Car Subwoofers

Diameter 250 mm / 10 Inch / 360 watt / Nominal Load 150 Watt / Impedance 4 Ohm

Inserts slugly into Gen-2 P3S trim rings. Protects against surround and cone damage. Sized to fit Gen-2 P3S woofers

10"/250mm Subwoofer Grille for Kenwood KFC-W2516PS 1 Grille Only. Subwoofer on the photo is not included.

Power Range: 150 W-350 W RMS RMS Power Handling: 350 W RMS Peak Power Handling: 1000 W PEAK Frequency Response: 30 Hz-200 Hz Material: Reinforced Parabolic Cone Structure with Poly-Mica Dust Cap & Pulp-Kevlar Cone Body

Car Subwoofer Speaker / Diameter 254 mm / 10 Inch / Mounting Depth 89 mm / 600 watt / Nominal Load 300 Watt / 83 dB / Impedance 2 x 4 Ohm

Space Saver - The combination of amplifier and subwoofer all into one, makes this ideal for spatially challenged vehicles. With a slim design, there are a few installation options. Embrace the Bass. Built-in Amplifier - A built-in 800 Max watt amplifier powers the subwoofer Pulse Width Modulated - This design controls the output voltage and current precisely by not only removing the output current sensing loss, but also eliminating all secondary feedback circuitry. It increases efficiency, is lighter, smaller reliable Variable Low-Pass Filter - A low-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. You will use the Low-pass filter to primarily …

Affordable big-bass performance - without taking up lots of room in your trunk or cargo area. Tough as nails. Load your cargo right on top of the sub for extra space – with plenty of bass! Full perimeter venting and UniPlate back plate and pole piece Stiff, injection-molded cone with 360-degree back bracing Utilizes extensive internal bracing, thick MDF construction and custom embroidery

6-Inch 2-WAY CAR AUDIO COMPONENT SPEAKER SYSTEM 125 Watts Max Each Side, 25 Watts RMS Each Side Built to handle all bass levels down to the lowest frequencies 4 Ohms Impedance Frequency Response: 30 - 30,000 Hz High efficiency and low distortion

Flat Subwoofer / Nominal Load 130 Watt

Protects against surround and cone damage. Sized to fit Gen-3 P2 & P3 woofers. Stamped mesh grille insert.

Boss Audio Systems BX-10 Subwoofer Ripper Series 350 RMS, 700 Watt max. Factory packaging

10" Protective Subwoofer Grill Works with Alpine SWA-10S4 Subwoofers Includes all Necessary Mounting Hardware

Car Subwoofer Speaker / Diameter 300 mm / 12 Inch / 300 watt / Nominal Load 150 Watt / Impedance 1 x 4 Ohm

Space-saving subwoofer solution Recommended power: 800 – 2500 watts. Voice coil 63 mm copper Long-stroke sandwich beading. Solid cast aluminium basket

Power - 3400 Watts Max x 1 @1-Ohm, 1700 Watts Max x 1 @2-Ohms, 850 Watts Max x 1 @4-Ohms 1 Ohm Stable - Able to continuously power loads of 1 Ohm without encountering difficulties such as overheating. Typically made to power up subwoofers that demand the heavier power load requirements to be able to perform the way they were made to Mosfet Power Supply - A MOSFET is an electrical switch that allows the flow of electrical current. It controls the output voltage and current precisely by removing the output current sensing loss & eliminating all secondary feedback circuitry Strapping Capable - You are able to strap two R3400D amplifiers and double the power that is being sent to your subwoofer(…

Plus One Woofer Cones Perimeter Illumination SSI (Switch-Selectable Impedance) One-piece Polymer basket High Sensitivity

Deep, powerful bass with power handling 275W RMS or 1100W Peak Mounting depth 6-1/2" (165mm) 25 - 175Hz frequency response 12" Subwoofer Car audio Subwoofer

Boxed Subwoofer / Diameter 270 mm / 11 Inch / 300 watt / Impedance 4 x 4 Ohm