• Size: 280mm

The IRWIN® HSS Pro Drill Bits are made from high-performance, high-speed steel. They have a 118° split point shape for increased performance and very good centring. The drill bits ensure precision starting, with no need to pre-punch or pilot drill. They penetrate the material quickly, requiring little effort and feed pressure. Manufactured to DIN 338 standards. DIN 338 drill bits are suitable for many trade and industrial applications in alloyed and unalloyed steel, non-ferrous metal, cast iron and plastics.This IRWIN® HSS Reduced Shank Pro Drill Bit has the following specification: Diameter: 11.0mmWorking Length: 94mmTotal Length: 142mmShank Diameter: 10mmAdditional Information:• …

Pilot drill bit for shank for hex adapter and SDS plusSpecifications:Diameter/width across flats mm: 8Total length mm: 120Shank: CylindricalMaterials:ConcreteStoneMaterials in Detail:ConcreteMasonry

Lasts up to 3x longer than a standard drill bitDrilling through reinforced concrete is a tough job, and it has traditionally taken its toll on drill bits. Regular two-cutter bits get stuck in rebar and they eventually break. The Full Carbide Head on the Expert SDS plus-7X is an advanced 4-cutter design made from a single piece of the toughest metal: It doesn’t jam and presents no weakness on impact.Thanks to Bosch Carbide Technology and the Full Carbide Head, the Expert SDS plus-7X lasts far longer than regular hammer drill bits. It punches through rebar effectively so there is no need to stop, re-target or change bits when you strike steel.For construction professionals drilling concrete an…

The Milwaukee Hammer Drill Bits have been designed with a 2 cutter carbide tip to allow for drilling into concrete, brick, block and soft material for electrical installations, lighting fixtures and holders. Our Hammer Drill Bits also features a red flute for easy identification along with a wide flute design to remove dust faster, while also reducing heat build-up, resulting in more holes per charge. Specifications • Cutting Width: 10mm • Length: 260mm • Pack Quantity: 1Features & Benefits• Tungsten carbide tipped drill bit allow drilling into concrete, aerated concrete blocks, masonry and granite • Wide red flute for optimal material extraction and easy identifiable …

Faithfull Standard masonry bits are for use in chucks up to 13mm capacity and are suitable for general purpose drilling including bricks, blocks and cement render when used in an impact or percussion drill. A roll formed and treated body with a heavy-duty Tungsten Carbide tip and fast spiral for quick waste removal.Manufactured to DIN 8039. Zinc plated finish and packed individually. Size.10 mm x 300 mm.Additional Information:• Diameter: 10.0mm• Overall Length: 300mm• Pack Qty.: 1

• Superior quality auger wood drill bit has a hexagonal shank for higher torque ranges demanded by this drill type.• Fully hardened with a screw point to aid location and smooth drilling.• Supplied in a plastic wallet.Superior quality auger wood drill bit has a hexagonal shank for higher torque ranges demanded by this drill type. Fully hardened with a screw point to aid location and smooth drilling. Supplied in a plastic wallet.Technical Specification:Size: ø18 x 460mmDimensions: Length: 5mm x Height: 525mmWeight: 0.406KgWarranty: Consumable

High quality metal twist drill bits for precise drilling in metal. Made out of high speed steel (HSS). A finely-tuned material elasticity provides for a long service life. Very good concentricity. Tough viscous tempered bits ensure a particularly long service life. The hexagonal shaft ensures very good power transfer. Drive: ¼" hexagon, suitable for holders as per DIN ISO 1173-D 6.3. Features and Benefits: • Twist bit for metal applications • Hex shaft for very good power transfer • HSS = high speed steel with split point • Finely-tuned material elasticity for great durability • Very good concentricity Contents: 848 HSS Metal Twist Drill Bits, 5.1 x 50 mm

The CWCL TCT series Pilot Pins are compatible with Rotabroach TCT cutters from 66mm to 100mm diameter and 50mm depth of cut.

Osborn Goldex 81504 series jobber drill bits.High Quaility HSS fully ground Titanium Coated Drill point for longer life. Suitable for drilling in steel, cast steel (alloyed and non alloyed), grey cast iron, graphite and malleable cast iron. Specifications • Standards: DIN 338 • Composition: High Speed Steel • Point Angle: 118° • Point Type & Helix Angle: N ~ 30° • Drill Body Tolerance: h8

Milwaukee MX4 SDS Plus drill bits have a symmetrical 4 cutter geometry (4 x 90°) and are ideal for making perfect round holes when fitting anchors. The high volume flutes ensure efficient removal of dust and debris while drilling, and a centering tip enables quick and accurate starting. Features & Benefits • Symmetrical 4 cutter geometry • High volume flutes ensure efficient removal of dust and debris • Centering tip for easy spot drilling with pinpoint accuracy • Welded solid carbide tips on sizes 5mm - 10mm • Increased carbide results in higher durability • Four breaker points pulverize material for faster drilling • Enhanced rebar guards for improved …

Lasts up to 3x longer than a standard drill bitDrilling through reinforced concrete is a tough job, and it has traditionally taken its toll on drill bits. Regular two-cutter bits get stuck in rebar and they eventually break. The Full Carbide Head on the Expert SDS plus-7X is an advanced 4-cutter design made from a single piece of the toughest metal: It doesn’t jam and presents no weakness on impact.Thanks to Bosch Carbide Technology and the Full Carbide Head, the Expert SDS plus-7X lasts far longer than regular hammer drill bits. It punches through rebar effectively so there is no need to stop, re-target or change bits when you strike steel.For construction professionals drilling concrete an…

The SDS plus-7 Drill Bit performs precision-drilling in reinforced concrete. Its full carbide head with 5 cutters is fused with IDS welding technology to drill with a very high level of accuracy. A vibration-reduced power transfer from the rotary hammer to the full carbide head is provided by the 2 + 2 flute design, which is made of high-alloy steel and created using optimised hardening technology. This offers the stability necessary for exact results. To prevent wandering and obtain a precise hole diameter, the Activeteq centring tip guides the drill position from the start. The bit is intended for use on masonry, concrete and reinforced concrete. To achieve accurate results, the visibility …

Bosch 2608833800 SDS Plus-5X Hammer Drill Bit 10mm x 200mm x 260mm The Bosch 2608833800 SDS Plus bits offer highly efficient drilling in reinforced concrete and masonry. They have a 4-flute design which provides fast dust removal so the bit can slice through concrete and rebar quickly with reduced wear. The centring tip prevents wandering and geometrical form prevents jamming. Features:
- SDS plus-5X Drill Bit offers highly efficient drilling in reinforced concrete
- Geometrical form of the 4-cutter head prevents jamming and breakage for optimal results
- “Turn-angle” head and 4-flute design provide fast dust removal for increased drilling speeds and reduced wear
- Centring tip guid…