Victron Energy Smart BatteryProtect 12/24V 100A BPR11002200
 |
 |
Close
Buy Victron Energy Smart BatteryProtect 12/24V 100A BPR11002200
When you make a purchase through links on our site, we may earn an affiliate commission.
Victron Victron Smart BatteryProtect SBP-220 (12V/24V-100A) | £55.50 |  | |||
Victron Energy Smart 12/24v-100a Protector Clear NT-1163 | £66.99 |  | |||
Victron Energy Victron Energy Smart BatteryProtect 12/24V 100A BPR11002200 | £95.00 |  | |||
Protects the battery against excessive discharge and can be used as a system on/off switchThe Smart BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine. The on/off input can be used as a system on/off switch.
12/24 V auto rangingThe Smart BatteryProtect automatically detects system voltage one time only.
Bluetooth: programming made easyWhen using Bluetooth to program the Smart BatteryProtect any required engage/disengage levels can be set. Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin (see manual). If required, Bluetooth can be disabled.
A special setting for Li-ion batteriesIn this mode the BatteryProtect can be controlled by the VE.Bus BMS.Note: the BatteryProtect can also be used as a charge interrupter in between a battery charger and a Li-ion battery. See connection diagram in the manual.
Ultra-low current consumptionThis is important in case of Li-ion batteries, especially after low voltage shutdown.
Over voltage protectionTo prevent damage to sensitive loads due to over voltage, the load is disconnected whenever the DC voltage exceeds 16.3 V respectively 32.6 V.
Ignition proofNo relays but MOSFET switches, and therefore no sparks.
Delayed alarm outputThe alarm output is activated if the battery voltage drops below the preset disconnect level during more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit proof open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay.
Delayed load disconnect and delayed reconnectThe load will be disconnected 90 seconds after the battery voltage drops below the preset level. If the battery voltage increases again to the connect threshold within this time period (after the engine has been started for example), the load will not be disconnected. The load will be reconnected 30 seconds after the battery voltage has increased to more than the preset reconnect voltage.
Current: 100 A
Voltage: 12 / 24 V
Made in: Netherlands
Current (A): 100.0
12/24 V auto rangingThe Smart BatteryProtect automatically detects system voltage one time only.
Bluetooth: programming made easyWhen using Bluetooth to program the Smart BatteryProtect any required engage/disengage levels can be set. Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin (see manual). If required, Bluetooth can be disabled.
A special setting for Li-ion batteriesIn this mode the BatteryProtect can be controlled by the VE.Bus BMS.Note: the BatteryProtect can also be used as a charge interrupter in between a battery charger and a Li-ion battery. See connection diagram in the manual.
Ultra-low current consumptionThis is important in case of Li-ion batteries, especially after low voltage shutdown.
Over voltage protectionTo prevent damage to sensitive loads due to over voltage, the load is disconnected whenever the DC voltage exceeds 16.3 V respectively 32.6 V.
Ignition proofNo relays but MOSFET switches, and therefore no sparks.
Delayed alarm outputThe alarm output is activated if the battery voltage drops below the preset disconnect level during more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit proof open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay.
Delayed load disconnect and delayed reconnectThe load will be disconnected 90 seconds after the battery voltage drops below the preset level. If the battery voltage increases again to the connect threshold within this time period (after the engine has been started for example), the load will not be disconnected. The load will be reconnected 30 seconds after the battery voltage has increased to more than the preset reconnect voltage.
Current: 100 A
Voltage: 12 / 24 V
Made in: Netherlands
Current (A): 100.0
Product description is based on database from online stores. Be sure to verify all information directly with seller before purchasing.
What to give to a motorist?10 practical gift ideas for drivers
How to choose a car inverter for creating autonomous power systems from a car batteryThe “auto-inverter / car battery” bundle allows you to wait out the blackouts with minimal discomfort
How to place an order?How to add store?
Remember that online store is responsible for accuracy of information about price, warranty and delivery!
We recommendCompare using chart →
charger, inverter, on battery: 6 V, 12 V, capacity 1.2 – 120 Ah, WET (Lead-Acid), AGM, GEL, charging current: up to 1 А, auto-adjustment, 95x58x33 mm, weight 0.29 kg
charger, inverter, on battery: 6 V, 12 V, capacity 3 – 60 Ah, WET (Lead-Acid), AGM, GEL, charging current: up to 2 А, auto-adjustment, desulfation, 240x140x60 mm, weight 0.27 kg
charger, inverter, on battery: 12 V, capacity 40 – 500 Ah, WET (Lead-Acid), GEL, charging current: up to 25 А, stepwise, desulfation, 235x65x130 mm, weight 1.9 kg
charger, inverter, on battery: 6 V, 12 V, capacity 5 – 140 Ah, charging current: from 2 А, up to 4 А, auto-adjustment, 244x60x114 mm
charger, inverter, on battery: 6 V, 12 V, capacity 5 – 120 Ah, WET (Lead-Acid), AGM, Li-Ion, charging current: up to 0.75 А, auto-adjustment, 205x80x60 mm, weight 0.3 kg
charger, inverter, on battery: 6 V, 12 V, capacity 3 – 120 Ah, WET (Lead-Acid), AGM, GEL, charging current: up to 1 А, auto-adjustment, desulfation
charger, inverter, on battery: 6 V, 12 V, capacity 1.2 – 120 Ah, WET (Lead-Acid), AGM, GEL, charging current: from 2 А, up to 4 А, auto-adjustment, desulfation, weight 0.6 kg
charger, inverter, on battery: 6 V, 12 V, capacity 10 – 150 Ah, WET (Lead-Acid), AGM, GEL, charging current: from 2 А, up to 6 А, auto-adjustment, desulfation, 100x150x240 mm, weight 0.7 kg
charger, inverter, on battery: 6 V, 12 V, capacity 1.2 – 120 Ah, WET (Lead-Acid), AGM, GEL, charging current: up to 5 А, auto-adjustment, desulfation
charger, on battery: 6 V, 12 V, capacity 2 – 20 Ah, charging current: up to 0.75 А, auto-adjustment, 50x80x30 mm, weight 0.22 kg
charger, inverter, on battery: 6 V, 12 V, capacity 6 – 200 Ah, WET (Lead-Acid), AGM, GEL, charging current: from 2 А, up to 4 А, auto-adjustment, desulfation, 235x75x50 mm, weight 0.5 kg
charger, inverter, on battery: 12 V, capacity 28 – 300 Ah, WET (Lead-Acid), GEL, charging current: up to 15 А, stepwise, 235x65x130 mm, weight 1.9 kg
